DOI QR코드

DOI QR Code

Amplitude-dependent model updating of masonry buildings undergoing demolition

  • Martakis, Panagiotis (ETH Zurich (Department of Civil, Environmental and Geomatic Engineering, Chair of Structural Mechanics and Monitoring) ;
  • Reuland, Yves (ETH Zurich (Department of Civil, Environmental and Geomatic Engineering, Chair of Structural Mechanics and Monitoring) ;
  • Chatzi, Eleni (ETH Zurich (Department of Civil, Environmental and Geomatic Engineering, Chair of Structural Mechanics and Monitoring)
  • 투고 : 2020.07.21
  • 심사 : 2020.09.16
  • 발행 : 2021.02.25

초록

Precise knowledge of dynamic characteristics and data-driven inference of material properties of existing buildings are key for assessing their seismic capacity. While dynamic measurements on existing buildings are typically extracted under ambient conditions, masonry, in particular, exhibits nonlinear behavior at already very low shaking amplitudes. This implies that material properties, inferred via data-driven model updating under ambient conditions, may be inappropriate for predicting behavior under seismic actions. In addition, the relative amount of nonlinearity arising from structural behavior and soil-structure interaction are often unknown. In this work, Bayesian model updating is carried out on field measurements that are representative of increasing levels of shaking, as induced during demolition, on a pre-code masonry building. The results demonstrate that masonry buildings exhibit nonlinear behavior as the elastic modulus drops by up to 18% in the so-called equivalent elastic range, in which the observed frequency drop is reversible, prior to any visible sign of damage. The impact of this effect on the seismic assessment of existing structures is investigated via a nonlinear seismic analysis of the examined case study, calibrated under dynamic recordings of varying response amplitude. While limited to a single building, such changes in the inferred material properties results in a significant reduction of the safety factor, in this case by 14%.

키워드

과제정보

The research described in this paper was financially supported by the Real-time Earthquake Risk Reduction for a Resilient Europe 'RISE' project, financed under the European Union's Horizon 2020 research and innovation programme, under grant agreement No. 821115, as well as the ETH Grant (ETH-11 18-1) Dynarisk - "Enabling Dynamic Earthquake Risk Assessment". Authors would like to thank Kibag and Mr. Mario Sulz for granting access to the building during demolition, Professor Gramazio for providing valuable information regarding the examined building, Mr. Dominik Werne of the IBK Structures Lab for his valuable support in preparation of the monitoring equipment, and Mr. Martin Villanueva for his contribution to the equivalent-frame model.

참고문헌

  1. Allemang, R.J. (2003), "The modal assurance criterion-twenty years of use and abuse", Sound Vib., 37(8), 14-23.
  2. Altunisik, A.C., Karahasan, O.S., Genc, A.F., Okur, F.Y., Gunaydin, M. and Adanur, S. (2018), "Sensitivity-based model updating of building frames using modal test data", KSCE J. Civil Eng., 22(10), 4038-4046. https://doi.org/10.1007/s12205-018-1601-6
  3. Asgarieh, E., Moaveni, B. and Stavridis, A. (2012), "Nonlinear structural identification of a three-story infilled frame using instantaneous modal parameters", Topics in Modal Analysis II, 6, 669-674. https://doi.org/10.1007/978-1-4614-2419-2_66
  4. Astorga, A., Gueguen, P. and Kashima, T. (2018), "Nonlinear Elasticity Observed in Buildings during a Long Sequence of EarthquakesNonlinear Elasticity Observed in Buildings during a Long Sequence of Earthquakes", Bull. Seismol. Soc. America, 108(3A), 1185-1198. https://doi.org/10.1785/0120170289
