Structural Engineering and Mechanics

  • 제83권2호
  • /
  • Pages.195-206
  • /
  • 2022
  • /
  • 1225-4568(pISSN)
  • /
  • 1598-6217(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

A comparative study on the seismic provisions of different codes for RC buildings

  • 투고 : 2021.10.20
  • 심사 : 2022.05.02
  • 발행 : 2022.07.25
⟨ 이전 논문 다음 논문 ⟩

초록

Significant structural damages due to earthquakes reveal the importance of seismic design provisions. This paper presents a comparison between the seismic design provisions of Albania, Croatia, Iran, and Turkey for the design of mid-rise reinforced-concrete (RC) frames. Information on the historical development of the considered provisions are given. The code provisions are compared, illustrating the main differences in the minimum requirements for column and beam detailing and analysis for mid-rise RC frames. 4-story, 5-story, and 6-story buildings are designed according to each design code, and their performance is evaluated comparatively by using a displacement-based adaptive pushover procedure and eigenvalue analysis. It is observed that recent Turkish code has the highest and Albanian code has the lowest level of requirements in terms of member size and reinforcement detailing. The considered models indicate 15%, 20% and 50%, lower period values than the Croatia, Iran and Albania buildings, respectively. Additionally, building models per Croatia, Iran and Albania codes have 30%, 35% and 65% less base shear capacity when compared to Turkish building codes. Building models per Croatia and Iran codes indicate similar properties both in terms of strength and stiffness.

