DOI QR코드

DOI QR Code

Bond-slip behaviour of H-shaped steel embedded in UHPFRC

  • Huang, Zhenyu (Guangdong Provincial Key Laboratory of Durability for Marine Civil Engineering, Shenzhen University) ;
  • Huang, Xinxiong (Guangdong Provincial Key Laboratory of Durability for Marine Civil Engineering, Shenzhen University) ;
  • Li, Weiwen (Guangdong Provincial Key Laboratory of Durability for Marine Civil Engineering, Shenzhen University) ;
  • Chen, Chufa (Guangdong Provincial Key Laboratory of Durability for Marine Civil Engineering, Shenzhen University) ;
  • Li, Yongjie (Guangdong Provincial Key Laboratory of Durability for Marine Civil Engineering, Shenzhen University) ;
  • Lin, Zhiwei (Guangdong Provincial Key Laboratory of Durability for Marine Civil Engineering, Shenzhen University) ;
  • Liao, Wen-I (Department of Civil Engineering, National Taipei University of Technology)
  • 투고 : 2019.05.15
  • 심사 : 2021.02.14
  • 발행 : 2021.03.10

초록

The present study experimentally and analytically investigated the push-out behaviour of H-shaped steel section embedded in ultrahigh-performance fibre-reinforced concrete (UHPFRC). The effect of significant parameters such as the concrete types, fibre content, embedded steel length, transverse reinforcement ratio and concrete cover on the bond stress, development of bond stress along the embedded length and failure mechanism has been reported. The test results show that the bond slip behaviour of steel-UHPFRC is different from the bond slip behaviour of steel-normal concrete and steel-high strength concrete. The bond-slip curves of steel-normal concrete and steel-high strength concrete exhibit brittle behaviour, and the bond strength decreases rapidly after reaching the peak load, with a residual bond strength of approximately one-half of the peak bond strength. The bond-slip curves of steel-UHPFRC show an obvious ductility, which exhibits a unique displacement pseudoplastic effect. The residual bond strength can still reach from 80% to 90% of the peak bond strength. Compared to steel-normal concrete, the transverse confinement of stirrups has a limited effect on the bond strength in the steel-UHPFRC substrate, but a higher stirrup ratio can improve cracking resistance. The experimental campaign quantifies the local bond stress development and finds that the strain distribution in steel follows an exponential rule along the steel embedded length. Based on the theory of mean bond and local bond stress, the present study proposes empirical approaches to predict the ultimate and residual bond resistance with satisfactory precision. The research findings serve to explain the interface bond mechanism between UHPFRC and steel, which is significant for the design of steel-UHPFRC composite structures and verify the feasibility of eliminating longitudinal rebars and stirrups by using UHPFRC in composite columns.