  5. Atamturktur, S. and Laman, J.A. (2012), "Finite element model correlation and calibration of historic masonry monuments", Struct. Des. Tall Special Build., 21(2), 96-113. https://doi.org/10.1002/tal.577
  6. Bakir, P.G., Reynders, E. and De Roeck, G. (2007), "Sensitivitybased finite element model updating using constrained optimization with a trust region algorithm", J. Sound Vib., 305(1-2), 211-225. https://doi.org/10.1016/j.jsv.2007.03.044
  7. Bartoli, G., Betti, M., Facchini, L., Marra, A.M. and Monchetti, S. (2017), "Bayesian model updating of historic masonry towers through dynamic experimental data", Procedia Eng., 199, 1258-1263. https://doi.org/10.1016/j.proeng.2017.09.267
  8. Beck, J.L. and Au, S.K. (2002), "Bayesian updating of structural models and reliability using Markov chain Monte Carlo simulation", J. Eng. Mech., 128(4), 380-391. https://doi.org/10.1061/(ASCE)0733-9399(2002)128:4(380)
  9. Beck, J.L. and Katafygiotis, L.S. (1998), "Updating models and their uncertainties. I: Bayesian statistical framework", J. Eng. Mech., 124(4), 455-461. https://doi.org/10.1061/(ASCE)0733-9399(1998)124:4(455)
  10. Bedon, C. (2019), "Diagnostic analysis and dynamic identification of a glass suspension footbridge via on-site vibration experiments and FE numerical modelling", Compos. Struct., 216, 366-378. https://doi.org/10.1016/j.compstruct.2019.03.005
  11. Behmanesh, I., Moaveni, B. and Papadimitriou, C. (2017), "Probabilistic damage identification of a designed 9-story building using modal data in the presence of modeling errors", Eng. Struct., 131, 542-552. https://doi.org/10.1016/j.engstruct.2016.10.033
  12. Belmouden, Y. and Lestuzzi, P. (2009), "An equivalent frame model for seismic analysis of masonry and reinforced concrete buildings", Constr. Build. Mater., 23(1), 40-53. https://doi.org/10.1016/j.conbuildmat.2007.10.023
  13. Bracchi, S., Rota, M., Penna, A. and Magenes, G. (2015), "Consideration of modelling uncertainties in the seismic assessment of masonry buildings by equivalent-frame approach", Bull. Earthq. Eng., 13(11), 3423-3448. https://doi.org/10.1007/s10518-015-9760-z
  14. Brincker, R., Zhang, L. and Andersen, P. (2001), "Modal identification of output-only systems using frequency domain decomposition", Smart Mater. Struct., 10(3), 441-445. https://doi.org/10.1088/0964-1726/10/3/303
  15. Ceravolo, R., Matta, E., Quattrone, A. and Zanotti Fragonara, L. (2017), "Amplitude dependence of equivalent modal parameters in monitored buildings during earthquake swarms", Earthq. Eng. Struct. Dyn., 46(14), 2399-2417. https://doi.org/10.1002/eqe.2910
  16. Chatzis, M., Chatzi, E. and Smyth, A.W. (2015), "An experimental validation of time domain system identification methods with fusion of heterogeneous data", Earthq. Eng. Struct. Dyn., 44(4), 523-547. https://doi.org/10.1002/eqe.2528
  17. Cheng, L., Yang, J., Zheng, D., Li, B. and Ren, J. (2015), "The health monitoring method of concrete dams based on ambient vibration testing and kernel principle analysis", Shock Vib. https://doi.org/10.1155/2015/342358
  18. Cheung, S.H. and Beck, J.L. (2009), "Bayesian model updating using hybrid Monte Carlo simulation with application to structural dynamic models with many uncertain parameters", J. Eng. Mech., 135(4), 243-255. https://doi.org/10.1061/(ASCE)0733-9399(2009)135:4(243)
  19. Crowley, H., Despotaki, V., Rodrigues, D., Silva, V., Toma-Danila, D., Riga, E., Karatzetzou, A., Fotopoulou, S., Zugic, Z., Sousa, L. and Ozcebe, S. (2020), "Exposure model for European seismic risk assessment", Earthq. Spectra., 36(1), 252-273. https://doi.org/10.1177/8755293020919429
  20. CSI (2020), SAP2000 Integrated Software for Structural Analysis and Design, Computers and Structures Inc., Berkeley, CA, USA.
