한국가스학회지 (Journal of the Korean Institute of Gas)

  • 제26권2호
  • /
  • Pages.21-26
  • /
  • 2022
  • /
  • 1226-8402(pISSN)
  • /
  • 2713-6922(eISSN)
한국가스학회 (The Korean Institute of GAS)
권호 표지
DOI QR코드

DOI QR Code

Transfer case의 구동변환을 위한 유성기어장치 구동부 설계

Design of Planetary Gear Drive Unit for Drive Conversion of Transfer case

  • 염광욱 (한양사이버대학교 기계자동차공학부)
  • Youm, Kwang-Wook (Dept. of Mechanical and Automotive Engineering, Hanyang Cyber University)
  • 투고 : 2022.03.28
  • 심사 : 2022.04.12
  • 발행 : 2022.04.30
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

사륜구동은 구동력을 4바퀴에 모두 전달하기 때문에 노면과의 접지력이 상승하여 구동력이 상승한다. 하지만 그로 인해 연비가 저하되는 단점을 가지고 있다. 따라서 평소에 이륜구동으로 주행하다가 필요에 의해 선택적 사륜구동으로 변환하는 방법으로 사륜구동을 많이 사용한다. 이러한 선택적 사륜구동은 운전자가 보내는 전기적 신호를 Transfer case에서 기계적으로 바꿔서 구동력을 변환시킨다. 본 연구에서는 전기적 신호를 기계적으로 바꿔주기 위해 모터에 감속기를 적용하여 토크를 증대시켜 기능을 수행하였다. 따라서, 본 연구에서는 구동을 변환시켜주기 위해 적용되는 Transfer case내부에 있는 모터에 적용할 수 있는 감속메커니즘을 도출하고 그에 따른 유성기어형태를 적용한 감속비를 최적화하였다. 그리고 도출된 감속비를 토대로 링기어를 공통으로 사용하는 유성기어 2세트를 적용하여 입력축과 출력축이 동일상에서 감속이 진행되는 유성기어 기어치형의 개발 및 Transfer csae 내에 있는 구동변환장치 구동부의 최적화 설계를 진행하였다.

Since the four-wheel drive transmits the driving force to all four wheels, the traction with the road surface increases, thereby increasing the driving force. However, it has the disadvantage of lowering fuel efficiency. Therefore, four-wheel drive is commonly used as a method of converting to optional four-wheel drive when necessary while driving in two-wheel drive. This selective four-wheel drive converts the driving force by mechanically changing the electric signal sent by the driver in the transfer case. In this study, in order to mechanically change the electrical signal, a reducer is applied to the motor to increase the torque to perform the function. Therefore, in this study, a reduction mechanism applicable to the motor inside the transfer case applied to convert the drive is derived, and the reduction ratio applying the planetary gear type is optimized accordingly. And based on the derived reduction ratio, two sets of planetary gears using a ring gear in common were applied to develop a planetary gear tooth type in which the input shaft and output shaft are decelerated in the same phase. Optimization design was carried out.

키워드

참고문헌

  1. Kim, M. H., Qin, Z., Lee, K. H., Zhang, Q., and Lyu, S. K., "A Study on the Design of Rear Wheel Drive Reducer for Electric Vehicle", Journal of the Korean Society for Precision Engineering, 35(6), 571-577, (2018) https://doi.org/10.7736/kspe.2018.35.6.571
  2. Kwon, H. S., "Assemblability Analysis of Kinematic Configurations of Front-Wheel Drive Automatic Transmissions" Journal of the Korean Society of Manufacturing Process Engineers, 18(11), 24-34, (2019) https://doi.org/10.14775/ksmpe.2019.18.11.024
  3. Jeong, J. R., Kim, H. K., Kim, K. Y., Lim, W. S., and Cha, S. W., "Evaluation of Fuel Economy and Performance for 2WD and 4WD Hybrid Electric Vehicle Based on Backward Simulation", Transactions of KSAE, 22(1) 174-182, (2014)
  4. Kim, Y. D., "Driveline Vibration Reduction of FR (front engine rear wheel drive) Vehicle at Rapid Acceleration", Trans. Korean Soc. Noise Vib. Eng, 24(8) 592-599, (2014)
  5. Kim, H. D., and Choi, G. J., "Integrated Chassis Control System of a Rear In-wheel Motor Vehicle", Transactions of KSAE, 24(4) 439-446, (2016) https://doi.org/10.7467/KSAE.2016.24.4.439
  6. Han, K. S., and Park, G. S., "Lateral Motion Control of Electronic-Four-Wheel Drive Vehicles for Enhancement of Cornering Performance", Transactions of KSAE, 28(9), (2020)
  7. Kwon, J. H., and Oh T. L., "An Experimental Study on a Full Time Four Wheel Drive Vehicle", Transactions of KSAE, 7(2), 242-252, (1999)
  8. Jang, J. H., Kim, C. J., Kim, S. H., Kang, M. S., Back, S. H., Kim, Y. S., and Han, C. S., "Improvement of the Yaw Motion for Electric Vehicle Using Independent Front Wheel Steering and Four Wheel Driving", Journal of Institute of Control, Robotics and Systems, 19(1) 45-55, (2013) https://doi.org/10.5302/J.ICROS.2013.19.1.045
  9. Cho, H. D., "Development of Loader with Four Wheel Driving and Four-Type Wheel Steering System", Journal of the Korean Society of Manufacturing Process Engineers, 3(3), 71-7849, (2004)
  10. Kim, J. A., and Jun, J. U., "A Study on the Development of Limited Slip Differential on All Terrain Vehicle", Journal of the Korean Society of Manufacturing Process Engineers, 10(1), 8-15, (2011)
  11. Kim, J. G., Park, Y. J., Lee, G. H., Oh, J. Y., and Kim, Y. J., "A Study on the Load Sharing among Planet Gears according to the Phase of Carrier Pinhole Position Error in the Planetary Gearbox", Journal of the Korean Society for Precision Engineering, 34(6), 377-382, (2017) https://doi.org/10.7736/KSPE.2017.34.6.377
  12. Bae, M. H., Bae, T. Y., Cho, Y. S., Son, H. Y., and Kim, D. J., "The Stress Analysis of Planetary Gear System of Mixer Reducer for Concrete Mixer Truck", Journal of Drive and Control, 12(4), 77-81, (2015) https://doi.org/10.7839/KSFC.2015.12.4.077
  13. Youm, K. W., "Study on the Shift Characteristics of a 2speed Manual Transmission apply to V-Blet", KIGAS, 24(6), 55-60, (2020)
  14. Sim, K. J., Moon, H. J., Choi, G. J., Koh, S. K., and Jeon, N. J., "Bending Stress Analysis of the Transfer Case Helical Gear for the 3.5 Ton Commercial Vehicle", Transactions of KSAE, 25(4), 474-480, (2017) https://doi.org/10.7467/KSAE.2017.25.4.474
  15. Lee, W. K., and Park, S. M., "A Study on the Embodiment of a Transfer Case with High-Speed Reduction of the Planetary Gear Type Applied to Big Industrial Vehicles", Journal of the Korean Society of Manufacturing Process Engineers, 14(6), 14-20, (2015)