DOI QR코드

DOI QR Code

Addition of passive-carriage for increasing workspace of cable robots: automated inspection of surfaces of civil infrastructures

  • 투고 : 2020.07.16
  • 심사 : 2020.10.10
  • 발행 : 2021.02.25

초록

Cable-driven robots are parallel manipulators in which rigid links are replaced by actuated cables. The end-effector is then supported by a set of cables commanded by motors that are usually placed in a fixed frame. By varying the cables length, it is possible to change the end-effector position and/or orientation. Among the advantages presented by cable robots are they light-weight structure, high energy efficiency and their ability to cover large workspaces since cables are easy to wind. When high-speed operation is not required, a safer solution is to design cable-driven suspended robots, where all vertical components of cables tension are against gravity direction. Cable-driven suspended robots present limited workspace due to the elevated torque requirements for the higher part of the workspace. In this paper, the addition of a passive carriage in the top of the frame is proposed, allowing to achieve a much greater feasible workspace than the conventional one, i.e., with the same size as the desired inspection area while maintaining the same motor requirements. In the opposite, this new scheme presents non-desired vibration during the end-effector maneuvers. These vibrations can be removed by means of a more complex control strategy. Kinematics and dynamics models are developed in this paper. An analysis of sensor system is carried out and a control scheme is proposed for controlling the end-effector pose. Simulation and experimental results show that the feasible workspace can be notoriously increased while end-effector pose is controlled. This new architecture of cable-driven robot can be easily applied for automated inspection and monitoring of very large vertical surfaces of civil infrastructures, such as facades or dams.

키워드

과제정보

The research described in this paper was financially supported by Research Fund for Coal and Steel grant agreement No. 800687 in the framework of DESDEMONA project. Authors wish to thank the financial Support provided by the university of Castilla-La Mancha and the European Social Fund through the pre-doctoral funding [2019/451].