  21. De Sortis, A., Antonacci, E. and Vestroni, F. (2005), "Dynamic identification of a masonry building using forced vibration tests", Eng. Struct., 27(2), 155-165. https://doi.org/10.1016/j.engstruct.2004.08.012
  22. Diana, L., Thiriot, J., Reuland, Y. and Lestuzzi, P. (2019), "Application of association rules to determine building typological classes for seismic damage predictions at regional scale: the case study of Basel", Frontiers Built Environ., 5. https://doi.org/10.3389/fbuil.2019.00051
  23. Dobry, R., Gazetas, G. and Stokoe, K.H. (1986), "Dynamic response of arbitrarily shaped foundations: experimental verification", J. Geotech. Eng., 112(2), 136-154. https://doi.org/ 10.1061/(ASCE)0733-9410(1986)112:2(136)
  24. Fajfar, P. and Gaspersic, P. (1996), "The N2 method for the seismic damage analysis of RC buildings", Earthq. Eng. Struct. Dyn., 25(1), 31-46. https://doi.org/10.1002/(SICI)1096-9845 (199601)25:1<31::AID-EQE534>3.0.CO;2-V
  25. Foti, D., Gattulli, V. and Potenza, F. (2014), "Output-only identification and model updating by dynamic testing in unfavorable conditions of a seismically damaged building", Comput.-Aided Civil Infrastruct. Eng., 29, 659-675. https://doi.org/10.1111/mice.12071
  26. Gattulli, V., Antonacci, E. and Vestroni, F. (2013), "Field observations and failure analysis of the Basilica S. Maria di Collemaggio after the 2009 L'Aquila earthquake", Eng. Fail. Anal., 34, 715-134. http://dx.doi.org/10.1016/j.engfailanal.2013.01.020
  27. Gazetas, G. (1992), "Formulas and charts for impedances of surface and embedded foundations", J. Geotech. Eng., 117(9), 1363-1381. https://doi.org/10.1061/(ASCE)0733-9410(1991)117:9(1363)
  28. Gelman, A., Carlin, J.B., Stern, H.S., Dunson, D.B., Vehtari, A. and Rubin, D.B. (2014), Bayesian Data Analysis, Texts in Statistical Science, Boca Raton, FL, USA.
  29. Goodman, J. and Weare, J. (2010), "Ensemble samplers with affine invariance", Commun. Appl. Mathe. Computat. Sci., 5(1), 65-80. https://doi.org/10.2140/camcos.2010.5.65
  30. Jaishi, B. and Ren, W.X. (2005), "Structural finite element model updating using ambient vibration test results", J. Struct. Eng., 131(4), 617-628. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:4(617)
  31. Jensen, H.A., Millas, E., Kusanovic, D. and Papadimitriou, C. (2014), "Model-reduction techniques for Bayesian finite element model updating using dynamic response data", Comput. Methods Appl. Mech. Eng., 279, 301-324. http://dx.doi.org/10.1016/j.cma.2014.06.032
  32. Juang, J.N. and Pappa, R.S. (1985), "An eigensystem realization algorithm for modal parameter identification and model reduction", J. Guidance Control Dyn., 8(5), 620-627. http://dx.doi.org/10.2514/3.20031
  33. Kenny, C. (2009), "Why do people die in earthquakes? The costs, benefits and institutions of disaster risk reduction in developing countries", Research Report No. 4823, The World Bank Sustainable Development Network Finance Economics & Urban Department.
