DOI QR코드

DOI QR Code

Z-source 직류 차단기의 기계식 스위치 적용을 위한 최적화 설계

Optimization Design for the Use of Mechanical Switch in Z-source DC Circuit Breaker

  • 이현승 (한경대학교 사회안전시스템공학과) ;
  • 이건아 (한경대학교 사회안전시스템공학과)
  • Lee, Hyeon Seung (School of Social Safety System Engineering, Hankyong National University) ;
  • Lee, Kun-A (School of Social Safety System Engineering, Hankyong National University)
  • 투고 : 2021.10.19
  • 심사 : 2022.01.19
  • 발행 : 2022.02.28

초록

Circuit breakers are a crucial factor in ensuring the safety of a Direct Current (DC) grid. One type of DC circuit breaker, the Z-source DC circuit breaker (ZCB), uses a thyristor, which is a type of semiconductor switch. In the event of a fault in the circuit, the ZCB isolates the fault by generating a zero crossing current in the thyristor. The thyristor quickly and actively isolates the fault while generating a zero crossing current, but thyristor switch cannot control turn-off and the allowable current is lower than the current of the mechanical switch. Therefore, it is best to use a mechanical switch with a high allowable current capacity that is capable of on/off control. Due to the slow reaction time of mechanical switches, they may not isolate the fault during the zero crossing current time interval created by the existing circuit. In this case, the zero crossing current time can be increased by using the property that hinders the rapid change in the current of the inductor. This paper will explore whether adding system inductance to increase the zero crossing current time interval is a solution to this problem. The simulation of changing inductor and capacitor (LC) of the circuit is repeated to find an optimal change in the zero crossing current time according to the LC change and provides an inductor and capacitor range optimized for a specific load. The inductor and capacitor range are expected to provide optimization information in the form LC values for future applications of ZCB's using a mechanical switch.

키워드

과제정보

This research was supported by Hankyong National University Development Project Research Fund, 2021.

참고문헌

  1. J. J. Justo, F. Mwasilu and J. Lee, "AC Microgrids Versus DC Microgrids with Distributed Energy Resources: A Review", Renew. Sustain. Energy Rev., Vol. 24, pp. 387-405, 2013. https://doi.org/10.1016/j.rser.2013.03.067
  2. M. R. Starke, L. M. Tolbert and B. Ozpineci, "Ac vs. Dc Distribution: A loss comparison", Proc. IEEE/PES Transm. Distrib. Conf. Exposition, pp. 1-7, 2008.
  3. H. S. Choi, "Status of Development of Hvdc System and DC Circuit Breaker Technology", The World of Electricity., Vol. 65, pp. 21-27, 2016.
  4. Z. Ganhao, "Study on DC circuit breaker", Intelligent Systems Design and Engineering Applications (ISDEA) 2014 Fifth International Conference on, pp. 942-945, 2014.
  5. M.. Barnes, D. S. Vilchis-Rodriguez, X. Pei, R. Shuttleworth, O. Cwikowski & AC. Smith., "HVDC Circuit Breakers-A Review", IEEE Access, Vol. 8, pp. 211829-211848, 2020. https://doi.org/10.1109/ACCESS.2020.3039921
  6. F. Z. Peng, "Z-Source Inverter", IEEE Transactions on Industry Applications, Vol. 39, No. 2, pp. 504-510, 2003. https://doi.org/10.1109/TIA.2003.808920
  7. S. Vadi, R. Bayindir and E. Hossain, "A Review of Control Methods on Suppression of 2 ω Ripple for Single-phase Quasi-Z-source Inverter", IEEE Access, Vol. 8, pp. 42055-42070, 2020. https://doi.org/10.1109/ACCESS.2020.2976581
  8. K. A. Corzine and R. W. Ashton, "A New Z-Source DC Circuit Breaker", IEEE Transactions on Power Electronics, Vol. 27, No. 6, pp. 2796-2804, 2012. https://doi.org/10.1109/TPEL.2011.2178125
  9. K. A. Corzine and R. W. Ashton, "Structure and Analysis of the Z-source MVDC Breaker", Proc. IEEE Electr. Ship Technol. Symp., pp. 334-338, 2011.
  10. D. J. Ryan, H. D. Torresan and B. Bahrani, "A bidirectional Series Z-Source Circuit Breaker", IEEE Trans. Power Electron., Vol. 33, No. 9, pp. 7609-7621, 2018. https://doi.org/10.1109/tpel.2017.2764903
  11. L. Mackey, M. R. K. Rachi, C. Peng and I. Husain, "Optimization and Control of a Z-source Ultrafast Mechanically Switched High-efficiency DC Circuit Breaker", IEEE Transactions on Industry Applications, Vol. 56, No. 3, pp. 2871-2879, 2020. https://doi.org/10.1109/tia.2020.2970657
  12. D. Keshavarzi, T. Ghanbari and E. Farjah, "A Z-source Based Bidirectional DC Circuit Breaker with Fault Current Limitation and Interruption Capabilities", IEEE Trans. Power Electron., Vol. 32, No. 9, pp. 6813-6822, 2017. https://doi.org/10.1109/TPEL.2016.2624147
  13. C. Xu et al., "Piezoelectrically Actuated Fast Mechanical Switch for MVDC Protection", IEEE Trans. Power Del, Vol. 36, pp. 2955-2964, 2020.
  14. W. Wen et al., "Research on Operating Mechanism for Ultra-fast 40.5-kV Vacuum Switches", IEEE Trans. Power Del., Vol. 30, No. 6, pp. 2553-2560, 2015. https://doi.org/10.1109/TPWRD.2015.2409122
  15. X. Li, D. Chen, Y. Wang, Q. Wang and Y. Geng, "Analysis of the Interruption Process of Molded Case Circuit Breakers", IEEE Trans. Components Packag. Technol., Vol. 30, No. 3, pp. 375-382, 2007. https://doi.org/10.1109/TCAPT.2007.900051