참고문헌

  1. Abbasnejad, G. and Carricato, M. (2012), "Real solutions of the direct geometrico-static problem of under-constrained cable-driven parallel robots with 3 cables: A numerical investigation", Meccanica, 47(7), 1761-1773. https://doi.org/10.1007/s11012-012-9552-3
  2. Adhikari, R.S., Bagchi, A. and Moselhi, O. (2014), "Automated condition assessment of concrete bridges with digital imaging", Smart Struct. Syst., Int. J., 13(6), 901-925. https://doi.org/10.12989/SSS.2014.13.6.901
  3. Arsenault, M. (2013), "Stiffness analysis of a planar 2-dof cable-suspended mechanism while considering cable mass", In: Cable-Driven Parallel Robots (pp. 405-421), Springer, Berlin, Heidelberg.
  4. Behzadipour, S. (2006), "Stiffness of cable-based parallel manipulators with application to stability analysis", J. Mech. Des., 128(1), 303-310. https://doi.org/10.1115/1.2114890
  5. BostelMan, R., Albus, J., Dagalakis, N. and Jacoff, A. (1996), "Robocrane project: an advanced concept for large scale manufacturing", In: AUVSI-PROCEEDINGS-, Citeseer, pp. 509-522.
  6. CableRobot Simulator (2020), "Cable-driven parallel robots - motion simulation in a new dimension", Accessed: 2020-07-02. http://www.ipa.fraunhofer.de/en/cabledriven_parallel_robots.html
  7. Castelli, G., Ottaviano, E. and Gonzalez, A. (2010), "Analysis and simulation of a new Cartesian cable-suspended robot", Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 224(8), 1717-1726. https://doi.org/10.1243/09544062JMES1976
  8. Castelli, G., Ottaviano, E. and Rea, P. (2014), "A Cartesian cable-suspended robot for improving end-users mobility in an urban environment", Robot. Comput.-Integr. Manuf., 30(3), 335-343. https://doi.org/10.1016/j.rcim.2013.11.001
  9. Castillo-Garcia, F.J., Rea, P., Gonzalez-Rodriguez, A. and Ottaviano, E. (2017), "On the Design of a 4 Degrees-of-freedom Pick and Place Cable Suspended Parallel Manipulator", Int. J. Robot. Automat. (IJRA), 6(4), 286-302. https://doi.org/10.11591/ijra.v6i4.pp286-302
  10. CoGiRo Project (2020), Accessed: 2020-07-10. http://www.lirmm.fr/cogiro/
  11. Cone, L.L. (1985), "Skycam-an aerial robotic camera system", Byte, 10(10), 122.
  12. Fattah, A. and Agrawal, S.K. (2002), "Workspace and design analysis of cable-suspended planar parallel robots", Proceedings of International Design Engineering Technical Conferences and Computers and Information in Engineering Conference, Vol. 36533, pp. 1095-1103.
  13. Feliu-Batlle, V. and Castillo-Garcia, F.J. (2014), "On the robust control of stable minimum phase plants with large uncertainty in a time constant, A fractional-order control approach", Automatica, 50(1), 218-224. https://doi.org/10.1016/j.automatica.2013.10.002
  14. Gonzalez-Rodriguez, A., Castillo-Garcia, F.J., Ottaviano, E., Rea, P. and Gonzalez-Rodriguez, A.G. (2017), "On the effects of the design of cable-Driven robots on kinematics and dynamics models accuracy", Mechatronics, 43, 18-27. http://dx.doi.org/10.1016/j.mechatronics.2017.02.002
  15. Gouttefarde, M. (2008), "Characterizations of fully constrained poses of parallel cable-driven robots: a review", Proceedings of International Design Engineering Technical Conferences and Computers and Information in Engineering Conference, Vol. 43260, pp. 21-30.
  16. Huang, T.L., Zhou, H., Chen, H.P. and Ren, W.X. (2016), "Stochastic modelling and optimum inspection and maintenance strategy for fatigue affected steel bridge members", Smart Struct. Syst., Int. J., 18(3), 569-584. https://doi.org/10.12989/SSS.2016.18.3.569
  17. Jeong, S., Lee, J., Cho, S. and Sim, S.H. (2019), "Integrated cable vibration control system using Arduino", Smart Struct. Syst., Int. J., 23(6), 695-702. https://doi.org/10.12989/sss.2019.23.6.695
  18. Jung, H.-J., Lee, J.-H., Yoon, S. and Kim, I.-H. (2019), "Bridge Inspection and condition assessment using Unmanned Aerial Vehicles (UAVs): Major challenges and solutions from a practical perspective", Smart Struct. Syst., Int. J., 24(5), 669-681. https://doi.org/10.12989/SSS.2019.24.5.669
