Nuclear Engineering and Technology

Korean Nuclear Society (한국원자력학회)
권호 표지
DOI QR코드

DOI QR Code

CFD analysis of the flow blockage in a rectangular fuel assembly of the IAEA 10 MW MTR research reactor

  • Xia, Shuang (College of Nuclear Science and Technology, Harbin Engineering University) ;
  • Zhou, Xuhua (Naval Research Academy of China) ;
  • Hu, Gaojie (Naval Research Academy of China) ;
  • Cao, Xiaxin (College of Nuclear Science and Technology, Harbin Engineering University)
  • Received : 2020.05.08
  • Accepted : 2021.03.28
  • Published : 2021.09.25
Download PDF
⟨ Previous Next ⟩

Abstract

When a nuclear reactor with rectangular fuel assemblies runs for a long time, impurities and debris may be taken into coolant channels, which may cause flow blockage, and the blocked fuel assemblies might be destroyed. Therefore, the purpose of this study is to perform a thermal-hydraulic analysis of a rectangular fuel assembly by STAR-CCM+, under the condition of one subchannel with 80% blockage ratio. A rectangular fuel assembly of the International Atomic Energy Agency (IAEA) 10 MW material test reactor (MTR) is chosen. In view of the gasket material taken into the coolant channel is close to the single side of the coolant channel, in the flow blockage accident of the Oak Ridge Research Reactor (ORRR), a new blockage category called single side blockage is attempted. The blockage positions include inlet, middle and outlet, and the blockage is set as a cuboid. It is found by simulations that the blockage redistributes the mass flow rate, and large vortices appear locally. The peak temperature of the cladding is maximum, when the blockage is located at the single side of the coolant channel inlet, and no boiling occurs in all blockage cases. Moreover, as the height of the blockage increases, the damage caused by the blockage increases slightly.

