DOI QR코드

DOI QR Code

Tensile capacity of mortar-filled rectangular tube with various connection details

  • Kim, Chul-Goo (Department of Architectural and Urban Systems Engineering, Ewha Womans University) ;
  • Kang, Su-Min (School of Architecture, Soongsil University) ;
  • Eom, Tae-Sung (Department of Architectural Engineering, Dankook University) ;
  • Baek, Jang-Woon (Department of Architectural Engineering, Kyung Hee University)
  • Received : 2022.02.21
  • Accepted : 2022.07.28
  • Published : 2022.08.10

Abstract

A mortar-filled rectangular hollow structural section (RHS) can increase a structural section property as well as a compressive buckling capacity of a RHS member. In this study, the tensile performance of newly developed mortar-filled RHS members was experimentally evaluated with various connection details. The major test parameters were the type of end connections, the thickness of cap plates and shear plates, the use of stud bolts, and penetrating bars. The test results showed that the welded T-end connection experienced a brittle weld fracture at the welded connection, whereas the tensile performance of the T-end connection was improved by additional stud bolts inserted into the mortar within the RHS tube. For the end connection using shear plates and penetrating stud bolts, ductile behavior of the RHS tube was achieved after yielding. The penetrating bars increased load carrying capacity of the RHS. Based on the analysis of the load transfer mechanism, the current design code and test results were compared to evaluate the tensile capacity of the RHS tube according to the connection details. Design considerations for the connections of the mortar-filled RHS tubes were also recommended.

Keywords

Acknowledgement

The research in this paper was financially supported by the Korean Research Foundation (NRF-2020R1F1A1049971 and NRF-2022R1F1A1068417) as a source of government funding.