키워드

참고문헌

  1. Ademovic, N., Hrasnica, M. and Oliveira, D.V. (2013), "Pushover analysis and failure pattern of a typical masonry residential building in Bosnia and Herzegovina", Eng. Struct., 50, 13-29. https://doi.org/10.1016/j.engstruct.2012.11.031.
  2. Al-Tayeb, M., Zeyad, A., Dawoud, O. and Tayeh, B.A. (2021), "Experimental and numerical investigations of the influence of partial replacement of coarse aggregates by plastic waste on the impact load", Int. J. Sustain. Eng., 14(4), 735-742. https://doi.org/10.1080/19397038.2020.1774820.
  3. Aliaj, S., Adams, J., Halchuk, S., Sulstarova, E., Peci, V. and Muco, B. (2004), "Probabilistic seismic hazard maps for Albania", 13th World Conference on Earthquake Engineering, Paper No: 2469, Vancouver, BC, Canada
  4. Aliaj, S., Kociu, S., Muco, B. and Sulstarova, E (2010), "Seismicity, seismotectonics and the seismic hazard assessment in Albania", Albanian Academy of Sciences, Tirana, Albania.
  5. Alshaikh, I.M., Bakar, B.A., Alwesabi, E.A., Zeyad, A.M. and Magbool, H.M. (2021), "Finite element analysis and experimental validation of progressive collapse of reinforced rubberized concrete frame", Struct., 33, 2361-2373. https://doi.org/10.1016/j.istruc.2021.06.008.
  6. Alwesabi, E.A., Bakar, B.A., Alshaikh, I.M., Zeyad, A.M., Altheeb, A. and Alghamdi, H. (2021), "Experimental investigation on fracture characteristics of plain and rubberized concrete containing hybrid steel-polypropylene fiber", Struct., 33, 4421-4432. https://doi.org/10.1016/j.istruc.2021.07.011.
  7. Alyamac, K.E. and Erdogan, A.S. (2005), "Gecmisten gunumuze afet yonetmelikleri ve uygulamada karsilasilan tasarim hatalari", Deprem Sempozyumu, Kocaeli, 707-715.
  8. Antoniou, S. and Pinho, R. (2003), "Seismostruct-seismic analysis program by Seismosoft", Technical Manual and User Manual.
  9. Antoniou, S. and Pinho, R. (2004a), "Advantages and limitations of adaptive and non-adaptive force-based pushover procedures", J. Earthq. Eng., 8(4), 497-522. https://doi.org/10.1142/S1363246904001511.
  10. Antoniou, S.and Pinho, R. (2004b), "Development and verification of a displacement-based adaptive pushover procedure", J. Earthq. Eng., 8(5), 643-661. https://doi.org/10.1142/S136324690400150X.
  11. Belejo, A. and Bento, R. (2012), "Influence of modelling issues on nonlinear static seismic analysis of a regular 3D steel structure", ICIS Report, Portugal.
  12. BHRC (2019), Iranian Code of Practice for Seismic Resistant Design of Buildings, Standard No. 2800, Building& Housing Research Center, Tehran, Iran.
  13. Bilgin, H. and Hysenlliu, M. (2020), "Comparison of near and far-fault ground motion effects on low and mid-rise masonry buildings", J. Build. Eng., 30, 101248, https://doi.org/10.1016/j.jobe.2020.101248.
  14. Bulajic, B.D., Todorovska, M.I., Manic, M.I. and Trifunac, M.D. (2020), "Structural health monitoring study of the ZOIL building using earthquake records", Soil Dyn. Earthq. Eng., 133, 106105. https://doi.org/10.1016/j.soildyn.2020.106105.
  15. Cademartori, M., Sullivan, T.J. and Osmani, S. (2020), "Displacement based assessment of typical Italian RC bridges", B. Earthq. Eng., 18, 4299-4329. https://doi.org/10.1007/s10518-020-00861-9.
  16. Caglar, N., Demir, A., Ozturk, H. and Akkaya, A. (2015), "A simple formulation for effective flexural stiffness of circular reinforced concrete columns", Eng. Appl. Artif. Intel., 38, 79-87. https://doi.org/10.1016/j.engappai.2014.10.011.
  17. Crowley, H., Despotaki, V., Silva, V., Dabbeek, J., Romao, X., Pereira, N., ... & Hancilar, U. (2021), "Model of seismic design lateral force levels for the existing reinforced concrete European building stock", Bull. Earthq. Eng., 19, 2839-2865. https://doi.org/10.1007/s10518-021-01083-3.
  18. Duni, L., Kuka, N., Kuka, S. and Fundo, A. (2010), "Towards a new seismic hazard assessment of Albania", Proc. of 14 ECEE, Ohrid, Fyrom.
  19. Estevao, J.M. and Oliveira, C.S. (2015), "A new analysis method for structural failure evaluation", Eng. Fail. Anal., 56, 573-584. https://doi.org/10.1016/j.engfailanal.2014.08.009.
  20. Eurocode, C.E.N. (2005), Eurocode-8: Design of Structures for Earthquake Resistance-Part 3: Assessment and Retrofitting of Buildings, EN1998-3, European Committee for Standardization, Bruxelles, Belgium.
  21. Hadzima-Nyarko, M. and Kalman Sipos, T. (2017), "Insights from existing earthquake loss assessment research in Croatia", Earthq. Struct., 13(4), 365-375. https://doi.org/10.12989/eas.2017.13.4.365.