Keywords

References

  1. F.R. Keller, Fuel Element Flow Blockage in the Engineering Test reactor[C], AEC Research and Development Report, seventeenth ed., TID-4500, Reactor Technology, 1962.
  2. T.M. Sims, W.H. Tabor, Report on Fuel Plate Melting at the Oak Ridge Research Reactor: ORNL-TM-627 [R], ORNL, USA, Oak Ridge, 1964.
  3. J. Li, X. Chen, J. Li, Analysis on a flow blockage incident at a plate-type fuel reactor, Atomic Energy Sci. Technol. 36 (1) (2002) 76-79. https://doi.org/10.3969/j.issn.1000-6931.2002.01.018
  4. M. Adorni, A. Bousbia-Salah, T. Hamidouche, et al., Analysis of partial and total flow blockage of a single fuel assembly of an MTR research reactor core, Ann. Nucl. Energy 32 (2005) 1679-1692. https://doi.org/10.1016/j.anucene.2005.06.001
  5. Q. Lu, S. Qiu, G.H. Su, Flow blockage analysis of a channel in a typical material test reactor core, Nucl. Eng. Des. 239 (2009) 45-50. https://doi.org/10.1016/j.nucengdes.2008.06.016
  6. X. Li, S. Peng, S. Bi, Study on effect of flow blockage at inlet of plate-type fuel element on thermal-hydraulic characteristics of reactor core, Nucl. Power Eng. 35 (5) (2014) 138-142.
  7. T. Liu, H. Jin, L. Yuan, Flow blockage accident analysis for China advanced research reactor, Nucl. Power Eng. 27 (5) (2006) 32-44.
  8. H.M. Son, S.H. Yang, C. Park, et al., Transient thermal-hydraulic analysis of complete single channel blockage accident of generic 10 MW research reactor, Ann. Nucl. Energy 75 (2015) 44-53. https://doi.org/10.1016/j.anucene.2014.08.002
  9. L. Song, Numerical Analysis of the Flow Blockage Accidents in Plate-type Fuel Assembly, A Dissertation for the Degree of M. Eng., Harbin Engineering University, 2013.
  10. A. Salama, CFD analysis of fast loss of flow accident in typical MTR reactor undergoing partial and full blockage: the average channel scenario, Prog. Nucl. Energy 60 (2012) 1-13. https://doi.org/10.1016/j.pnucene.2012.05.002
  11. A. Salama, E.D. El-Morshedy, CFD analysis of flow blockage in MTR coolant channel under loss-of-flow transient: hot channel scenario, Prog. Nucl. Energy 55 (2012) 78-92. https://doi.org/10.1016/j.pnucene.2011.11.005
  12. A. Salama, E.D. El-Morshedy, CFD simulation of flow blockage through a coolant channel of a typical material testing reactor core, Ann. Nucl. Energy 41 (2012) 26-39. https://doi.org/10.1016/j.anucene.2011.09.005
  13. A. Salama, M.F. El-Amin, S. Sun, Three-dimensional, numerical investigation of flow and heat transfer in rectangular channels subject to partial blockage, Heat Tran. Eng. 36 (2015) 152-165. https://doi.org/10.1080/01457632.2014.909191
  14. A. Davari, S.M. Mirvakili, E. Abedi, Three-dimensional analysis of flow blockage accident in Tehran MTR research reactor core using CFD, Prog. Nucl. Energy 85 (2015) 605-612. https://doi.org/10.1016/j.pnucene.2015.08.008
  15. Z. Ma, R. Chen, M. Tian, et al., Analysis of flow blockage accidents in rectangular fuel assembly based on CFD methodology, Ann. Nucl. Energy 112 (2018) 71-83. https://doi.org/10.1016/j.anucene.2017.09.012
  16. Y. Guo, G. Wang, D. Qian, et al., Accident safety analysis of flow blockage in an assembly in the JRR-3M research reactor using system code RELAP5 and CFD code FLUENT, Ann. Nucl. Energy 122 (2018) 125-136. https://doi.org/10.1016/j.anucene.2018.08.031
  17. L. Li, D. Fang, D. Zhang, et al., Flow and heat transfer characteristics in platetype fuel channels after formation of blisters on fuel elements, Ann. Nucl. Energy 134 (2019) 284-298. https://doi.org/10.1016/j.anucene.2019.06.030
  18. W. Fan, C. Peng, Y. Guo, CFD study on inlet flow blockage accidents in rectangular fuel assembly, Nucl. Eng. Des. 292 (2015) 177-186. https://doi.org/10.1016/j.nucengdes.2015.06.016
  19. W. Fan, C. Peng, Y. Chen, et al., A new CFD modeling method for flow blockage accident investigations, Nucl. Eng. Des. 303 (2016) 31-41. https://doi.org/10.1016/j.nucengdes.2016.04.006
  20. IAEA, Research reactor core conversion guidebook, volume 3: analytical verification (Appendices G and H), in: IAEA-TECDOC-643, IAEA, 1992.
  21. T.-H. Shih, W.W. Liou, A new k-ε eddy viscosity model for high Reynolds number turbulent flows-model development and validation, NASA TM (1994) 106721.
  22. STAR-CCM+ Version 13.04, User Guide, Siemens Inc., 2018.
  23. P.R. Spalart, C.L. Rumsey, Effective inflow conditions for turbulence models in aerodynamic calculations, AIAA J. 45 (10) (2007) 2544-2553. https://doi.org/10.2514/1.29373
  24. STAR-CCM+ Version 13.04, Tutorial Files, Siemens Inc., 2018.
  25. J.P. Holman, Heat Transfer, tenth ed., McGraw-Hill, 2010.
  26. J. Ma, L. Li, Y. Huang, et al., Experimental studies on single-phase flow and heat transfer in a narrow rectangular channel, Nucl. Eng. Des. 241 (2011) 2865-2873. https://doi.org/10.1016/j.nucengdes.2011.04.047
  27. C. Wang, P. Gao, S. Tan, et al., Experimental study of friction and heat transfer characteristics in narrow rectangular channel, Nucl. Eng. Des. 250 (2012) 646-655. https://doi.org/10.1016/j.nucengdes.2012.06.029
  28. J.C. Vogel, J.K. Eaton, Combined heat transfer and fluid dynamic measurements downstream of a backward-facing step, AIAA J. 23 (2) (1985) 163-171. https://doi.org/10.2514/3.8890