DOI QR코드

DOI QR Code

다공성 매질 모델 기반 출구유량 감소 모사 기법을 이용한 산업기계용 엔진룸 열유동해석

Thermal Flow Analysis of an Engine Room using a Porous Media Model for Imitating Flow Rate Reduction at Outlet of Industrial Machines

  • Choi, Yo Han (Department of Mechanical Engineering, Inha University) ;
  • Yoo, Il Hoon (Hyundai Doosan Infracore Corporation) ;
  • Lee, Chul-Hee (Department of Mechanical Engineering, Inha University)
  • 투고 : 2022.01.10
  • 심사 : 2022.02.10
  • 발행 : 2022.03.01

초록

Considering the characteristics of industrial machines that lack vehicle-induced wind, forced convection by a cooling fan is mostly required. Therefore, numerical analysis of an engine room is usually performed to examine the cooling performance in the room. However, most engine rooms consist of a number of parts and components at specific positions, leading to high costs for numerical modeling and simulation. In this paper, a new methodology for three-dimensional computer-assisted design simplification was proposed, especially for the pile of components and parts at the engine room outlet. A porous media model and regression analysis were used to derive a meta-model for imitating the flow rate reduction at the outlet by the pile. The results showed that the fitted model was reasonable considering the coefficient of determination. The final numerical model of the engine room was then used to simulate the velocity distribution by changing the mass flow rate at the outlet. The results showed that both velocity distributions were significantly changed in each case and the meta-model was valid in imitating the flow rate reduction by some piles of components and parts.

키워드

과제정보

이 연구는 (주)현대두산인프라코어의 지원을 받아 수행되었으며, 또한 건설기계 R&D 전문인력양성사업의 지원을 받아 연구가 수행되었음을 밝힙니다.

참고문헌

  1. H. M. Moon et al., "Active Vibration Control of Three-Stage Mast of Reach Truck," Journal of Drive and Control, Vol.16, No.3, pp.1-7, 2019. https://doi.org/10.7839/KSFC.2019.16.3.001
  2. D. Y. Shin, "A Study on Excavation Path Design of Excavator Considering Motion Limits," Journal of Drive and Control, Vol.18, No.2, pp.20-31, 2021. https://doi.org/10.7839/KSFC.2021.18.2.020
  3. C. H. Jeong and J. S. Lee, "Thermal-Fluid Analysis with Flow Loss Coefficient on the Inlet and Exhaust Duct of Wheel-Loader," Transactions of the KSME C Industrial Technology and Innovation, Vol.5, No.2, pp.97-104, 2017. https://doi.org/10.3795/KSME-C.2017.5.2.097
  4. J. S. Lee et al., "Verification of Engine Room Thermal Flow Analysis for Design Evaluation of Excavator Cooling System," Journal of Computational Fluids Engineering, Vol.24, No.2, pp.1-7, 2019. https://doi.org/10.6112/kscfe.2019.24.2.001
  5. J. S. Lee et al., "Verification of Engine Room Thermal Flow Analysis for Design Evaluation of Excavator Cooling System," Journal of Mechanical Science and Technology, Vol.3, No.7, pp.3265-3275, 2019.
  6. F. G. Rising, "Engine Cooling System Design for Heavy Duty Trucks," SAE770023, 1977.
  7. N. Katoh, T. Ogawa and T. Kuriyama, "Numerical simulation on the three dimensional flow and heat transfer in the engine compartment," SAE910306, 1991.
  8. H. Shimonosono, Y. Shibata and K. Fujitani, "Optimization of the Heat Flow Distribution in the Engine Compartment," SAE930883, 1993.
  9. C. Eric, D. Bruno, M. Stephane, B. Robert and B. Farid, "CFD Based Design for Automotive Engine Cooling Fan System," SAE980427, 1998.
  10. B. Uhl, F. Brotz, J. Fauser and U. Kruger, "Development of Engine Cooling System by Coupling CFD Simulation and Heat Exchanger Analysis Programs," SAE2001-01-1695, 2001.
  11. K. T. Oh et al., "Automobile Underhood Thermal and Air Flow Simulation using CFD," Journal of Computational Fluids Engineering, Vol.12, No.1, pp.22-27, 2007.
  12. S. W. Noh et al., "A Study on the Optimization of Heat Flux in Engine Room of Auxiliary Power Unit for Self-Propelled Artillery," Journal of the Korea Academia-Industrial Cooperation Society, Vol.20, No.12, pp.629-635, 2019.
  13. T. E. Lee et al., "A Study on Thermal and Fluid Characteristics inside Engine Room of Auxiliary Power Unit for Tracked Vehicle," Journal of the Korean Society for Precision Engineering, Vol.26, No.12, pp.85-93, 2009.
  14. Fluent 6.2 User Guide, Fluent Inc.