DOI QR코드

DOI QR Code

Bolt looseness detection and localization using time reversal signal and neural network techniques

  • Duan, Yuanfeng (College of Civil Engineering and Architecture, Zhejiang University) ;
  • Sui, Xiaodong (College of Civil Engineering and Architecture, Zhejiang University) ;
  • Tang, Zhifeng (Institute of Advanced Digital Technologies and Instrumentation, Zhejiang University) ;
  • Yun, Chungbang (College of Civil Engineering and Architecture, Zhejiang University)
  • Received : 2022.03.10
  • Accepted : 2022.07.21
  • Published : 2022.10.25

Abstract

It is essential to monitor the working conditions of bolt-connected joints, which are widely used in various kinds of steel structures. The looseness of bolts may directly affect the stability and safety of the entire structure. In this study, a guided wave-based method for bolt looseness detection and localization is presented for a joint structure with multiple bolts. SH waves generated and received by a small number (two pairs) of magnetostrictive transducers were used. The bolt looseness index was proposed based on the changes in the reconstructed responses excited by the time reversal signals of the measured unit impulse responses. The damage locations and local damage severities were estimated using the damage indices from several wave propagation paths. The back propagation neural network (BPNN) technique was employed to identify the local damages. Numerical and experimental studies were conducted on a lap joint with eight bolts. The results show that the total damage severity can be successfully detected under the effect of external force and measurement noise. The local damage severity can be estimated reasonably for the experimental data using the BPNN constructed by the training patterns generated from the finite element simulations.

Keywords

Acknowledgement

The authors acknowledge the supports from the National Key R&D Program of China (2018YFE0125400, 2019YFE0112600) and National Natural Science Foundation of China (Grant Nos. 52078459, U1709216).

