DOI QR코드

DOI QR Code

Static wind loads on rigid roof model with complex hyperbolic geometry

  • Delnero, Juan S. (Laboratorio de Capa Límite y Fluidodinamica Ambiental (UIDET LaCLyFA), Facultad de Ingenieria) ;
  • Di Leo, Julio Maranon (Laboratorio de Capa Límite y Fluidodinamica Ambiental (UIDET LaCLyFA), Facultad de Ingenieria) ;
  • Martinez, Mariano A. (Grupo de Fluidodinamica Computacional, Universidad Nacional de La Plata)
  • 투고 : 2020.09.24
  • 심사 : 2021.08.27
  • 발행 : 2021.09.25

초록

The use of tensioned structures, such as membranes, as solutions for roofing and other kinds of covers has become more and more frequent. Current regulations do not provide detailed information about the coefficients needed to develop efficient designs, regarding wind loads. A lot of simulations and tests have been performed on different geometries which are typically used in these kinds of designs. However, no precise and clear standard has been established, yet, in order to regulate efficiently this application. Current regulations consider only simple geometries, while the effects of the interference between multiple covers or between a cover and the near urban environment is completely absent. In this paper are presented the results obtained from testing a 1:75 scale complex geometry model in a boundary layer wind tunnel. More precisely a model of a parking lot for vans, roofed with a complex geometry tensioned membrane was tested in order to measure its pressure distribution. Due to the high complexity of the geometry and in order to obtain a better description of the effects of the wind it was decided to lead wind tunnel tests to validate and to verify the load conditions over the roof. Information about wind load distributions for simple geometries such as cones, hyperboloids, etc. alone can be easily found in current technical bibliography. However, when designs are based on more complex shapes, including arrays of simpler shapes, a profound lack of information is observed. Therefore, it is not possible to calculate the wind loads over the membrane which are needed to dimension the supporting structure.

키워드

과제정보

Special thanks to the company WAGG SA, without which this investigation would not have been possible. To CONICET and all the members and facilities of the UIDET LaCLyFA of the Aeronautical Department of the Faculty of Engineering of the National University of La Plata.

