DOI QR코드

DOI QR Code

Development of wireless SHM sensor node for in-flight real-time monitoring using embedded CNT fiber sensors

  • Park, Jinwoo (Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology) ;
  • Sung, Yeol-Hun (Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology) ;
  • On, Seung Yoon (Department of Mechanical Engineering, Korea Advanced Institute of Science and Technology) ;
  • Kwon, O-Hyun (School of Aerospace and Mechanical Engineering, Korea Aerospace University) ;
  • Bang, Hyochoong (Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology) ;
  • Kim, Seong Su (Department of Mechanical Engineering, Korea Advanced Institute of Science and Technology) ;
  • Han, Jae-Hung (Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology) ;
  • Lee, Jung-Ryul (Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology)
  • Received : 2020.07.02
  • Accepted : 2021.03.22
  • Published : 2021.09.25

Abstract

Structural health monitoring (SHM) is essential for composite unmanned aerial vehicles (UAVs). Additionally, because UAVs are extremely sensitive to weight and volume, the minimal addition of weight and volume by the SHM system is crucial. Therefore, we proposed a compact and lightweight wireless SHM sensor node and an embedded carbon nanotube (CNT) fiber sensor for in-flight SHM of UAVs. The wireless SHM sensor node was composed of an analog sensing circuit, wireless microcontroller unit, and analog low pass filter. The small diameter CNT fiber sensor was developed to be easily embedded inside composite structures and to enhance their structural properties while performing as an SHM sensor. Glass composite skin with embedded CNT fiber sensors composed of ultra-high-molecular-weight polyethylene, polyurethane, CNT, and carbon black were installed in the aircraft. For comparison, a strain gauge attached at the center of a long CNT fiber sensor was also used during in-flight measurement. In-flight strain measurements from both the CNT fiber sensor and the strain gauge were continuously transmitted to the ground station and were compared with the flight data. Furthermore, an impact tester was installed inside the wing to simulate impact during flight, and in-flight impact measurements by the CNT fiber sensor were demonstrated.

Keywords

Acknowledgement

This work was supported by the Technology Innovation Program (10074278) funded by the Ministry of Trade, Industry & Energy (MI, Korea) and by the National Research Foundation of Korea (NRF) Grant funded by the Ministry of Science and ICT (NRF-2017R1A5A1015311).

References

  1. Alvarez-Montoya, J., Carvajal-Castrillon, A. and Sierra-Perez, J. (2019), "In-flight and wireless damage detection in a UAV composite wing using fiber optic sensors and strain field pattern recognition", Mech. Syst. Signal Process., 136, 106526. https://doi.org/10.1016/j.ymssp.2019.106526
  2. Botelho, E.C., Silva, R.A., Pardini, L.C. and Rezende, M.C. (2006), "A review on the development and properties of continuous fiber/epoxy/aluminum hybrid composites for aircraft structures", Mater. Res., 9(3), 247-256. http://dx.doi.org/10.1590/S1516-14392006000300002
  3. Hassan, M.H., Othman, A.R. and Kamaruddin, S (2017), "A review on the manufacturing defects of complex-shaped laminate in aircraft composite structures", Int. J. Adv. Manuf. Technol., 91, 4081-4094. https://doi.org/10.1007/s00170-017-0096-5
  4. Herszberg, I., Bannister, M.K., Li, H.C.H., Thomson, R.S. and White, C. (2007), "Structural health monitoring for advanced composite structures", Proceedings of the 16th International Conference on Composite Materials, Kyoto, Japan, July.
  5. Kim, K., Park, Y., Kim, Y.Y., Shrestha, P. and Kim, C.G. (2015), "Aircraft health and monitoring system for in-flight strain measurement of a wing structure", Smart Mater. Struct., 24(10), 105003. http://dx.doi.org/10.1088/0964-1726/24/10/105003
  6. Kressel, I., Hangelman, A., Botsev, Y., Balter, J., Guedj, P., Gorbatov, N., Tur, M., Pillai, A., Prasad, M.H., Gupta, N., Joseph, A.M. and Sundaram, R. (2012), "Evaluation of flight data from an airworthy structural health monitoring system integrally embedded in an unmanned air vehicle", Proceedings of the 6th European Workshop on Structural Health Monitoring, Dresden, Germany, July.
  7. Kwon, H., Park, Y., Kim, J. and Kim, C.G. (2019), "Embedded fiber Bragg grating sensor-based wing load monitoring system for composite aircraft", Struct. Health Monitor., 18(4), 1337-1351. https://doi.org/10.1177/1475921719843772
  8. Molent, L. and Aktepe, B. (2000), "Review of fatigue monitoring of agile military aircraft", Fatig. Fract. Eng. Mater. Struct., 23(9), 767-785. https://doi.org/10.1046/j.1460-2695.2000.00330.x
  9. On, S.Y., Park, S. and Kim, S.S. (2019), "Preparation and characterization of hybrid structured MWCNT/UHMWPE fiber sensors for strain sensing and load bearing of composite structures", Adv. Mater. Technol., 4(12), 1900807. https://doi.org/10.1002/admt.201900807
  10. Staszewki, W.J., Mahzan, S. and Traynor, R. (2009), "Health monitoring of aerospace structures-active and passive approach", Compos. Sci. Technol., 69(11-12), 1678-1685. https://doi.org/10.1016/j.compscitech.2008.09.034
  11. Takeda, S., Minakuchi, S., Okabe, Y. and Takeda, N. (2005), "Delamination monitoring of laminated composites subjected to low-velocity impact using small-diameter FBG sensors", Compos. Part A: Appl. Sci. Manuf., 36(7), 903-908. https://doi.org/10.1016/j.compositesa.2004.12.005
  12. Tang, A.N., Zhou, Z.T. and Cao, J.T. (2010), "A technique of landing gear loads calibration with strain gages", Proceedings of 27th International Congress of the Aeronautical Sciences, Nice, France, September.
  13. Zhou, D., Ha, D.S. and Inman, D.J. (2010), "Ultra low-power active wireless sensor for structural health monitoring", Smart Struct. Syst., Int. J., 6(5), 675-687. https://doi.org/10.12989/sss.2010.6.5_6.675
  14. Zhu, H., Wang, X., Liang, J., Lv, H., Tong, H., Ma, L., Hu, Y., Zhu, G., Zhang, T., Tie, Z., Liu, Z., Li, Q., Chen, L., Liu, J. and Jin, Z. (2017), "Versatile electronic skins for motion detection of joints enabled by aligned few-walled carbon nanotubes in flexible polymer composites", Adv. Funct. Mater., 27(21), 1606604. https://doi.org/10.1002/adfm.201606604