  34. Kouris, L.A.S., Penna, A. and Magenes, G. (2017), "Seismic damage diagnosis of a masonry building using short-term damping measurements", J. Sound Vib., 394, 366-391. https://doi.org/10.1016/j.jsv.2017.02.001
  35. Lagomarsino, S., Penna, A., Galasco, A. and Cattari, S. (2013), "TREMURI program: an equivalent frame model for the nonlinear seismic analysis of masonry buildings", Eng. Struct., 56, 1787-1799. http://dx.doi.org/10.1016/j.engstruct.2013.08.002
  36. Lam, H.F., Hu, J. and Yang, J.H. (2017), "Bayesian operational modal analysis and Markov chain Monte Carlo-based model updating of a factory building", Eng. Struct., 132, 314-336. https://doi.org/10.1016/j.engstruct.2016.11.048
  37. Lam, H.F., Hu, J. and Adeagbo, M.O. (2019), "Bayesian model updating of a 20-story office building utilizing operational modal analysis results", Adv. Struct. Eng., 22(16), 3385-3394. https://doi.org/10.1177%2F1369433218825043 https://doi.org/10.1177%2F1369433218825043
  38. Lombaert, G., Moaveni, B., He, X. and Conte, J.P. (2009), "Damage identification of a seven-story reinforced concrete shear wall building using Bayesian model updating", Proceedings of the IMAC-XXVII, Orlado, FL, USA, February.
  39. Lourenco, P.B. and Roque, J.A. (2006), "Simplified indexes for the seismic vulnerability of ancient masonry buildings", Constr. Build. Mater., 20(4), 200-208. https://doi.org/10.1016/j.conbuildmat.2005.08.027
  40. Ma, G. and Li, H. (2015), "Experimental study of the seismic behavior of predamaged reinforced-concrete columns retrofitted with basalt fiber-reinforced polymer", J. Compos. Constr., 19(6), 04015016. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000572
  41. Marino, S., Cattari, S. and Lagomarsino, S. (2019), "Are the nonlinear static procedures feasible for the seismic assessment of irregular existing masonry buildings?", Eng. Struct., 200, 109700. https://doi.org/10.1016/j.engstruct.2019.109700
  42. Marelli, S. and Sudret, B. (2014), "UQLab: A framework for uncertainty quantification in Matlab", Proceedings of the 2nd International Conference on Vulnerability, Risk Analysis and Management (ICVRAM2014), Liverpool, UK.
  43. Martakis, P., Taeseri, D., Chatzi, E. and Laue, J. (2017), "A centrifuge-based experimental verification of Soil-Structure Interaction effects", Soil Dyn. Earthq. Eng., 103, 1-14. https://doi.org/10.1016/j.soildyn.2017.09.005
  44. Martakis, P., Dertimanis, V. and Chatzi, E. (2019), "Baudynamische Bemessung & Identifizierung einer Aufgehangten Treppenkonstruktion", Proceedings of the 16th. D-A-CH Tagung Erdbebeningenieurwesen & Baudynamik (D-ACH 2019), Innsbruck, Austria.
  45. Michel, C., Gueguen, P. and Bard, P.Y. (2008), "Dynamic parameters of structures extracted from ambient vibration measurements: An aid for the seismic vulnerability assessment of existing buildings in moderate seismic hazard regions", Soil Dyn. Earthq. Eng., 28(8), 593-604. https://doi.org/10.1016/j.soildyn.2007.10.002
  46. Michel, C., Zapico, B., Lestuzzi, P., Molina, F.J. and Weber, F. (2011), "Quantification of fundamental frequency drop for unreinforced masonry buildings from dynamic tests", Earthq. Eng. Struct. Dyn., 40(11), 1283-1296. https://doi.org/10.1002/eqe.1088
  47. Muto, M. and Beck, J.L. (2008), "Bayesian updating and model class selection for hysteretic structural models using stochastic simulation", J. Vib. Control, 14(1-2), 7-34. https://doi.org/10.1177/1077546307079400
  48. OPCM 3274 (2003), Primi elementi in materia di criteri generali per la classificazione sismica del territorio nazionale e di normative tecniche per le costruzioni in zona sismica.
