Steel and Composite Structures

  • 제47권3호
  • /
  • Pages.423-436
  • /
  • 2023
  • /
  • 1229-9367(pISSN)
  • /
  • 1598-6233(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Shear strength and shear behaviour of H-beam and cruciform-shaped steel sections for concrete-encased composite columns

  • Keng-Ta Lin (Department of Civil and Environmental Engineering, National University of Kaohsiung) ;
  • Cheng-Cheng Chen (Department of Construction Engineering, National Taiwan University of Science and Technology)
  • 투고 : 2022.04.29
  • 심사 : 2023.04.21
  • 발행 : 2023.05.10
⟨ 이전 논문 다음 논문 ⟩

초록

In this research, we tested 10 simply supported concrete-encased composite columns under monotonic eccentric loads and investigated their shear behaviour. The specimens tested were two reinforced concrete specimens, three steel-reinforced concrete (SRC) specimens with an H-shaped steel section (also called a beam section), and five SRC specimens with a cruciform-shaped steel section (also called a column section). The experimental variables included the transverse steel shape's depth and the longitudinal steel flange's width. Experimental observations indicated the following. (1) The ultimate load-carrying capacity was controlled by web compression failure, defined as a situation where the concrete within the diagonal strut's upper end was crushed. (2) The composite effect was strong before the crushing of the concrete outside the steel shape. (3) We adjusted the softened strut-and-tie SRC (SST-SRC) model to yield more accurate strength predictions than those obtained using the strength superposition method. (4) The MSST-SRC model can more reasonably predict shear strength at an initial concrete softening load point. The rationality of the MSST-SRC model was inferred by experimentally observing shear behaviour, including concrete crushing and the point of sharp variation in the shear strain.

키워드

참고문헌

  1. ACI Committee 318 (2014), Building Code Requirements for Structural Concrete (ACI 318-14) and Commentary (ACI 318R-14), American Concrete Institute, Farmington Hills, Michigan, USA.
  2. AISC 360-16 (2016), Specification for Structural Steel Building, American Institute of Steel Construction, Chicago, Illinois, USA.
  3. Architectural Institute of Japan (2014), AIJ Standards for Structural Calculation of Steel Reinforced Concrete Structures, Toyko, Japan.
  4. Campian, C., Nagy, Z. and Pop M. (2015), "Behavior of fully encased steel-concrete composite columns subjected to monotonic and cyclic loading", Procedia Eng., 117, 439-451. https://doi.org/10.1016/j.proeng.2015.08.193.
  5. Chen, B., Wu, J., Liu, C., Liu, Y., Zhou, W. and Xiao Y. (2021), "Analysis for shear behavior of SRC deep beams based on tests, digital image correlation technique, and finite Elemental simulation", Shock Vib., 2021, https://doi.org/10.1155/2021/5964480.
  6. Chen, C.C., Lin, K.T. and Chen, Y.J. (2018), "Behavior and shear strength of steel shape reinforced concrete deep beams", Eng. Struct., 175, 425-435, https://doi.org/10.1016/j.engstruct.2018.08.045.
  7. Deng, M.K., Ma F.D., Li, B.Z. and Liang X.W. (2017), "Aanlysis on shear capacity of SRC deep beams based on modified strut-and-tie model", Eng. Mech., 34(12), 95-103, https://doi.org/10.6052/j.issn.1000-4750.2016.08.0593.
  8. Foster, S.J. and Gilbert, R.I. (1996), "The design of nonflexural members with normal and high strength concrete", ACI Struct. J., 93(1), 3-10. https://doi.org/10.14359/967.
  9. Hajjar, J.F. (2002), "Composite steel and concrete structural systems for seismic engineering", J. Constr. Steel Res., 58(5-8), 703-723. https://doi.org/10.1016/S0143-974X(01)00093-1.
  10. Hwang, S.J. and Lee, H.J. (2002), "Strength prediction for discontinuity regions by softened strut-and-tie model", J. Struct. Eng., ASCE, 128(12), 1519-2002. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:12(1519).
  11. Hwang, S.J., Lu, W.Y. and Lee, H.J. (2000), "Shear strength prediction for deep beams", ACI Struct. J., 97(3), 367-376. https://doi.org/10.14359/9624.
  12. Lai, B., Liew, J.Y.R., Venkateshwaran, A. and Li, S. (2020), "Assessment of high-strength concrete encased steel composite columns subject to axial compression", J. Constr. Steel Res., 164, https://doi.org/10.1016/j.jcsr.2019.105765.
  13. Lim, E. and Hwang, S.J. (2016), "Modeling of strut-and-tie parameters of deep beams for shear strength prediction", Eng. Struct., 108, 104-112, https://doi.org/10.1016/j.engstruct.2015.11.024.
  14. Ma H., Xue J., Liu Y. and Zhang X. (2015), "Cyclic loading tests and shear strength of steel reinforced recycled concrete short columns", Eng. Struct., 92(1), 55-68. https://doi.org/10.1016/j.engstruct.2015.03.009.
  15. Ministry of Interior (2011), Specification and Commentary for Steel Reinforced Concrete, R.O.C Taiwan.
  16. Wallace, J.W. (1992), BIAX: Revision 1A Computer program for the analysis of reinforced concrete and reinforced masonry sections, Report No. CU/Cee-92/4, Department of Civil and Environmental Engineering, Clarkson University, Potsdam, New York.
  17. Xiao, Y.F., Zeng, L., Cui, Z.K., Jin, S.Q. and Chen, Y.G. (2017), "Experimental and analytical performance evaluation of steel beam to concrete-encased composite column with unsymmetrical steel section joints", Steel Compos. Struct., 23(1), 17-29. https://doi.org/10.12989/scs.2017.23.1.017
  18. Xue, Y., Yang, Y. and Yu, Y. (2020), "Shear Strength model for steel reinforced concrete composite members: short columns and deep beams", Eng. Struct., 216, https://doi.org/10.1016/j.engstruct.2020.110748.
  19. Zhao, B., He, J., Lu, X., Zhou, B. and Yu, L. (2012), "On seismic design of composite high-rise buildings with SRC column, steel beam and RC core tube", Proceeding of 15th World Conference on Earthquake Engineering, Lisbon, Portugal, September.
  20. Zhu, W., Jia, J., Gao, J. and Zhang F. (2016), "Experimental study on steel reinforced high-strength concrete columns under cyclic lateral force and constant axial load", Eng. Struct., 125, 191-204, https://doi.org/10.1016/j.engstruct.2016.07.018.