  22. Hadzima-Nyarko, M., Moric, D., Draganic, H. and Stefic, T. (2015), "Comparison of fundamental periods of reinforced shear wall dominant building models with empirical expressions", Techn. Gazette, 22(3), 685-694. https://doi.org/10.17559/TV20140228124615.
  23. Hadzima-Nyarko, M., Pavic, G. and Lesic, M. (2016), "Seismic vulnerability of older confined masonry buildings in Osijek, Croatia", Earthq. Struct., 11(4), 629-648. http://doi.org/10.12989/eas.2016.11.4.629.
  24. Hysenlliu, M., Bidaj, A. and Bilgin, H. (2020), "Influence of material properties on the seismic response of masonry buildings", Res. Eng. Struct. Mater., 6(4), 425-437. http://doi.org/10.17515/resm2020.177st0120.
  25. Inel, M., Bilgin, H. and Ozmen, H.B. (2008), "Performance of mid-rise reinforced concrete buildings during recent earthquakes in Turkey", Teknik Dergi, 19(91), 4319-4331.
  26. Isik, E. (2020), "Advances in earthquake codes in terms of structural performance: Case of Turkey", Unpublished Article.
  27. Isik, E., Aydin, M.C. and Buyuksarac, A. (2020), "24 January 2020 Sivrice (Elazig) earthquake damages and determination of earthquake parameters in the region", Earthq. Struct., 19(2), 145-156. https://doi.org/10.12989/eas.2020.19.2.145.
  28. Isik, E., Isik, M.F. and Bulbul, M.A. (2017), "Web based evaluation of earthquake damages for reinforced concrete buildings", Earthq. Struct., 13(4), 387-396. https://doi.org/10.12989/eas.2017.13.4.387.
  29. Kemaloglu, M. (2015), "Historical and legal development of disaster management in Turkey", Akademik Bakis Dergisi, 5, 126-147.
  30. KTP-9-78 (1978), Albanian Masonry Design Code.
  31. KTP-N2-89 (1989), Albanian Seismic Design Code.
  32. Kuka, N., Duni, L., Aliaj, S. and Sulstarova, E.(2003), "Seismic hazard assessment of Albania by spatially smoothed seismicity approach", International Conference on Earthquake Engineering, Ohrid, FYROM.
  33. Kutanis, M. (2006), "Statik itme analizi yontemlerinin performanslarinin degerlendirilmesi", Yapisal Onarim ve Guclendirme Sempozyumu, YOGS2006 Bildiriler Kitabi, 205-210.
  34. Kutanis, M., Ulutas, H. and Isik, E. (2018), "PSHA of Van province for performance assessment using spectrumlly matched strong ground motion records", J. Earthq. Syst. Sci., 127(7), 99. https://doi.org/10.1007/s12040-018-1004-6.
  35. Leti, M. and Bilgin, H. (2022), "Damage potential of near and farfault ground motions on seismic response of RC buildings designed according to old practices", Res. Eng. Struct. Mater., 8(2), 337. http://doi.org/10.17515/resm2022.392ea0123.
  36. Luo, Y.F., Liu, Y.P., Hu, Z.Y. and Xiong, Z. (2017), "A new method for dynamic analysis of spatial lattice structures based on mode selection and mode construction techniques", Int. J. Steel Struct., 17(3), 1157-1170. https://doi.org/10.1007/s13296-017-9023-8.
  37. Magbool, H.M. and Zeyad, A.M. (2021), "The effect of various steel fibers and volcanic pumice powder on fracture characteristics of Self-Compacting concrete", Constr. Build. Mater., 312, 125444. https://doi.org/10.1016/j.conbuildmat.2021.125444.
  38. Muco, B., Vaccari, F., Panza, G. and Kuka, N. (2002), "Seismic zonation in Albania using a deterministic approach", Tectonophys., 344(3-4), 277-288. https://doi.org/10.1016/S0040-1951(01)00279-7.
  39. Nikoo, M., Hadzima-Nyarko, M., Khademi, F. and Mohasseb, S. (2017), "Estimation of fundamental period of reinforced concrete shear wall buildings using self organization feature map", Struct. Eng. Mech., 63(2), 237-249. https://doi.org/10.12989/sem.2017.63.2.237.
  40. ONBR (2009), "National buildingregulations, Part 9: Design and construction of RC buildings", Office of National Building Regulations, Tehran, Iran
  41. Ozmen, H.B. and Inel, M. (2016), "Damage potential of earthquake records for RC building stock", Earthq. Struct., 10(6), 1315-1330. https://doi.org/10.12989/eas.2016.10.6.1315.
  42. Ozmen, H.B., Inel, M., Akyol, E., Cayci, B.T. and Un, H. (2014), "Evaluations on the relation of RC building damages with structural parameters after May 19, 2011 Simav (Turkey) earthquake", Nat. Hazard., 71(1), 63-84. https://doi.org/10.1007/s11069-013-0900-y.
  43. Ozmen, H.B., Yilmaz, H. and Yildiz, H. (2019), "An acceleration record set for different frequency content, amplitude and site classes", Res. Eng. Struct. Mater, 5(3), 321-333. http://doi.org/10.17515/resm2019.116ea0209ds.
