DOI QR코드

DOI QR Code

Aerodynamic modifications for reduction of wind loads on cross plan shaped tall building

  • Kumar, Debasish (Department of Civil Engineering, Indian Institute of Engineering Science and Technology) ;
  • Dalui, Sujit Kumar (Department of Civil Engineering, Indian Institute of Engineering Science and Technology)
  • Received : 2020.11.25
  • Accepted : 2021.08.03
  • Published : 2021.08.25

Abstract

Corner modification plays an essential role in the reduction of the wind load and responses on tall buildings. The present study investigates the effectiveness of different corner modifications (chamfered, rounded, and recessed corners) to reduce the wind load on regular cross plan shaped tall buildings using the computation fluid dynamics technique. Here, ANSYS CFX is used to simulate the boundary layer wind environment around the building and compared with experimental results. The numerically simulated data are compared with some previous wind tunnel test data on the '+' plan building. Based on the numerical study, flow pattern near the corner regions, pressure contour, the variation of pressure coefficient along the periphery of the building, force and moment coefficients for three corner modified models are analyzed and compared with sharp edged cross plan shaped model to comprehend the extent of nonconformities due to corner modifications. The rounded corner modification is most effective in suppressing the wind load compared to chamfered and recessed corners. For rounded corners with 50% corner cut, the reduction in force and moment coefficients is substantial, with up to 26.26% and 28.58%, respectively, compared to sharp edged corners. A sudden shoot up in the negative Cp values near edges of the corner modified model, should require special attention in the design of cladding components. This paper led to comprehend the wind-induced responses of cross plan shaped building with various corner configurations.