  49. Pai, S.G., Reuland, Y. and Smith, I.F.C. (2019), "Data-Interpretation Methodologies for Practical Asset-Management", J. Sensor Actuator Networks, 8(2), 36. https://doi.org/10.3390/jsan8020036
  50. Papadimitriou, C., Ntotsios, E., Giagopoulos, D. and Natsiavas, S. (2011), "Variability of updated finite element models and their predictions consistent with vibration measurements", Struct. Control Health Monitor., 19(5), 630-654. https://doi.org/10.1002/stc.453
  51. Penelis, G.G. (2006), "An efficient approach for pushover analysis of unreinforced masonry (URM) structures", J. Earthq. Eng., 10(3), 359-379. https://doi.org/10.1080/13632460609350601
  52. Peterson, L.D. (1995), "Efficient computation of the Eigensystem realization algorithm", J. Guidance Control Dyn., 18(3), 395-403. https://doi.org/10.2514/3.21401
  53. Quagliarini, E., Maracchini, G. and Clementi, F. (2017), "Uses and limits of the Equivalent Frame Model on existing unreinforced masonry buildings for assessing their seismic risk: A review", J. Build. Eng., 10, 166-182. https://doi.org/10.1016/j.jobe.2017.03.004
  54. Reuland, Y., Lestuzzi, P. and Smith, I.F. (2017a), "Data-interpretation methodologies for non-linear earthquake response predictions of damaged structures", Frontiers Built Environ., 3, 43. https://doi.org/10.3389/fbuil.2017.00043
  55. Reuland, Y., Jaoude, A.A., Lestuzzi, P. and Smith, I.F. (2017b), "Usefulness of ambient-vibration measurements for seismic assessment of existing structures", Proceedings of the 4th International Conference on Smart Monitoring, Assessment and Rehabilitation of Civil Structures, Zurich, Switzerland.
  56. Reuland, Y., Lestuzzi, P. and Smith, I.F.C. (2019a), "Measurement-based support for post-earthquake assessment of buildings", Struct. Infrastruct. Eng., 15(5), 647-662. https://doi.org/10.1080/15732479.2019.1569071
  57. Reuland, Y., Lestuzzi, P. and Smith, I.F. (2019b), "An engineering approach to model-class selection for measurement-supported post-earthquake assessment", Eng. Struct., 197, 109408. https://doi.org/10.1016/j.engstruct.2019.109408
  58. SIA 261 (2014), Einwirkungen auf Tragwerke, Swiss Society of Engineers and Architects: Zurich, Switzerland.
  59. SIA 266 (2015), Mauerwerk, Swiss Society of Engineers and Architects: Zurich, Switzerland.
  60. SIA 269/6 (2014), Erhaltung von Tragwerken - Mauerwerksbau, Teil 2: Mauerwerk aus kunstlichen Steinen, Swiss Society of Engineers and Architects: Zurich, Switzerland.
  61. SIA 269/8 (2017), Erhaltung von Tragwerken - Erdbeben, Swiss Society of Engineers and Architects: Zurich, Switzerland.
  62. Simoen, E., De Roeck, G. and Lombaert, G. (2015), "Dealing with uncertainty in model updating for damage assessment: A review", Mech. Syst. Signal Process., 56, 123-149. https://doi.org/10.1016/j.ymssp.2014.11.001
  63. Snoj, J., Osterreicher, M. and Dolsek, M. (2013), "The importance of ambient and forced vibration measurements for the results of seismic performance assessment of buildings obtained by using a simplified non-linear procedure: case study of an old masonry building", Bull. Earthqu. Eng., 11, 2105-2132. https://doi.org/10.1007/s10518-013-9494-8
  64. Song, M., Behmanesh, I., Moaveni, B. and Papadimitriou, C. (2019a), "Modeling error estimation and response prediction of a 10-story building model through a hierarchical Bayesian model updating framework", Frontiers Built Environ., 5. https://doi.org/10.3389/fbuil.2019.00007
  65. Song, M., Moaveni, B., Papadimitriou, C. and Stavridis, A. (2019b), "Accounting for amplitude of excitation in model updating through a hierarchical Bayesian approach: Application to a two-story reinforced concrete building", Mech. Syst. Signal Process., 123, 68-83. https://doi.org/10.1016/j.ymssp.2018.12.049
  66. Soyoz, S., Taciroglu, E., Orakcal, K., Nigbor, R., Skolnik, D., Lus, H. and Safak, E. (2013), "Ambient and forced vibration testing of a reinforced concrete building before and after its seismic retrofitting", J. Struct. Eng., 139(10), 1741-1752. http://dx.doi.org/10.1061/(ASCE)ST.1943-541X.0000568
  67. Spencer, B.J., Finholt, T.A., Foster, I., Kesselman, C., Beldica, C., Futrelle, J., Gullapalli, S., Hubbard, P., Liming, L., Marcusiu, D., Pearlman, L., Severance, C. and Yang, G. (2004a), "NEESGRID: a distributed collaboratory for advanced earthquake engineering experiment and simulation", Proceedings of the 13th World Conference on Earthquake Engineering, Vancouver, B.C., Canada, August.
