초록
노후 교량의 안전성을 평가하는 방법에 있어서 동특성과 처짐은 구조계의 강성과 직접 연관이 있으며, 처짐의 경우에는 교량 사용자가 직접 감지할 수 있는 물리량으로 가장 중요한 인자이다. 하지만 교량의 처짐을 측정하기 위해서는 교량의 하부에 처짐계를 설치하고 교통 차단 및 재하시험을 실시해야 하는 번거로움이 있어 교량의 환경에 따라서 비용이 증가하거나 측정이 불가능한 문제들이 발생하고 있다. 본 연구에서는 처짐계의 설치 없이 가속도계만을 이용하고 재하시험 없이 상시 진동을 이용하여 교량의 처짐을 측정하는 방법을 제안하였다. 상시 진동을 이용한 교량 동특성 및 처짐 분석을 위해 단순한 연산으로 빠른 분석이 가능하다고 알려진 TDD 기법을 이용하여 교량의 모드형상과 고유진동수를 추출하였으며, 유연도 분석을 통하여 교량의 단위하중 처짐을 분석하여 정적 처짐까지 산정하였다. 본 제안 기술의 검증을 위해 공용중 교량인 C대교(사장교)에 적용하여 모드형상, 고유진동수, 정적 처짐 분석을 수행하였으며 재하시험 실측값과 구조해석 자료와 비교하였다. 그 결과 모드형상 및 고유진동수는 0.42~1.13 %, 중앙경간에서의 최대 처짐은 3.58 %의 오차율을 확인하였다. 따라서 제안기술은 처짐계의 설치가 어려워 실측이 불가능한 교량의 처짐을 추정하여 설계값 및 해석값 대비 처짐 발생량 비교로 교량의 안전성을 간접적으로 파악할 수 있는 근거 자료로 활용 가능할 것으로 사료된다.
In safety assessment of a aged bridge, dynamic characteristics and displacement are directly related to the rigidity of the structural system, especially displacement is the most important factor as the physical quantity that the bridge user can directly detect. However, in order to measure the displacement of the bridge, it is difficult to install displacement sensors at the bottom of the bridge and conduct traffic blocking and loading tests, resulting in increased costs or impossible measurements depending on the bridge's environment. In this study, a method of measuring the displacement of a bridge using only accelerometers without installing displacement sensors and ambient vibration without a loading test was proposed. For the analysis of bridge dynamic characteristics and displacement using ambient vibration, the mode shape and natural frequency of the bridge were extracted using a TDD technique known to enable quick analysis with simple calculations, and the unit load displacement of the bridge was analyzed through flexibility analysis to calculate static displacement. To verify this proposed technology, an on-site test was conducted on C Bridge, and the results were compared with the measured values of the loading test and the structural analysis data. As a result, it was confirmed that the mode shape and natural frequency were 0.42 to 1.13 % error ratio, and the maximum displacement at the main span was 3.58 % error ratio. Therefore, the proposed technology can be used as a basis data for indirectly determine the safety of the bridge by comparing the amount of displacement compared to the design and analysis values by estimating the displacement of the bridge that could not be measured due to the difficulty of installing displacement sensors.