Keywords

References

  1. AIJ (2004), Recommendation for Loads on Buildings, Architectural Institute of Japan, Tokyo, Japan.
  2. Amano, T. (1995). "The Effect of corner-cutting of three dimensional square cylinders on vortex-induced oscillation and galloping in uniform flow", J. Struct. Construct. Eng., 478, 63-69. https://doi.org/10.3130/aijs.60.63.
  3. Amin, J.A. and Ahuja, A.K. (2010), "Aerodynamic modifications to the shape of the buildings: A review of the state-of-the-art", Asian J. Civil Eng., 11(4), 433-450.
  4. ASCE (2013), Minimum Design Loads for Buildings and Other Structures. American Society of Civil Engineers.
  5. AS/NZS (2002), Structure Design Actions, Part - 2: Wind Actions, Australian/ New Zealand Standard, Sydney, and Wellington.
  6. Bairagi, A.K. and Dalui, S.K. (2015), "Comparison of aerodynamic coefficients of set-back tall buildings due to wind load", Asian J. Civil Eng., 19(2), 205-221. https://doi.org/10.1007/s42107-018-0018-3.
  7. Bandi, E.K., Tamura, Y., Yoshida, A., Kim, Y.C. and Yang, Q. (2013), "Experimental investigation on aerodynamic characteristic of various triangular-section high-rise buildings", J. Wind Eng. Ind. Aerod., 122(2013), 60-68. https://doi.org/10.1016/j.jweia.2013.07.002
  8. Bhattacharyya, B. and Dalui, S.K. (2020), "Experimental and numerical study of wind-pressure distribution on irregular-plan-shaped building", J. Struct. Eng., 146(7), 04020137. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002686.
  9. Carassale, L., Freda, A. and Marre-Brunenghi, M. (2014), "Experimental investigation on the aerodynamic behavior of square cylinders with rounded corners", J. Fluids Struct., 44(7), 195-204. https://doi.org/10.1016/j.jfluidstructs.2013.10.010.
  10. Celik, I.B., Ghia, U., Roache, P.J. and Freitas, C.J. (2008), "Procedure for estimation and reporting of uncertainty due to discretization in CFD applications", J. Fluids Eng. Transactions ASME, 130(7).
  11. Chakraborty, S., Dalui, S.K., and Ahuja, A.K. (2014), "Wind load on irregular plan shaped tall building - A case study", Wind Struct., 19(1), 59-73. https://doi.org/10.12989/was.2014.19.1.059.
  12. Chakraborty, S., Dalui, S.K. and Ahuja, A.K., (2014b), "Experimental and numerical study of surface pressure on'+' plan shape tall building", Jordon J. Civil Eng., 8(3), 251-262.
  13. Choi, C.K. and Kwon, D.K. (1999), "Aerodynamic stability for square cylinder with various corner cuts", Wind Struct., 2(3), 173-187. https://doi.org/10.12989/was.1999.2.3.173.
  14. Cooper, K.R., Nakayama, M., Sasaki, Y., Fediw, A.A., ResendeIde, S. and Zan, S.J. (1997), "Unsteady aerodynamic force measurements on a super-tall building with a tapered cross section,", J. Wind Eng. Ind. Aerod., 72, 199212. https://doi.org/10.1016/S0167-6105(97)00258-4.
  15. Dalui, S.K. (2008), Wind Effects on Tall Buildings with Peculiar Shapes, Ph.D. Dissertation, Indian Institute of Technology, Roorkee, India.
  16. Dalui, S.K., Kar, R. and Hajra, S. (2015), "Interference effects on octagonal plan shaped tall building under wind - A case study", In the proceeding of Scientific Co-operations Workshops On Engineering Branches, Istanbul - Turkey, September.
  17. Derakhshandeh, J.F and Alam, M.M. (2018), "Flow structures around rectangular cylinder in the vicinity of a wall", Wind Struct., 26(5), 293-304. http://dx.doi.org/10.12989/was.2018.26.5.293.
  18. Dutton, R. and Isyumov, N. (1990), "Reduction of tall building motion by aerodynamic treatments", J. Wind Eng. Ind. Aerod., 36(1990), 739-747. https://doi.org/10.1016/0167-6105(90)90071-J.
  19. Endo, M., Beinkiewicz, B. and Ham, H.J. (2006), "Wind-tunnel investigation of point pressure on TTU test building", J. Wind Eng. Ind. Aerod., 94(7), 553-578. https://doi.org/10.1016/j.jweia.2006.01.019.
  20. Elshaer, A., Bitsuamlak, G.T. and El Damatty, A. (2014), "Vibration control of tall buildings using aerodynamic optimization", In: 25th CANCAM London, Ontario, Canada.
  21. Elshaer, A., Bitsuamlak, G.T. and El Damatty, A. (2016), "Aerodynamic shape optimization of tall buildings using twisting and corner modifications", In 8th International Colloquium on Bluff Body Aerodynamics and Applications Northeastern University, Boston, U.S.A., June.