  68. Spencer, B.J., Ruiz-Sandoval, M.E. and Kurata, N. (2004b), "Smart sensing technology: opportunities and challenges", Struct. Control Health Monitor., 11, 349-368. https://doi.org/10.1002/stc.48
  69. Stavridis, A., Koutromanos, I. and Shing, P.B. (2011), "Shake-table tests of a three-story reinforced concrete frame with masonry infill walls", Earthq. Eng. Struct. Dyn., 41(6), 1089-1108. https://doi.org/10.1002/eqe.1174
  70. Steiger, R., Feltrin, G., Weber, F., Nerbano, S. and Motavalli, M. (2015), "Experimental modal analysis of a multi-storey light-frame timber building", Bull. Earthq. Eng., 15(8), 3265-3291. https://doi.org/10.1007/s10518-015-9828-9
  71. Straub, D. and Papaioannou, I. (2015), "Bayesian updating with structural reliability methods", J. Eng. Mech., 141(3), 04014134. https://doi.org/10.1061/(ASCE)EM.1943-7889.0000839
  72. Studer, J.A., Laue, J. and Koller, M.G. (2007), Bodendynamik, Springer-Verlag Berlin, Heidelberg, Germany.
  73. Tarantola, A. (2006), "Popper, Bayes and the inverse problem", Nature Phys., 15, 3265-3291. https://doi.org/10.1038/nphys375
  74. Ulusoy, H.S., Feng, M.Q. and Fanning, P.J. (2010), "System identification of a building from multiple seismic records", Earthq. Eng. Struct. Dyn., 40, 661-674. https://doi.org/ 10.1002/eqe
  75. Van Overschee, P. and De Moor, B. (1996), "Continuous-time frequency domain subspace system identification", Signal Processing, 52(2), 179-194. https://doi.org/10.1016/0165-1684(96)00052-7
  76. Vanik, M.W., Beck, J.L. and Au, S. (2000), "Bayesian probabilistic approach to structural health monitoring", J. Eng. Mech., 126(7), 738-745. https://doi.org/10.1061/(ASCE)0733-9399(2000)126:7(738)
  77. Vidal, F., Navarro, M., Aranda, C. and Enomoto, T. (2014), "Changes in dynamic characteristics of Lorca RC buildings from pre-and post-earthquake ambient vibration data", Bull. Earthq. Eng., 12(5), 2095-2110. https://doi.org/10.1007/s10518-013-9489-5
  78. Wagner, P.R., Nagel, J., Marelli, S. and Sudret, B. (2019), "UQLab user manual - Bayesian inference for model calibration and inverse problems", Report No. UQLab-V1.3-113, Chair of Risk, Safety and Uncertainty Quantification, ETH Zurich, Switzerland.
  79. World Economic Forum (2016), "Shaping the Future of Construction A Breakthrough in Mindset and Technology", World Economic Forum: Cologny, Switzerland.
  80. Yu, E., Skolnik, D., Whang, D.H. and Wallace, J.W. (2006), "Forced vibration testing of a four story RC building utilizing the nees@ucla mobile field laboratory", Proceedings of the 8th U.S. National Conference on Earthquake Engineering, San Francisco, CA, USA.