References

  1. Ahmadian, H. and Jalali, H. (2007), "Identification of bolted lap joints parameters in assembled structures", Mech. Syst. Signal Process., 21(2), 1041-1050. https://doi.org/10.1016/j.ymssp.2005.08.015
  2. Amerini, F. and Meo, M. (2010), "Structural health monitoring of bolted joints using linear and nonlinear acoustic/ultrasound methods", Struct. Health Monitor., 10(6), 659-672. https://doi.org/10.1177/1475921710395810
  3. Baghalian, A., Senyurek, V.Y., Tashakori, S., McDaniel, D. and Tansel, I.N. (2018), "A novel nonlinear acoustic health monitoring approach for detecting loose bolts", J. Nondestr. Eval., 37(2), 24. https://doi.org/10.1007/s10921-018-0478-0
  4. Beena, K., Shruti, S., Sandeep, S. and Naveen, K. (2017), "Monitoring degradation in concrete filled steel tubular sections using guided waves", Smart Struct. Syst., Int. J., 19(4), 371-382. https://doi.org/10.12989/sss.2017.19.4.371
  5. Biwa, S., Nakajima, S. and Ohno, N. (2004), "On the acoustic nonlinearity of solid-solid contact with pressure-dependent interface stiffness", J. Appl. Mech.-Transact. ASME, 71(4), 508-515. https://doi.org/10.1115/1.1767169
  6. Caccese, V., Mewer, R. and Vel, S.S. (2004), "Detection of bolt load loss in hybrid composite/metal bolted connections", Eng. Struct., 26(7), 895-906. https://doi.org/10.1016/j.engstruct.2004.02.008
  7. Cha, Y.J., You, K. and Choi, W. (2016), "Vision-based detection of loosened bolts using the Hough transform and support vector machines", Automat. Constr., 71, 181-188. https://doi.org/10.1016/j.autcon.2016.06.008
  8. Chen, D.D, Huo, L.S. and Song, G.B. (2020), "EMI based multibolt looseness detection using series parallel multi-sensing technique", Smart Struct. Syst., Int. J., 25(4), 423-432. https://doi.org/10.12989/sss.2020.25.4.423
  9. Chung, J. and Sohn, H. (2020), "Detection and quantification of bolt loosening using RGB-D camera and mask R-CNN", Smart Struct. Syst., Int. J., 27(5), 783-793. https://doi.org/10.12989/sss.2021.27.5.783
  10. Drenick, R.F., Wang, P.C., Yun, C.B. and Philappacopoulos, A.J. (1980), "Critical seismic response of nuclear reactors", Nuclear Eng. Des., 58(3), 425-435. https://doi.org/10.1016/0029-5493(80)90155-7
  11. Fan, Z. and Lowe, M.J.S. (2009), "Elastic waves guided by a welded joint in a plate", Proceedings of the Royal Society AMathematical Physical & Engineering Sciences, 465(2107), 2053-2068. https://doi.org/10.1098/rspa.2009.0010
  12. Fasel, T.R., Kennel, M.B., Todd, M.D., Clayton, E.H. and Park, G. (2009), "Damage state evaluation of experimental and simulated bolted joints using chaotic ultrasonic waves", Smart Struct. Syst., Int. J., 5(4), 329-344. https://doi.org/10.12989/sss.2009.5.4.329
  13. Fink, M., Cassereau, D., Derode, A., Prada, C., Roux, P., Tanter, M., Thomas, J.L. and Wu, F. (2000), "Time-reversed acoustic", Reports on Progress Phys., 63(12), 1933-1995. https://doi.org/10.1088/0034-4885/63/12/202
  14. GB 50205 (2020), Standard for acceptance of construction quality of steel structures, China Planning Press, Beijing.
  15. Gianesini, B.M., Cortez, N.E., Antunes, R.A. and Vieira, J. (2020), "Method for removing temperature effect in impedance-based structural health monitoring systems using polynomial regression", Struct. Health Monitor., 20(1), 202-218. https://doi.org/10.1177/1475921720917126
  16. Hayashi, T. and Murase, M. (2005), "Defect imaging with guided waves in a pipe", J. Acoust. Soc. Am., 117(4), 2134-2140. https://doi.org/10.1121/1.1862572
  17. Huda, F., Kajiwara, I., Hosoya, N. and Kawamura, S. (2013), "Bolt loosening analysis and diagnosis by non-contact laser excitation vibration tests", Mech. Syst. Signal Process., 40(2), 589-604. https://doi.org/10.1016/j.ymssp.2013.05.023
  18. Hush, D.R. and Horne, B.G. (1993), "Progress in supervised neural networks", IEEE Signal Process. Magaz., 10(1), 8-39. https://doi.org/10.1109/79.180705
  19. Jhang, K.Y., Quan, H.H., Ha, J. and Kim, N.Y. (2006), "Estimation of clamping force in high-tension bolts through ultrasonic velocity measurement", Ultrasonics, 44, e1339-e1342. https://doi.org/10.1016/j.ultras.2006.05.190
  20. Kamas, T., Poddar, B., Lin, B. and Yu, L.Y. (2015), "Assessment of temperature effect in structural health monitoring with piezoelectric wafer active sensors", Smart Struct. Syst., Int. J., 16(5), 835-851. https://doi.org/10.12989/sss.2015.16.5.835
  21. Kubrusly, A.C. and Dixon, S. (2021), "Application of the reciprocity principle to evaluation of mode-converted scattered shear horizontal (SH) wavefields in tapered thinning plates", Ultrasonics, 117, 106544. https://doi.org/10.1016/j.ultras.2021.106544