  19. Kawamura, S., Choe, W., Tanaka, S. and Pandian, S.R. (1995), "Development of an ultrahigh speed robot falcon using wire drive system", In: Proceedings of IEEE International Conference on Robotics and Automation, 1, 215-220.
  20. Kawamura, S., Kino, H. and Won, C. (2000), "High-speed manipulation by using parallel wiredriven robots", Robotica, 18(1), 13-21. https://doi.org/10.1017/S0263574799002477
  21. Kim, C.W., Isemoto, R., McGetrick, P.J., Kawatani, M. and OBrien, E.J. (2014), "Drive-by bridge inspection from three different approaches", Smart Struct. Syst., Int. J., 13(5), 775-796. https://doi.org/10.12989/SSS.2014.13.5.775
  22. Lee, A.Y., Oh, J.K. and Choi, Y.J. (2010), "Bridge Inspection System using Robot", J. Korea Robot. Soc., 5(1), 77-84.
  23. Maloletov, A.V., Fadeev, M.Y. and Klimchik, A.S. (2019), "Error Analysis in Solving the Inverse Problem of the Cable-driven Parallel Underactuated Robot Kinematics and Methods for their Elimination", IFAC-PapersOnLine, 52(13), 1156-1161. https://doi.org/10.1016/j.ifacol.2019.11.352
  24. Merlet, J.-P. and dit Sandretto, J.A. (2015), "The forward kinematics of cable-driven parallel robots with sagging cables", In: Book; Cable-Driven 190 Parallel Robots Editors: Andreas Pott, Tobias Bruckmann. Proceedings of the Second International Conference on Cable-Driven Parallel Robots, Book Series: Mechanisms and Machine Science, 32, 3-15.
  25. Nan, R. (2006), "Five hundred meter aperture spherical radio telescope (fast)", Sci. China Series G, 49(2), 129-148. https://doi.org/10.1007/s11433-006-0129-9
  26. Ogata, K. (2010), Modern Control Engineering, Prentice hall
  27. Ottaviano, E. and Castelli, G. (2010), "A Study on the Effects of Cable Mass and Elasticity in Cable-Based Parallel Manipulators", Proceedings of the 18th CISM-IFToMM Symposium on Robot Design, Dynamics and Control, Springer Ed. Udine, pp. 149-156.
  28. Ottaviano, E., Arena, A., Gattulli, V. and Potenza, F. (2019), "Slackening effects in 2D exact positioning in cable-driven parallel manipulators", In: A. Pott, T. Bruckmann (Eds.), Mechanisms and Machine Science, Vol. 74 of Cable-Driven Parallel Robots. CableCon 2019, Springer, Cham, pp. 319-330.
  29. Pott, A. (2018a), "Kinematic Codes", In: Cable-Driven Parallel Robots, Springer Tracts in Advanced Robotics, Vol. 120, Springer, Cham.
  30. Pott, A. (2018b), "Kinematics with Nonstandard Cable Models", In: Cable-Driven Parallel Robots, Springer Tracts in Advanced Robotics, Vol. 120, Springer, Cham.
  31. Pott, A., Mutherich, H., Kraus, W., Schmidt, V., Miermeister, P., Dietz, T. and Verl, A. (2013), "Cable-driven parallel robots for industrial applications: The ipanema system family", Proceedings of the 44th International Symposium on Robotics (ISR), pp. 1-6.
  32. Pusey, J., Fattah, A., Agrawal, S. and Messina, E. (2004), "Design and workspace analysis of a 6-6 cable-suspended parallel robot", Mech. Mach. Theory, 39(7), 761-778. https://doi.org/10.1016/j.mechmachtheory.2004.02.010
  33. Roberts, R., Graham, T. and Lippitt, T. (1998), "On the inverse kinematics, statics, and fault tolerance of cable-suspended robots", J. Robot. Syst., 15(10), 581-597. https://doi.org/10.1002/(SICI)1097-4563(199810)15:10<581::AID-ROB4>3.0.CO;2-P
  34. Rubio-Gomez, G., Rodriguez-Rosa, D., Garcia-Vanegas, J.A., Gonzalez-Rodriguez, A., Castillo-Garcia, F.J. and Ottaviano, E. (2019), "Chain Driven Robots: An Industrial Application Opportunity. A Planar Case Approach", In: International Conference on Cable-Driven Parallel Robots, Springer, Cham, pp. 13-22.
  35. Skycam (2020), Accessed: 2020-07-10. https://en.wikipedia.org/wiki/Skycam
  36. Wang, Q., Kim, M.K., Sohn, H. and Cheng, J.C. (2016), "Surface flatness and distortion inspection of precast concrete elements using laser scanning technology", Smart Struct. Syst., Int. J., 18(3), 601-623. https://doi.org/10.12989/sss.2016.18.3.601
  37. Yangwen, X., Qi, L., Yaqing, Z. and Bin, L. (2010), "Model aerodynamic tests with a wire-driven parallel suspension system in low-speed wind tunnel", Chinese J. Aeronaut., 23(4), 393-400. https://doi.org/10.1016/S1000-9361(09)60233-8