DOI QR코드

DOI QR Code

Analysis on inclined or rounded tip piles using 3D printing technology and FE analysis

  • Jaehong Kim (Department of Civil and Environmental Engineering, Dongshin University) ;
  • Junyoung Ko (Department of Civil Engineering, Chungnam National University) ;
  • Dohyun Kim (Department of Civil and Environmental Engineering, Hanbat National University)
  • Received : 2022.11.28
  • Accepted : 2023.03.07
  • Published : 2023.04.25

Abstract

To test the effect of various pile tip shape series of model scale loading tests were carried out on test piles with special pile tips. Special pile tips were made using the 3D printer and were attached to the bottom end of the test pile for loading tests. The pile tips were made to have 30°, 45°, 60° inclined tips, as well as a rounded tip. The main objective of the test was to observe the effect of various pile tip shapes on settlement and penetrability of the pile. Moreover, a numerical model simulating the pile loading test carried out in this study was established and verified based on the loading test results. From this, the stress concentration around the pile tip was investigated. This will allow us to analyze the decrease of stress concentration around the pile tip which is the main cause of the pile tip damage during pile installation. However, modifying the pile tip shape will eventually increase the settlement of the pile. By estimating the degree of increase in pile settlement, the viability and the efficiency of the pile shape modification was judged. In addition, case studies on the effect of different pile tip shape and ground conditions on pile settlement and stress dispersion was conducted.

Keywords

References

  1. ABAQUS CAE (2019), User's manual, Dassault Systemes Simulia, Rhode Island, USA.
  2. Cho, C., Kim, H. and Kim, W. (2004), "Bearing capacity evaluation of the drilled shaft using small model test", J. Korean Geotech. Soc., 20(5), 117-126.
  3. Current state of urban planning: Statistical information report (2022), Korea Land and Geospatial Informatix Corporation; Jeonju, Republic of Korea.
  4. Deisman, N., Flottmann, T., Guo, Y., Hodder, K.J., Chalaturnyk, R.J. and Leonardi, C. (2019) "Using 3D printed synthetic rock for systematic evaluation of mechanical properties in coal", Asian Pacific Unconventional Resources Technology Conference, November 18-19, Brisbane, Queensland, Australia, SPE. https://doi.org/10.15530/AP-URTEC-2019-198255.
  5. Gavin, K.G. and Lahane, B.M. (2003), "The shaft capacity of pipe piles in sand", Can. Geotech. J., 40(1), 36-45. https://doi.org/10.1139/t02-093.
  6. Hodder, K.J., Nychka, J.A. and Chalaturnyk, R.J. (2018) "Process limitations of 3D printing model rock", Prog. Addit. Manuf., 3(3). https://doi.org/10.1007/s40964-018-0042-6.
  7. Hoffmann, M., Zarkiewicz, K., Zielinski, A., Skibicki, S. and Marchewka, L. (2021), "Foundations piles - A new feature for concrete 3D printers", Materials, 14(10), https://doi.org/10.3390/ma14102545.
  8. Jeong, S., Kim, D. and Park, J. (2021), "Empirical bearing capacity formula for steel pipe prebored and precast piles based on field tests", ASCE Int. J. Geomech., 21(9). https://doi.org/10.1061/(ASCE)GM.1943-5622.0002112.
  9. Kim, D. (2018), "Proposed shaft resistance of prebored and precast pile using field loading test", Ph.D thesis, Yonsei University, Seoul, Republic of Korea.
  10. Kim, D. (2021), "Large deformation finite element analyses in TBM tunnel excavation: CEL and auto-remeshing approach", Tunn. Undergr. Sp. Tech., 116. https://doi.org/10.1016/j.tust.2021.104081.
  11. Kim, D. and Jeong, S. (2021), "Estimation of the excavation damage zone in TBM tunnel using large deformation FE analysis", Geomech. Eng., 24(4), 323-335. https://doi.org/10.12989/gae.2021.24.4.323.
  12. Kim, D., Jeong, S. and Park, J. (2020), "Analysis on shaft resistance of the steel pipe prebored and precast piles based on field load-transfer curves and finite element method", Soil. Found., 60, 478-495. https://doi.org/10.1016/j.sandf.2020.03.011.
  13. Ko, J. and Jeong, S. (2015), "Plugging effect of open-ended piles in sandy soil", Can. Geotech. J., 52, 535-547. doi/10.1139/cgj-2014-0041.
  14. Kumara, J., Kurashina, T. and Kikuchi, Y. (2016), "Effects of pile geometry on bearing capacity of open-ended piles driven into sands", Geomech. Eng., 11(3), 385-400. https://doi.org/10.12989/gae.2016.11.4.385.
  15. Lee, C., Jeon, Y., Kim, S. and Park, I. (2016), "The influence of tunneling on the behavior of pre-existing piled foundations in weathered soil", Geomech. Eng., 11(4), 553-570. https://doi.org/10.12989/gae.2016.11.4.553.
  16. Orazalin, Z. (2017), "Analysis of large deformation offshore geotechnical problems in soft clay", Ph.D thesis, Massachusetts Institute of Technology, Cambridge MA, USA.
  17. Orazalin, Z. and Whittle, A. (2018), "Realistic numerical simulations of cone penetration with advanced soil models", Cone Penetration Testing 2018, Delft, June.
  18. Sajjadi, S., Mirzaei, M., Nasab, A.F., Ghezelje, A., Tadayonfar, G. and Sarkardeh, H. (2016), "Effect of soil physical properties on infiltration rate", Geomech. Eng., 10(6), 727-736. https://doi.org/10.12989/gae.2016.10.6.727.
  19. Song, L., Jiang, Q., Shi, Y., Feng, X., Li, Y., Su, F. and Liu, C. (2018), "Feasibility investigation of 3D printing technology for geotechnical physical models: Study of tunnels", Rock Mech. Rock Eng., 51, 2617-2637. https://doi.org/10.1007/s00603-018-1504-3.
  20. Takemura, T., Isobe, Y., Okuzawa, K., Sanoki S., Shimo, M., Suzuki, K., Seiki, T., Nishimoto, S., Hamamoto, S. and Fujii, Y. (2019), "A review on application of 3D printer to geotechnical engineering", Jpn. Geotech. J., 14(4), https://doi.org/10.3208/jgs.14.377.