References

  1. AISC 360-16 (2016), Specification for Structural Steel Buildings, American Institute of Steel Construction; Chicago, IL, USA.
  2. Aslani, F., Uy, B., Tao, Z. and Mashiri, F. (2015), "Predicting the axial load capacity of high-strength concrete filled steel tubular columns", Steel Comp. Struct., 19(4), 967-993. https://doi.org/10.12989/scs.2015.19.4.967.
  3. Aslani, F., Uy, B., Wang, Z. and Patel, V. (2016), "Confinement models for high strength short square and rectangular concretefilled steel tubular columns", Steel Comp. Struct., 22(5), 937- 974. https://doi.org/10.12989/scs.2016.22.5.937.
  4. ASTM C39 (2020), Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens: ASTM C39 / C39M-20, ASTM International, West Conshohocken, PA, USA.
  5. ASTM E8 (2021), Standard Test Methods for Tension Testing of Metallic Materials: ASTM E8/E8M-21, ASTM International, West Conshohocken, PA, USA.
  6. Chan, S. and Fong, M. (2011), "Experimental and analytical investigations of steel and composite trusses", Advanced Steel Construct., 7(1), 17-26, https://doi.org/10.18057/IJASC.2011.7.1.2.
  7. EN ISO 15614-11:2002 (2002), Specification and Qualification of Welding Procedures for Metallic Materials - Welding Procedure Test - Part 11: Electron and laser beam welding (ISO 15614-11:2002), European Committee for Standardization; Brussels, Belgium.
  8. Fong, M., Chan, S.L. and Uy, B. (2011), "Advanced design for trusses of steel and concrete-filled tubular sections", Eng. Struct., 33(12), 3162-3171. https://doi.org/10.1016/j.engstruct.2011.08.002.
  9. Gardner, L. and Chan, T.M. (2007), "Cross-section classification of elliptical hollow sections", Steel Comp. Struct., 7(3), 185. https://doi.org/10.12989/scs.2007.7.3.185.
  10. Haddad, M., Brown, T. and Shrive, N. (2011), "Experimental cyclic loading of concentric HSS braces", Canadian J. Civil Eng., 38(1), 110-123. https://doi.org/10.1139/L10-113.
  11. Han, L.-H., Zhao, X.-L. and Tao, Z. (2001), "Tests and mechanics model for concrete-filled SHS stub columns, columns and beam-columns", Steel Comp. Struct., 1(1), 51-74. https://doi.org/10.12989/scs.2001.1.1.051.
  12. Kim, C.-G., Eom, T.-S. and Kang, S.-M. (2021), "Compressive tests of mortar-filled small rectangular hollow section members for long-span roof trusses", J. Korea Concrete Institute, 33(4), 343-351. https://doi.org/10.4334/JKCI.2021.33.4.343.
  13. Kitipornchai, S., Al-Bermani, F. and Chan, S.L. (1988), "Geometric and material nonlinear analysis of structures comprising rectangular hollow sections", Eng. Struct., 10(1), 13-23. https://doi.org/10.1016/0141-0296(88)90012-0.
  14. Kitipornchai, S. and Traves, W. (1986), Design of Cap-Cleat Plate End Connections for Tubes, Research Report No. CE68 c; Department of Civil Engineering, The University of Queensland, Brisbane, Australia.
  15. Kitlpornchai, S. and Traves, W.H. (1989), "Welded-Tee End Connections for Circular Hollow Tubes", J. Struct. Eng., 115(12), 3155-3170. https://doi.org/10.1061/(ASCE)0733-9445(1989)115:12(3155).
  16. KSD 3515 (2018), Rolled Steels for Welded Structures (in Korean), Korean Agency for Technology and Standards, Seoul, Republic of Korea.
  17. KSD 3568 (2018), Carbon Steel Square Pipes for General Structural Purposes (in Korean), Korean Agency for Technology and Standards; Seoul, Republic of Korea.
  18. KSD 3504 (2021), Steel Bars for Concrete Reinforcement (in Korean), Korean Agency for Technology and Standards, Seoul, Republic of Korea.
  19. Korol, R. (1996), "Shear lag in slotted HSS tension members", Canadian J. Civil Eng., 23(6), 1350-1354. https://doi.org/10.1139/l96-943.
  20. Lam, D. and Williams, C.A. (2004), "Experimental study on concrete filled square hollow sections", Steel Comp. Struct., 4(2), 95-112. https://doi.org/10.12989/scs.2004.4.2.095.
  21. Ling, T.W., Zhao, X.L., Al-Mahaidi, R. and Packer, J.A. (2007), "Investigation of shear lag failure in gusset-plate welded structural steel hollow section connections", J. Constr. Steel. Res., 63(3), 293-304. https://doi.org/10.1016/j.jcsr.2006.05.006.
  22. Nasce, V. and Tondolo, F. (2010), "Tensile behavior of welded tee end connection for circular hollow members", Adv. Steel Construct., 6(4), 1034-1047. https://doi.org/10.18057/IJASC.2010.6.4.7.
  23. Packer, J., Sherman, D. and Lecce, M. (2010), Steel Design Guide 24: Hollow Structural Section Connections, American Institute of Steel Construction, Chicago, IL, USA.
  24. Packer, J.A., Wardenier, J., Zhao, X.-L., Van der Vegte, G. and Kurobane, Y. (2009), Design Guide for Rectangular Hollow Section (RHS) Joints under Predominantly Static Loading, Cidect, Genova, Switzerland.
  25. Saidani, M. (2008), "Behaviour of welded T-end connection to rectangular hollow section (RHS) in axial tension", J. Constr. Steel. Res., 64(4), 447-453. https://doi.org/10.1016/j.jcsr.2007.10.003.
  26. Saidani, M. (2011), "Experimental investigation of welded T-end connection to circular hollow section (CHS)", Eng. Sci., 6(4), 1407-1416.
  27. Saidani, M. and Omair, M. (2001), "Welded T-End connection to rectangular hollow section (RHS)", Proceedings of the 9th International Symposium and Euroconference on Tubular Structures, Dusseldorf, Germany, April.
  28. Shen, J. and Wadee, M.A. (2018a), "Imperfection sensitivity of thin-walled rectangular hollow section struts susceptible to interactive buckling", Int. J. Non. Linear. Mech., 99, 112-130. https://doi.org/10.1016/j.ijnonlinmec.2017.11.004.
  29. Shen, J. and Wadee, M.A. (2018b), "Length effects on interactive buckling in thin-walled rectangular hollow section struts", ThinWall. Struct., 128, 152-170. https://doi.org/10.1016/j.tws.2017.04.006.
  30. Shen, J. and Wadee, M.A. (2019), "Sensitivity to local imperfections in inelastic thin-walled rectangular hollow section struts", Structures, 17, 43-57, https://doi.org/10.1016/j.istruc.2018.12.006.
  31. Shen, J., Wadee, M.A. and Sadowski, A.J. (2017), "Interactive buckling in long thin-walled rectangular hollow section struts", Int. J. Non. Linear. Mech., 89, 43-58. https://doi.org/10.1016/j.ijnonlinmec.2016.11.007.
  32. Stevens, N.J. and Kitipornchai, S. (1990), "Limit analysis of welded tee end connections for hollow tubes", J. Struct. Eng., 116(9), 2309-2323. https://doi.org/10.1061/(ASCE)0733-9445(1990)116:9(2309).
  33. Wardenier, J., Kurobane, Y., Packer, J.A., Van der Vegte, G. and Zhao, X. (2008), Design Guide for Circular Hollow Section (CHS) Joints under Predominantly Static Loading, CIDECT, Genova, Switzerland.
  34. Willibald, S., Packer, J. and Martinez-Saucedo, G. (2006), "Behaviour of gusset plate connections to ends of round and elliptical hollow structural section members", Canadian J. Civil Eng., 33(4), 373-383. https://doi.org/10.1139/l05-052.
  35. Zhao, R., Huang, R., Khoo, H. and Cheng, J. (2008), "Experimental study on slotted rectangular and square hollow structural section (HSS) tension connections", Canadian J. Civil Eng., 35(11), 1318-1330. https://doi.org/10.1139/L08-069.