  22. Elshaer, A., Bitsuamlak, G.T. and El Damatty A. (2017), "Enhancing wind performance of tall buildings using corner aerodynamic optimization", Eng. Struct., 136, 133-148. https://doi.org/10.1016/j.engstruct.2017.01.019.
  23. Franke, J., Hirsch, C., Jensen, A.G., Krus, H.W., Schatzmann, M., Westbury, P.S. and Wright, N.G. (2004), "Recommendations on the use of CFD in predicting pedestrian wind environment", In Cost action C.
  24. Gomes, M.G., Rodrigues, A.M. and Mendes, P. (2005), "Experimental and numerical study of wind pressures on irregular-plan shapes", J. Wind Eng. Ind. Aerod., 93, 741-756. https://doi.org/10.1016/j.jweia.2005.08.008.
  25. Hayashida, H. and Iwasa, Y. (1990), "Aerodynamic shape effects of tall building for vortex induced vibration", J. Wind Eng. Ind. Aerod., 33(1-2), 237-242. https://doi.org/10.1016/0167-6105(90)90039-F
  26. Hayashida, H., Mataki, Y. and Iwasa, Y. (1992), "Aerodynamic damping effects of tall building for a vortex induced vibration", J. Wind Eng. Ind. Aerod., 43(1-3), 1973-1983. https://doi.org/10.1016/0167-6105(92)90621-G
  27. IS 875(Part -3) (2015), Indian standard code of practice for design loads (other than earthquake) for buildings and structures. Part-3 (Wind loads). Bureau of Indian Standards, New Delhi.
  28. Kar, R., Dalui, S.K. and Bhattacharya, S. (2019), "An efficient optimization approach for wind interference effect on octagonal tall building", Wind Struct., 28(2), 111-128. https://doi.org/10.12989/was.2019.28.2.111.
  29. Karim, A. (1988), "Mitigation of wind induced motion of tall building", J. Wind Eng. Ind. Aerod., 11(1983), 273-284. https://doi.org/10.1016/0167-6105(83)90106-X.
  30. Kawai, H. (1998), "Effects of corner modifications on aeroelastic instabilities of tall buildings", J. Wind Eng. Ind. Aerod., 74, 719-729. https://doi.org/10.1016/S0167-6105(98)00065-8.
  31. Kim, Y.C. and Kanda, J. (2010), "Effects of taper and set-back on wind force and wind-induced response of tall buildings", Wind Struct., 13(6), 499-517. https://doi.org/10.12989/was.2010.13.6.499.
  32. Kim, Y.M. and You, K.P. (2002), "Dynamic responses of a tapered tall building to wind load", J. Wind Eng. Ind. Aerod., 90(12-15), 1771-1782. https://doi.org/10.1016/S0167-6105(02)00286-6.
  33. Kim, Y.M., You, K.P. and Ko, N.H. (2008), "Across-wind response of an aeroelastic tapered tall building", J. Wind Eng. Ind. Aerod., 96(8-9), 1307-1319. https://doi.org/10.1016/j.jweia.2008.02.038.
  34. Kumar, D. and Dalui, S.K. (2017), "Effect of internal angles between limbs of cross plan shaped tall building under wind load", Wind Struct., 24(2), 95-118. https://doi.org/10.12989/was.2017.24.2.095.
  35. Kwok, K.C.S. (1988), "Effects of building shape on wind-induced response of tall buildings", J. Wind Eng. Ind. Aerod., 28(1988), 381-90. https://doi.org/10.1016/0167-6105(88)90134-1.
  36. Kwok, K.C. and Bailey, P.A. (1987), "Aerodynamic devices for tall buildings and structures", J. Eng. Mech., 113(3), 349-365. https://doi.org/10.1061/(ASCE)0733-9399(1987)113:3(349)
  37. Kwok, K.C.S., Wilhelm, P.A. and Wilkie, B.G. (1988), "Effect of edge configuration on wind induced response of tall buildings", Eng. Struct., 10(1988), https://doi.org/10.1016/0141-0296(88)90039-9.
  38. Li, Y. and Li, Q. (2016), "Across-wind dynamics load on L-shaped tall buildings", Wind Struct., 23(5), 385-403. https://doi.org/10.12989/was.2016.23.5.385.
  39. Li, B., Liu, J. and Li, M. (2013), "Wind tunnel study on the morphological parameterization of building non-uniformity", J. Wind Eng. Ind. Aerod., 121(2013), 60-69. https://doi.org/10.1016/j.jweia.2013.07.017.
  40. Li, Y., Tian, X., Tee, K.F., Li, Q.S. and Li, Y.G. (2018), "Aerodynamic treatments for the reduction of wind loads on high-rise buildings", J. Wind Eng. Ind. Aerod., 172, 107-115. https://doi.org/10.1016/j.jweia.2017.11.006.
  41. Mallick, M., Mohanta, A., Kumar, A. and Patra, K. (2020), "Gene-expression programming for the assessment of surface mean pressure coefficient on building surface", Buil. Simu., https://doi.org/10.1007/s12273-019-0583-8.
