DOI QR코드

DOI QR Code

Flexural performance of composite beams with open-web π-shaped steel partially-encased by concrete

  • Liusheng Chu (School of Civil Engineering, Zhengzhou University) ;
  • Yunhui Chen (School of Civil Engineering, Zhengzhou University) ;
  • Jie Li (Sanda University) ;
  • Yukun Yang (Shanghai Jieyi Architectural Consulting Firm) ;
  • Danda Li (University of South Australia) ;
  • Xing Ma (University of South Australia)
  • 투고 : 2023.10.23
  • 심사 : 2024.01.24
  • 발행 : 2024.02.25

초록

Prefabricated partially-encased composite (PEC) structural component is widely used in construction industry due to its superior structural performance and easy assembly characteristic. However, the solid web in traditional PEC components tends to split concrete into two halves, thus potentially reduces structural integrity and requires double concrete pouring. To overcome the above disadvantages, a new PEC beam with open-web π-shaped steel is proposed in this paper. Four open-web PEC beams with varying sectional height, flange thickness and web void rate were constructed and tested under flexural loads. During experimental tests, all beams exhibited typical flexural failure modes with strong moment capacities and excellent ductility. Owing to the unique construction form of web opening, steel-concrete bonding properties were enhanced and very small relative steel-concrete slips were observed. Experimental results also showed that the flexural capacity of such PEC beams increased with the increase of the sectional height and flange thickness, while was not affected by the web void rate. At last, a flexural capacity formula of the open-web PEC beam was proposed based on the whole section plastic rule. The formula results agreed well with experimental results.

키워드

참고문헌

  1. Ahmada, S., Masria, A. and Saleh, Z.A. (2018), "Analytical and experimental investigation on the flexural behavior of partially encased composite beams", Alexandria Eng. J., 57(3), 1693-1712. https://doi.org/10.1016/j.aej.2017.03.035.
  2. Ahn, J. and Lee, C. (2017), "Fire behavior and resistance of partially encased and slim-floor composite beams", J. Construct. Steel Res., 129, 276-285. https://doi.org/10.1016/j.jcsr.2016.11.018.
  3. Assi, I.M., Abed, S.M. and Hunaiti, Y.M. (2002), "Flexural strength of composite beams partially encased in lightweight concrete", J. Appl. Sci., 2(3), 320-323. https://doi.org/10.3923/jas.2002.320.323.
  4. Cao, X., Li, X., Zhu, Y. and Zhang, Z. (2015), "A comparative study of environmental performance between prefabricated and traditional residential buildings in China", J. Cleaner Product., 109, 131-143. https://doi.org/10.1016/j.jclepro.2015.04.120.
  5. Chopra, A.K. (2010), Dynamics of Structures: Theory and Applications to Earthquake Engineering Higher Education Press, Beijing, China. (in Chinese).
  6. Correia, A.J.P.M. and Rodrigues, J.P.C. (2010), "Fire resistance of partially encased steel columns with restrained thermal elongation", J. Construct. Steel Res., 67(4), 593-601. https://doi.org/10.1016/j.jcsr.2010.12.002.
  7. Han, S.J., Joo, H.E., Choi, S.H., Heo, I. and Kim, K.S. (2021), "Flexural behavior of prestressed hybrid wide flange beams with hollowed steel webs", Steel Compos. Struct., 38(6), 691-703. https://doi.org/10.12989/scs.2021.38.6.691.
  8. Hong, J., Shen, G.Q., Mao, C., Li, Z. and Li, K. (2016), "Life-cycle energy analysis of prefabricated building components: an inputa output-based hybrid model", J. Product., 112, 2198-2207. https://doi.org/10.1016/j.jclepro.2015.10.030.
  9. Jiang, Y.C., Hu, X.M., Hong, Wan. and Wang, B.L. (2016), "Experimental study and theoretical analysis of partially encased continuous composite beams", J. Construct. Steel Res., 117,152-160. https://doi.org/10.1016/j.jcsr.2015.10.009.
  10. Kindmann, R., Bergmann, R., Cajot, L.G. and Schleich, J.B. (1993), "Effect of reinforced concrete between the flanges of the steel profile of partially encased composite beams", J. Construct. Steel Res., 27(1), 107-122. https://doi.org/10.1016/0143-974X(93)90009-H.
  11. Liang, J.F., Zhang, L.F., Yang, Y.H. and Wei, L. (2021), "Flexural behavior of partially prefabricated partially encased composite beams", Steel Compos. Struct., 6, 38. https://doi.org/10.12989/scs.2021.38.6.705.
  12. Marinopoulou, A.A., Balopoulos, V.D. and Kalfas C N. (2007), "Simulation of partially encased composite steel-concrete columns with steel columns", J. Construct. Steel Res., 63(8), 1058-1065. https://doi.org/10.1016/j.jcsr.2006.11.003.
  13. Nakamura, S.I. and Narita, N. (2003), "Bending and shear strength of partially encased composite I-girders", J. Construct. Steel Res., 59(12), 1435-1453. https://doi.org/10.1016/S0143-974X(03)00104-4.
  14. Nardin, S.D. and Debs, A.L.H.C.E. (2009), "Study of partially encased composite beams with innovative position of stud bolts", J. Construct. Steel Res., 65(2), 342-350. https://doi.org/10.1016/j.jcsr.2008.03.021.
  15. potential for using prefabrication in residential buildings in China", Energy Build., 166, 561-570. https://doi.org/10.1016/j.enbuild.2017.12.045.
  16. T/CECS 719-2020 (2021), Technical Specification for Partially-Encased Composite Structures of Steel and Concrete, China Architecture & Building Press, Beijing, China.
  17. Wu, G., Yang, R., Li, L., Bi, X., Liu, B., Li, S. and Zhou, S. (2019), "Factors influencing the application of prefabricated construction in China: From perspectives of technology promotion and cleaner production", J. Cleaner Product., 219, 753-762. https://doi.org/10.1016/j.jclepro.2019.02.110.
  18. Zhu, H., Hong, J., Shen, G.Q., Mao, C., Zhang, H. and Li, Z. (2018), "The exploration of the life-cycle energy saving