  44. Ozturk, M. (2018), "An evaluation about 2018 Turkey Building Earthquake Regulations and Turkey earthquake hazards map based on Central Anatolia Region", J. Selcuk-Technic, 17(2), 31-42.
  45. Pavic, G., Hadzima-Nyarko, M. and Bulajic, B. (2020), "A Contribution to a UHS-based Seismic Risk Assessment in Croatia-A Case Study for the City of Osijek", Sustain., 12(5), 1796. https://doi.org/10.3390/su12051796.
  46. Peci, V., Adams, J., Al-Khoubbi, I. and Halchuk, S. (2002), "Probabilistic seismic hazard maps for Albania", Book of Abstracts, Univ. of Genoa, Italy.
  47. Peres, R., Bento, R. and Castro, J.M. (2020), "Nonlinear static seismic performance assessment of plan-irregular steel structures", J. Earthq. Eng., 24(2), 226-253. https://doi.org/10.1080/13632469.2018.1469438.
  48. Pinto, P.E. and Franchin, P. (2011), Eurocode 8-Part 3: Assessment and Retrofitting of Buildings, Eurocode 8 Background and Applications, Dissemination of Information for Training. Lisbon, Portugal.
  49. Seismosoft (2022), SeismoStruct 2022-A Computer Program for Static and Dynamic Nonlinear Analysis of Framed Structures, http://www.seismosoft.com.
  50. Shkodrani, N. and Bilgin H. (2021), "Seismic performance of existing low-rise URM buildings considering the addition of new stories", Struct. Eng. Mech., 79(6), 767-777. https://doi.org/10.12989/sem.2021.79.6.767.
  51. Shkodrani, N., Bilgin, H. and Hysenlliu, M. (2021), "Influence of interventions on the seismic performance of URM buildings designed according to pre-modern codes", J. Res. Eng. Struct. Mater., 7(2), 315-330. http://doi.org/10.17515/resm2020.197ea0331.
  52. Sofi, M., Hutchinson, G.L. and Duffield, C. (2015), "Review of techniques for predicting the fundamental period of multi-storey buildings: effects of nonstructural components", Int. J. Struct. Stab. Dyn., 15(02), 1450039. https://doi.org/10.1142/S0219455414500394.
  53. Strukar, K., Sipos, T.K., Jelec, M. and Hadzima-Nyarko, M. (2019), "Efficient damage assessment for selected earthquake records based on spectral matching", Earthq. Struct., 17(3), 271-282. https://doi.org/10.12989/eas.2019.17.3.271.
  54. Tao, D., Ma, Q., Li, S., Xie, Z., Lin, D. and Li, S. (2020), "Support vector regression for the relationships between ground motion parameters and macroseismic intensity in the Sichuan-Yunnan Region", Appl. Sci., 10(9), 3086. https://doi.org/10.3390/app10093086.
  55. Technical Regulation for Concrete Structures (NN 101/05) (2005), Newspaper-publishing Institution "Official Gazette", Zagreb, Croatia.
  56. Todorovska, M.I. and Al Rjoub, Y. (2006), "Effects of rainfall on soil-structure system frequency: Examples based on poroelasticity and a comparison with full-scale measurements", Soil Dyn. Earthq. Eng., 26(6-7), 708-717. https://doi.org/10.1016/j.soildyn.2006.01.019.
  57. Todorovska, M.I. and Al Rjoub, Y. (2009), "Environmental effects on measured structural frequencies-model prediction of short-term shift during heavy rainfall and comparison with full-scale observations", Struct. Control Hlth. Monit., 16(4), 406-424. https://doi.org/10.1002/stc.260.
  58. Trifunac, M.D., Todorovska, M.I., Manic, M.I. and Bulajic, B.D. (2010), "Variability of the fixed-base and soil- structure system frequencies of a building-The case of Borik-2 building", Struct. Control Hlth. Monit., 17(2), 120-151. https://doi.org/10.1002/stc.277.
  59. Turkey Building Earthquake Code (TBEC-2018), Ministry of Interior Disaster and Emergency Management Presidency, Ankara, Turkey.
  60. Ugalde, D., Lopez-Garcia, D. and Parra, P.F. (2020), "Fragility-based analysis of the influence of effective stiffness of reinforced concrete members in shear wall buildings", Bull. Earthq. Eng., 18(5), 2061-2082. https://doi.org/10.1007/s10518-020-00786-3.
  61. Wilding, B.V. and Beyer, K. (2018), "The effective stiffness of modern unreinforced masonry walls", Earthq. Eng. Struct. Dyn., 47(8), 1683-1705. https://doi.org/10.1002/eqe.3035.
  62. Xian, L., He, Z. and Ou, X. (2016), "Incorporation of collapse safety margin into direct earthquake loss estimate", Earthq. Struct., 10(2), 429-450. https://doi.org/10.12989/eas.2016.10.2.429.
  63. Yakut, A., Erberik, M.A., Ilki, A., Sucuoglu, H. and Akkar, S. (2014), "Rapid seismic assessment procedures for the Turkish Building Stock", Seis. Eval. Rehab. Struct., 15-35. https://doi.org/10.1007/978-3-319-00458-7_2.