  42. Melbourne, N.H. and Cheung, J.C.K. (1988), "Designing for serviceable accelerations in tall buildings", In the 4th International Conference on Tall Buildings, Hong Kong and Hanghai, 148-155.
  43. Meng, F., He, B., Zhu, J., Zhao Amos, D., Darko, A. and Zhao, Z. (2018), "Sensitivity analysis of wind pressure coefficients on CAARC standard tall buildings in CFD simulations", J. Buil. Eng., 16, 146-158. https://doi.org/10.1016/j.jobe.2018.01.004.
  44. Miyashita, K., Katagiri, J. and Nakamura, O. (1993), "Wind-induced response of high-rise buildings effects of corner cuts or openings in square buildings", J. Wind Eng. Ind. Aerod., 50, 319-328. https://doi.org/10.1016/0167-6105(93)90087-5.
  45. Miyashita, K., Katagiri, J., Nakamura, O., Ohkuma, T., Tamura, Y., Itoh, M. and Mimachi, T. (1993), "Wind-induced response of high-rise buildings effects of corner cuts or openings in square buildings", J. Wind Eng. Ind. Aerod., 50, 319-328. https://doi.org/10.1016/0167-6105(93)90087-5.
  46. Montazeri, H. and Blocken, B. (2013), "CFD simulation of windinduced pressure coefficients on buildings with and without balconies: validation and sensitivity analysis", Buil. Environ., 60, 137-149. https://doi.org/10.1016/j.buildenv.2012.11.012.
  47. Mukherjee, S., Chakraborty, S., Dalui, S.K. and Ahuja, A.K. (2014), "Wind Induced pressure on 'Y' plan shape tall building", Wind Struct., 19(5), 523-540. https://doi.org/10.12989/was.2014.19.5.523.
  48. Okada, H. and Kong, L. (1999), The Effects of Open Passage on Reducing Wind Response of Tall Building, 29th Technical Report, Public Works Research Institute.
  49. Pal, R. and Dalui, S.K. (2016), "Wind effects on 'Z' plan shaped tall building: a case study", Int. J. Adv. Struct. Eng., https://doi.org/10.1007/s40091-016-0134-9.
  50. Revuz, J., Hargreaves, D.M. and Owen, J.S. (2012), "On the domain size of steady-state CFD modeling of a tall building", Wind Struct., 15(4), 313-329. https://doi.org/10.12989/was.2012.15.4.313.
  51. Sanyal, P. and Dalui, S.K. (2020), "Effect of corner modifications on 'Y' plan shaped tall building under wind load", Wind Struct., 30(3), 245-260. http://dx.doi.org/10.12989/was.2020.30.3.245.
  52. Sanyal, P. and Dalui, S.K. (2021), "Effect of internal angle between limbs of 'Y' plan shaped tall building under wind load", J. Buil. Eng., 33(2021), 101843. https://doi.org/10.1016/j.jobe.2020.101843.
  53. Sun, X., Liu, H., Su, N. and Wu, Y. (2017), "Investigation on wind tunnel tests of the kilometer skyscraper", Eng. Struct., 148, 340-356. http://doi.org/10.1016/j.engstruct.2017.06.052.
  54. Tanaka, H., Tamura, Y., Ohtake, K., Nakai, M. and Kim, Y.C. (2012), "Experimental investigation of aerodynamic forces and wind pressures acting on tall buildings with various unconventional configurations", J. Wind Eng. Ind. Aerod., 107, 179-191. https://doi.org/10.1016/j.jweia.2012.04.014
  55. Taranath, B.S. (2016), Tall Building Design: Steel, Concrete and Composite System, CRC Press, U.S.A.
  56. Thordal, M.S., Bennetsen, J.C. and Koss, H.H.H. (2019), "Review of the practical application of CFD for the determination of wind load on high-rise buildings", J. Wind Eng. Ind. Aerod., 186, 155-168. https://doi.org/10.1016/j.jweia.2018.12.019.
  57. Xie, J.M. (2014), "Aerodynamic optimization of super-tall buildings and its effectiveness assessment", J. Wind Eng. Ind. Aerod., 130, 88-98. https://doi.org/10.1016/j.jweia.2014.04.004.
  58. Yi, J. and Li, Q.S. (2015), "Wind tunnel and full-scale study of wind effects on a super-tall building", J. Fluids Struct., 58, 236253. https://doi.org/10.1016/j.jfluidstructs.2015.08.005.
  59. You, K.P., Kim, Y.M. and Ko, N.H. (2008), "The evaluation of wind-induced vibration responses to a tapered tall building", Struct. Des. Tall Spec. Build., 17(3), 655-667. https://doi.org/10.1002/tal.371
  60. Zhengwei, Z., Yonga, Q., Minga, G., Nankuna, T. and Yongc, X. (2012), "Effects of corner recession modification on aerodynamic coefficients of square tall buildings", In the Seventh International Colloquium on Bluff Body Aerodynamics and Applications, China, September.