Journal of the Korea Safety Management & Science (대한안전경영과학회지)

Korea Safety Management & Science (대한안전경영과학회)
권호 표지
DOI QR코드

DOI QR Code

Safety Improvements of Guardrail Coating Vehicle Using FMECA and HAZOP

FMECA와 HAZOP을 활용한 가드레일 코팅차량의 안전성 향상

  • U.P. Chong (Graduate School of Industry, University of Ulsan) ;
  • H.C. Park (Graduate School of Industry, University of Ulsan) ;
  • B.C. Ahn (Graduate School of Industry, University of Ulsan) ;
  • Y.S. Park (Graduate School of Industry, University of Ulsan) ;
  • D.S. Han (KEMP Corporation) ;
  • H.J. Chon (KEMP Corporation)
  • 정의필 (울산대학교 산업대학원) ;
  • 박현철 (울산대학교 산업대학원) ;
  • 안병철 (울산대학교 산업대학원) ;
  • 박영수 (울산대학교 산업대학원) ;
  • 한덕수 ((주)캠프) ;
  • 전현준 ((주)캠프)
  • Received : 2023.08.19
  • Accepted : 2023.09.27
  • Published : 2023.09.30
Download PDF
⟨ Previous Next ⟩

Abstract

This study uses FMECA (Failure Modes, Effects, and Criticality Analysis) and HAZOP (Hazard and Operability), which are widely applied in industrial areas, among risk assessment methods, and applies them to the same system. While FMECA evaluates system failure conditions and analyzes risks, HAZOP evaluates the system comprehensively by evaluating operational risks that may occur based on system parameters. According to data released by the Ministry of Land, Infrastructure and Transport, as of December 2021, the length of roads in Korea is 113,405 km, and the repair of guardrails that have expired must be fixed urgently in terms of traffic safety. Replacing all of these guardrails with new ones requires a very large cost, but if the guardrails are repaired with a vehicle equipped with the G-Save method, carbon emissions are reduced, the repair period is shortened, and great economic benefits can be obtained. However, risk assessment for guardrail coating vehicles has not been done so far. Focusing on this point, this study aims to evaluate the risk of these coating vehicles and describe the results. Finally, we found that the Risk Priority Numbers(RPN) in the FMECA risk assessment were greatly reduced, and 6 risk factors from HAZOP risk assessment and actions were taken.

Keywords

Acknowledgement

본 연구는 국토교통부지원(RS-2022-00144120)에 의하여 연구되었음.

References

  1. H. G. Hwang, J. W. Kang, J. S. Lee(2015), "A development of component vulnerability analysis program for armored fighting vehicle using criticality based on FMECA." Journal of the Korea Institute of Information and Communication Engineering, 19(8):1973-1980.  https://doi.org/10.6109/jkiice.2015.19.8.1973
  2. S. J. An, S. H. Song(2012), "Integrated safety risk assessment and response preparation on construction site formwork using FMECA method." Journal of Korea Safety Management & Science, 14(3):39-48.  https://doi.org/10.12812/KSMS.2012.14.3.039
  3. G. Park, K. Choi(2023), "Reliability improvement of points system using FMECA." The Transactions of the Korean Institute of Electrical Engineers, 72(5):678-687.  https://doi.org/10.5370/KIEE.2023.72.5.678
  4. S. R. Kim, Y. S. Moon, K. H. Choi(2015), "FMECA procedure for failure analysis of train high-speed circuit breaker." Journal of the Korea Academia-Industrial Cooperation Society, 16(5):3370-3377.  https://doi.org/10.5762/KAIS.2015.16.5.3370
  5. C. You, J. Kim(2018), "HAZOP study for risk assessment and safety improvement strategies of CO2 separation process." Korean Journal of Chemical Engineering, 56(3):335-342. 
  6. J. Park, D. Park, C. Chae, J. Heo, K. Park(2022), "Improvement of hydrogen fueling protocol by HAZOP and LOPA." Korean Journal of Hazardous Materials, 10(1):82-90.  https://doi.org/10.31333/kihm.2022.10.1.82
  7. H. Noh, S. H. Park, S. Cho, K. Kang, H. Kim(2020), "A case study on the risk assessment for offshore plant solid desiccant dehydration package by using HAZOP." Journal of the Korean Society of Industry Convergence, 23(4):560-581. 
  8. J. G. Ohn, S. Y. Moon(2017), "A study on HAZOP by object model methodology." Journal of Korean Society for Urban Railway, 5(4):1059-1065.  https://doi.org/10.24284/JKOSUR.2017.12.5.4.1059
  9. N. Pancholi1, M. G. Bhatt(2016), "Multicriteria FMECA based decision-making for aluminium wire process rolling mill through COPRAS-G." Journal of Quality and Reliability Engineering, 2016 (8421916):1-8.  https://doi.org/10.1155/2016/8421916
  10. B. Suharjo, O. S. Suharyo, A. Bandono(2019), "Failure Mode Effect and Critically Analysis(FMECA) for determination time interval replacement of critical components in warships RADAR." Journal of Theoretical and Applied Information Technology, 97(10):2861-2871. 
  11. Q. Zhang, C. Zhou, Y. C. Tian, N. Xiong, Y. Qin, B. Hu(2018), "A fuzzy probability bayesian network approachfor dynamic cybersecurity risk assessment in industrial control systems." IEEE Transactions on Industrial Informatics, 14(6):2497-2506.  https://doi.org/10.1109/TII.2017.2768998
  12. R. Hokmabadi, A. Karimi(2023), "Application of operation and risk study technique (HAZOP) in assessing safety and health risks: A case study in CGS station." ICRSE2023, 2023:1-8. 
  13. Ministry of Land, Infrastructure and Transport Press Release(2022). 
  14. KEMP Corporation(2020, January 31), Method for surface treatment of hot-dip galvanized metal for surface repairing and improving corrosion resistance. Patent No. 1020743260000. 
  15. S. J. Song, J. W. Lee(2019), Method of risk assessment and analysis. Sung An Dang. 
  16. KEMP Corporation(2021), The zinc restoration technology. The Report of Technical Descriptions. 
  17. U. P. Chong, H. C. Park, Y. S. Park, B. C. Ahn, D. Y. D. Hwang, H. J. Chon, D. Y. Kim(2022), "Preliminary hazard analysis for vehicles with G-save for guardrail maintenance." The Korea Institute of Surface Engineering 2022 Fall Meeting, Kwang Ju, Korea.