참고문헌

  1. ASCE (American Society of Civil Engineering) (1999), Wind Tunnel Studies of Buildings and Structures. Manuals of Practice (MOP).
  2. Baglin, P. (2002), ARIES Canopy Wind Tunnel Results.
  3. Baskaran, A., Murty, B. and Tanaka, H. (2011), "Generalized load cycles for dynamic wind uplift evaluation of rigid membrane roofing systems", Wind and Structures, 14(5), 383-411. https://doi.org/10.12989/was.2011.14.5.383
  4. Burton, J. and Gosling, P. (2003), "Wind tunnel pressure measurements on conic shaped membrane roof arrangements", Proceeding of International Conference on Textile Composite and Inflatable Structures - Structural Membranes, CIMNE, Barcelona, Spain. 427-432.
  5. Carradine, D.M. (1998), Experiments on The Response of ArchSupported Membrane Shelters to Snow and Wind Loading, Master Thesis, Virginia Polytechnic Institute and State University, Blacksburg, U.S.A.
  6. CEN/TC 152 (2015), EN 13782:2015 - Temporary Structure - Tents - Safety.
  7. CEN/TC 250 (2005), EN 1991-1-4: Eurocode 1: Actions on Structures - Part 1-4: General Actions - Wind Actions.
  8. Chang, C.C. and Ji, Y.F. (2007), "Flexible videogrammetric technique for three-dimensional structural vibration measurement", J. Eng. Mech., 133(6), 656-664. https://doi.org/10.1061/(ASCE)0733-9399(2007)133:6(656).
  9. CIRSOC 102-2005 (2005), "Reglamento Argentino de la Accion del Viento Sobre las Construcciones", INTI Argentina.
  10. Cook, N.J. and Mayne, J.R. (1979), "A novel working approach to the assessment of wind loads for equivalent static design", J. Wind Eng. Ind. Aerod., 4, 149-164. https://doi.org/10.1016/0167-6105(79)90043-6.
  11. Davenport A.G. (1965), "The relationship of wind structure to wind loading", Proceeding 1st Conference on Wind Effects on Building and Structures, National Physical Laboratory, Teddington, United Kingdom, 53-102.
  12. Davenport, A.G. (1960), "Rationale for determining design wind velocities", ASCE J. Struct. Div., 86(5), 39-68. https://doi.org/10.1061/JSDEAG.0000521.
  13. Elnokaly, A., Chilton, J. and Wilson, R. (2004), "CFD investigation of airflow around conic tensile membrane structures", Proceeding of the International Sympsoium on Shell and Spatial Structures from Model to Realization, IASS, Montpellier, France, 138-139.
  14. Forster, B. and Mollaert, M. (2004), "European Design Guide for Tensile Surface Structures", Tensinet VUB, Brussels.
  15. Gorlin, W.B. (2009a), "Wind loads for temporary structures: Making the case for industrywide standards", J. Architect. Eng., 15(2), 35-36. https://doi.org/10.1061/(ASCE)1076-0431(2009)15:2(35).
  16. Gorlin, W.B. (2009b), Temporary Structures Need Wind-Load Standards, Structure magazine.
  17. Holmes, J.D. (2007), Wind Loading of Structures, Taylor & Francis, London, England.
  18. Irwin, P., Gamble, S.L. and Taylor D.A. (2011), "Effect of roof size, heat transfer, and climate on snow loads: Studies for the 1995 NBC", Canadian Journal of Civil Engineering, 22(4), 770-784. https://doi.org/10.1139/l95-087
  19. Liu, C.J., Zheng, Z.L., Long, J., Guo, J.J. and Wu, K. (2013), "Dynamic analysis for nonlinear vibration of prestressed orthotropic membranes with viscous damping", Int. J. Struct. Stabil. Dyn., 13(2), 60-66. https://doi.org/10.1142/S0219455413500181
  20. Liu, M., Chen, X. and Yang, Q. (2016), "Characteristics of dynamic pressures on a saddle type roof in various boundary layer flows", J. Wind Eng. Ind. Aerod., 150(4), 1-14. https://doi.org/10.1016/j.jweia.2015.11.012.
  21. Luo, J. and Han, D. (2009), "3D wind-induced response analysis of a cable-membrane structure", J. Zhejiang University - Sci. A: Appl. Phys. Eng., 10(3), 337-344. https://doi.org/10.1631/jzus.A0820430
  22. Michalski, A., Kermel, P., Haug, E., Lohner, R., Wuchner, R. and Bletzinger, K.U. (2004), "Validation of the computational fluid-structure interaction simulation at real-scale tests of a flexible 29 m umbrella", J. Wind Eng. Ind. Aerod., 99(4), 400-413. https://doi.org/10.1016/j.jweia.2010.12.010.
  23. Nagai, Y., Okada, A., Miyasato, N. and Saitoh, M. (2010), "Basic study on multi-bay horn-shaped membrane roof: Evaluation of wind load and influence of supporting system on structural behavior under winds", Int. J. Space Struct., 25(1), 35-43. https://doi.org/10.1260/0266-3511.25.1.35
  24. Nagai, Y., Okada, A., Miyasato, N. and Saitoh, M. (2011), Wind Tunnels and Experimental Fluid Dynamics Research, Chapter: Wind Tunnel Tests on the Horn-Shaped Membrane Roof, 325-348, InTech, London, United Kingdom.
  25. Nagai, Y., Okada, A., Miyasato, N. and Saitoh, M. (2012), "Wind response of horn-shaped membrane roof and proposal of gust factor for membrane structures", J. Int. Assoc. Shell Spatial Struct., 53(3), 169-176.
  26. Peterka, J.A. (1983), "Selection of local peak pressure coefficients for wind tunnel studies of buildings", J. Wind Eng. Ind. Aerod., 13(1-3), 447-188. https://doi.org/10.1016/0167-6105(83)90166-6
  27. Qingshan, Y., Yue, W. and Weiliang, Z. (2010), "Experimental study on interaction between membrane structure and wind environment", Earthq. Eng. Eng. Vib., 9(4), 523-532. https://doi.org/10.1007/s11803-010-0034-0.
  28. Rank, E., Halfmann, A., Scholz, D., Gluck, M., Breuer, M. and Durst, F. (2005), "Wind loads on lightweight structures: Numerical simulation and wind tunnel tests", Gesellschaft fur Angewandte Mathematik und Mechanik (GAMM), 28(1), 73-89. https://doi.org/10.1002/gamm.201490014.
  29. Rizzo, F. and Ricciardelli, F. (2016), "Design approach of wind load for Hyperbolic paraboloid roof with circular and elliptical plan", Eng. Struct., 139, 153-169. https://doi.org/10.1016/j.engstruct.2017.02.035
  30. Rizzo, F. and Sepe, V. (2015), "Static loads to simulate dynamic effects of wind on hyperbolic paraboloid roofs with square plan", J. Wind Eng. Ind. Aerod., 137, 46-57. https://doi.org/10.1016/j.jweia.2014.11.012.
  31. Rizzo, F., D'Asdia, P., Lazzari, M. and Procino, L. (2011), "Wind action evaluation on tension roofs of hyperbolic paraboloid shape", Eng. Struct., 33(2), 445-461. https://doi.org/10.1016/j.engstruct.2010.11.001.
  32. Rizzo, F., D'Asdia, P., Ricciardelli, F. and Bartoli, G. (2012), "Characterization of pressure coefficients on hyperbolic paraboloid roofs", J. Wind Eng. Ind. Aerod., 102, 61-71. https://doi.org/10.1016/j.jweia.2012.01.003.
  33. Simiu, E. and Scanlan, H. (1996), Wind Effects On Structures, John Wiley & Sons, New York.
  34. Sun, X., Wu, Y., Yang, Q. and Shen, S. (2008), "Wind tunnel tests on the aeroelastic behaviors on pretensioned sadle-shaped suspended roofs", Proceeding of the 6th International Colloquium on Bluff Body Aerodynamics and Applications, BBAA, Milano, Italy, 1-10.
  35. Takeda, F., Yoshino, T. and Uematsu, Y. (2014), "Design wind force coefficients for hyperbolic paraboloid free roofs", J. Phys. Sci. Appl., 4(1), 1-19.
  36. Xu, Y., Zheng, Z., Liu, C., Wu, K. and Song, W. (2018), "Aerodynamic stability analysis of geometrically nonlinear orthotropic membrane structure with hyperbolic paraboloid in sag direction", Wind Struct., 26(6), 355-367. http://dx.doi.org/10.12989/was.2018.26.6.355.
  37. Xuanyi, Z., Zhihui, H., Ming, G., An-an Z., Weiyu, Z. and Wei, F. (2013), "Research on wind-induced responses of a largescale membrane structure", Earthq. Eng. Eng. Vib., 12 (2), 297-305. https://doi.org/10.1007/s11803-013-0172-2.
  38. Yang, Q., Wu, Y. and Zhu, W. (2010), "Experimental study on interaction between membrane structures and wind environment", Earthq. Eng. Eng. Vib., 9(4), 523-532. https://doi.org/10.1007/s11803-010-0034-0.