DOI QR코드

DOI QR Code

차량용 미세먼지 센서용 소형 축류팬의 유동과 소음 성능 개선

Improvement in flow and noise performances of small axial-flow fan for automotive fine dust sensor

  • 투고 : 2023.01.09
  • 심사 : 2023.01.25
  • 발행 : 2023.01.31

초록

최근 차량 내 공기 질에 대한 관심이 증가함에 따라 공기 질 측정을 위한 미세먼지 감지 센서의 사용이 보편화되고 있다. 차량 내 에어컨 시스템에 설치되는 미세먼지 감지 센서 내에는 센서에 직접적으로 먼지가 가라앉지 않도록 하기 위한 축류팬이 삽입되어 있다. 센서 작동 시 축류팬의 회전으로 인한 유동 소음은 미세먼지 감지 센서의 주요 소음원으로 작용한다. 차량의 전동화가 급격화가 진행되면서 이러한 유동소음은 미세먼지센서의 제품 경쟁력의 하나로 인식되고 있다. 본 연구에서는 이러한 미세먼지센서용 소형 축류팬의 유동 성능을 개선하여 동일 유량에서 소음을 점감하였다. 먼저 대상 소형 축류팬의 공기역학적 성능을 분석하기 위해 약 2000만 개의 격자로 구성된 가상 팬 성능시험기를 구축하였다. 또한, 유량의 정확한 예측 뿐만 아니라 유동소음의 직접 계산을 위하여 압축성 대와류모사법을 사용하여 유동장을 모사하였다. 수치방법의 유효성은 예측결과와 실험 결과와의 비교를 통하여 확인하였다. 유효성이 검증된 수치 기법을 이용하여 피치각이 유동 성능에 미치는 영향을 분석하였고, 유량을 최대화할 수 있는 피치각을 도출하였다. 최적 피치각을 적용한 축류팬을 사용했을 때 유량은 8.1 % 증가하고 동일 유량에서 소음이 0.8 dBA 감소함을 확인하였다.

Recently, as interest in air quality in vehicles increases, the use of fine dust detection sensors for air quality measurement is becoming common. An axial-flow fan is inserted in the fine dust sensor installed in the air conditioning system in the vehicle to prevent dust from sinking directly on the sensor. When the sensor operates, the flow noise caused by the rotation of the axial-flow fan acts as a major noise source of the fine dust sensor. flow noise is recognized as one of the product competitiveness of fine dust sensors. In this study, the noise was gradually reduced at the same flow rate by improving the flow performance of the small axial flow fan. First, a virtual fan performance tester consisting of about 20 million grids was developed to analyze the aerodynamic performance of the target small axial-flow fan. In addition, the flow field was simulated by using compressible Large Eddy Simulation for direct computation of flow noise as well as high-accurate prediction of flow rate. The validity of numerical method are confirmed through the comparison of predicted results with experimental ones. After the effects of pitch angle on flow performance were analyzed using the verified numerical method, the pitch angle was determined to maximize the flow rate. It was found that the flow rate was increased by 8.1 % and noise was reduced by 0.8 dBA when the axial-flow fan with the optimum pitch angle was used.

키워드

참고문헌

  1. S. Lee, S. Heo, C. Cheong, S. Kim, and M. Seo, "Computaion of internal BPF noise of axial circulating fan in refrigerators" (in Korean), J. KSNVE. 19, 454-461 (2009). https://doi.org/10.5050/KSNVN.2009.19.5.454
  2. G. Ren, S. Heo, C. Cheong, and T. Kim, "Response surface method based optimization of the shroud of an axial cooling fan for high performance and low noise," JMST. 27, 33-42 (2012).
  3. F. Gue, C. Cheong, and T. Kim, "Development of lownoise axial cooling fans in a household refrigerator," JMST. 25, 2995-3004 (2011).
  4. D. Shin, S. Heo, C. Cheong, T. Kim, and J. Jung, "Development of high-performance/low-noise centrifugal fan circulating cold air inside a household refrigerator by reduction of vortex flow" (in Korean), J. KSNVE. 26, 428-435 (2016). https://doi.org/10.5050/KSNVE.2016.26.4.428
  5. S. Ryu, S. Kim, C. Cheong, J. Kim, B. Park, and S. Park, "Optimization of flow performance by designing orifice shape of outdoor unit of air-conditioner" (in Korean), J. Acoust. Soc. Kr. 36, 371-377 (2017).
  6. J. Choi, S. Ryu, C. Cheong, T. Kim, and J. Koo, "Development of high performance and low noise axial-flow fan for cooling machine room of refrigerator using airfoil-cascade analysis and surface ridge shape" (in Korean), J. Acoust. Soc. Kr. 39, 515-523 (2020).
  7. P. Yu, X. Song, J. Bai, and H. Xiao, "Optimization of noise blade of small axial fan at low reynolds number," Proc. Internoise, 236-256 (2021).
  8. E. Quaranta, "Design of axial flow fans for reduced noise and improved efficiency," Proc. Internoise, 3649- 3662 (2021).
  9. S. Ryu, M. Jung, Y. Song, and C. Cheong, "Numerical comparative study on high-fidelity prediction of aerodynamic noise from centrifugal fan system" (in Korean), J. Acoust. Soc. Kr. 41, 713-722 (2022).
  10. ISO 3745:2012, Acoustics - Determination of Sound Power Levels and Sound Energy Levels of Noise Sources Using Sound Pressure - Precision Method for Anechoic Rooms and Hemi-Anechoic Rooms, 2012.