  22. Liang, C., Sun, F.P. and Rogers, C.A. (1997), "Coupled electromechanical analysis of adaptive material systems determination of the actuator power consumption and system energy transfer", J. Intell. Mater. Syst. Struct., 5(1), 12-20. https://doi.org/10.1177/1045389X9700800406
  23. Lopes, V., Park, G., Cudney, H.H. and Inman, D.J. (2000), "Impedance-based structural health monitoring with artificial neural networks", J. Intell. Mater. Syst. Struct., 11(3), 206-214. https://doi.org/10.1106/H0EV-7PWM-QYHW-E7VF
  24. Miao, H.C. and Li, F.X. (2021), "Shear horizontal wave transducers for structural health monitoring and nondestructive testing: A review", Ultrasonics, 114, 106355. https://doi.org/10.1016/j.ultras.2021.106355
  25. Min, J., Park, S., Yun, C.B., Lee, C.G. and Lee, C. (2012), "Impedance-based structural health monitoring incorporating neural network technique for identification of damage type and severity", Eng. Struct., 39, 210-220. https://doi.org/10.1016/j.engstruct.2012.01.012
  26. Moustakidis, S., Kappatos, V., Karlsson, P., Selcuk, C., Gan, T.H. and Hrissagis, K. (2014), "An intelligent methodology for railways monitoring using ultrasonic guided waves", J. Nondestr. Eval., 33(4), 694-710. https://doi.org/10.1007/s10921-014-0264-6
  27. Na, S. and Lee, H.K. (2012), "Resonant frequency range utilized electro-mechanical impedance method for damage detection performance enhancement on composite structures", Compos. Struct., 94(8), 2383-2389. https://doi.org/10.1016/j.compstruct.2012.02.022
  28. Nikravesh, S.M.Y. and Goudarzi, M. (2017), "A review paper on looseness detection methods in bolted structures", Latin Am. J. Solids Struct., 14(12), 2153-2176. https://doi.org/10.1590/1679-78254231
  29. Pai, N.G. and Hess, D.P. (2002), "Experimental study of loosening of threaded fasteners due to dynamic shear loads", J. Sound Vib., 253(3), 585-602. https://doi.org/10.1006/jsvi.2001.4006
  30. Park, S., Yun, C.B., Roh, Y. and Lee, J.J. (2005), "Health monitoring of steel structures using impedance of thickness modes at PZT patches", Smart Struct. Syst., Int. J., 1(4), 339-353. https://doi.org/10.12989/sss.2005.1.4.339
  31. Park, S., Yun, C.B., Roh, Y. and Lee, J.J. (2006), "PZT-based active damage detection techniques for steel bridge components", Smart Mater. Struct., 15(4), 957-966. https://doi.org/10.1088/0964-1726/15/4/009
  32. Parvasi, S.M., Ho, S.C.M., Kong, Q.Z., Mousavi, R. and Song, G.B. (2016), "Real time bolt preload monitoring using piezoceramic transducers and time reversal technique-A numerical study with experimental verification", Smart Mater. Struct., 25(8), 085015. https://doi.org/10.1088/0964-1726/25/8/085015
  33. Pnevmatikos, N.G., Blachowski, B., Hatzigeorgiou, G.D. and Swiercz, A. (2016), "Wavelet analysis based damage localization in steel frames with bolted connections", Smart Struct. Syst., Int. J., 18(6), 1189-1202. https://doi.org/10.12989/sss.2016.18.6.1189
  34. Razi, P., Esmaeel, R.A. and Taheri, F. (2013), "Improvement of a vibration-based damage detection approach for health monitoring of bolted flange joints in pipelines", Struct. Health Monitor., 12(3), 207-224. https://doi.org/10.1177/14759217134796
  35. Su, Z.Q., Ye, L. and Lu, Y. (2006), "Guided Lamb waves for identification of damage in composite structures: A review", J. Sound Vib., 295(3-5), 753-780. https://doi.org/10.1016/j.jsv.2006.01.020
  36. Tang, Z.F., Sui, X.D., Duan, Y.F., Zhang, P.F. and Yun, C.B. (2021), "Guided wave-based cable damage detection using wave energy transmission and reflection", Struct. Control Health Monitor., 28(5), e2688. https://doi.org/10.1002/stc.2688
  37. Yang, J., Liu, P., Yang, S., Lee, H. and Sohn, H. (2015), "Laser based impedance measurement for pipe corrosion and boltloosening detection", Smart Struct. Syst., Int. J., 15(1), 41-55. https://doi.org/10.12989/sss.2015.15.1.041
  38. Zhang, Z., Xu, H., Liao, Y., Su, Z. and Xiao, Y. (2017), "Vibroacoustic modulation (VAM)-inspired structural integrity monitoring and its applications to bolted composite joints", Compos. Struct., 176, 505-515. https://doi.org/10.1016/j.compstruct.2017.05.043
  39. Zhang, Y., Li, D.S. and Zheng, X.T. (2019), "Detection and location of bolt group looseness using ultrasonic guided wave", Smart Struct. Syst., Int. J., 24(3), 293-301. https://doi.org/10.12989/sss.2019.24.3.293
  40. Zhang, M.R., Tang, Z.F., Yun, C.B., Sui, X.D., Chen, J. and Duan, Y.F. (2021), "Bolt looseness detection using SH guided wave and wave energy transmission", Smart Mater. Struct., 30(10), 105015. https://doi.org/10.1088/1361-665X/ac1d90
  41. Zhou, Z.H. (2016), Machine Learning, Tsinghua University Press, China, Beijing.