키워드

참고문헌

  1. AASHTO (2012), AASHTO LRFD bridge design specifications, Customary U.S. Units (6th Ed.); American Association of State Highway and Transportation Officials, Washington, DC, USA.
  2. ACI 318 (2014), Building Code Requirements for Structural Concrete, American Concrete Institute, Farmington Hills, MI48331, USA.
  3. AFGC (2002), Ultra high performance fibre-reinforced concretes Interim recommendations, Association Francaise de Genie Civil; Bagneux, France.
  4. AIJ (1991), Standards for structural calculation of steel reinforced concrete structures, Architectural Institute of Japan, Shiba, Japan.
  5. ANSI-AISC 360-10 (2010). Specification for Structural Steel Buildings, Chicago, IL, USA
  6. Analytical approach to investigate sandwich plate frequency considering effects of elastic foundation and temperature change. Struct Eng Mech.
  7. ASTM C136 / C136M-14 (2014), Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates, West Conshohocken, PA, USA.
  8. ASTM C1611/C1611-14 (2014), Standard test method for slump flow of self-consolidating concrete, West Conshohocken, PA, USA
  9. Bruhwiler, E. (2016), "Structural UHPFRC":Welcome to the Post-concrete Era", Proceedings of the 1stInternational Interactive Symposium on UHPC. Des Moines:Lowa State University.
  10. Buttignol, T.E.T., Sousa, J.L.A.O. and Bittencourt, T.N. (2017), "Ultra High-Performance Fiber-Reinforced Concrete (UHPFRC): a review of material properties and design procedures", Revista IBRACON de Estruturas e Materiais., 10(4), 957-971. https://doi.org/10.1590/s1983-41952017000400011
  11. Choi, E., Chae, S.W., Park, H., Nam, T.H.(2018a), "Investigating Self-Centering Capacity of Superelastic Shape Memory Alloy Fibers with Different Anchorages Through Pullout Tests", J. Nanosci. Nanotechnol., 18(9), 6228-6232. https://doi.org/10.1166/jnn.2018.15635.
  12. Choi, E., Mohammadzadeh, B., Hwang, J.H. and Kim, W.J.(2018b), "Pullout behavior of superelastic SMA fibers with various end-shapes embedded in cement mortar", Constr. Build. Mater., 167, 605-616. https://doi.org/10.1016/j.conbuildmat.2018.02.070.
  13. Choi, E., Mohammadzadeh, B., Kim, D.K. and Jeon, J.S.(2018c), "A new experimental investigation into the effects of reinforcing mortar beams with superelastic SMA fibers on controlling and closing cracks", Compos Part B: Eng., 137, 140-152. https://doi.org/10.1016/j.compositesb.2017.11.017.
  14. Choi, E., Mohammadzadeh, B. and Kim, H.S. (2018d), "SMA bending bars as self-centering and damping devices", Smart Mater Struct., 28, 025029 https://doi.org/10.1088/1361-665X/aaf5e3
  15. Eurocode4 (2004), EN 1994-1-1, Design of composite steel and concrete structures, European Committee for Standardisation; Brussels, Belgium.
  16. Gu, C., Ye, G. and Sun, W. (2015), "Ultrahigh performance concrete-properties, applications and perspectives", Sci China Technol Sc., 58, 587-599. https://doi.org/10.1007/s11431-015-5769-4
  17. GB/T 31387-2015 (2015), Reactive powder concrete, Standardization Administration of China; Beijing, China.
  18. GB 50164-92 (1992), Standard of quality control of concrete, Standardization Administration of China; Beijing, China.
  19. Hassan, A.M.T., Jones, S.W. and Mahmud, G.H. (2012), "Experimental test methods to determine the uniaxial tensile and compressive behaviour of ultra high performance fibre reinforced concrete (UHPFRC)", Constr. Build. Mater., 37, 874-882. https://doi.org/10.1016/j.conbuildmat.2012.04.030.
  20. Huang, H., Gao, X., Li, L. and Wang, H. (2018), "Improvement effect of steel fiber orientation control on mechanical performance of UHPC", Constr. Build. Mater., 188, 709-721. https://doi.org/10.1016/j.conbuildmat.2018.08.146.
  21. Huang, Z., Huang, X., Li, W., Mei, L. and Liew, J.Y.R. (2019), "Experimental behavior of VHSC encased composite stub column under compression and end moment", Steel Compos Struct., 31(1), 69-83. https://doi.org/10.12989/scs.2019.31.1.069.
  22. Huang, Z., Huang, X., Li, W., Zhang, J. (2020), "Compressive resistance behavior of UHPFRC encased steel composite stub column", Steel Compos Struct., 37(2), 211-227. https://doi.org/10.12989/scs.2020.37.2.211.
  23. Design Guidelines for K-UHPC (2012), Korea Concrete Institute, Seoul. South Korea.
  24. JGJ 138-2016 (2016), Code for design of composite structures, Ministry of Housing and Urban-Rural Construction of the People's Republic of China; Beijing, China
  25. JSCE (2008), Recommendations for Design and Construction of High Performance Fiber Reinforced Cement Composites with Multiple Fine Cracks (HPFRCC), Japan Society of Civil Engineers; Tokyo, Japan
  26. Kim, C.S., Park, H.G., Chung, K.S. and Choi, I.R. (2012), "Eccentric Axial Load Testing for Concrete-Encased Steel Columns Using 800 MPa Steel and 100 MPa Concrete", J Struct Eng., 138(8), 1019-1031. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000533.
  27. Li, H. (1998), Experimental study on Bond behavior of Steel-reinforced High-strength concrete structure and Shear behavior of beam-column Joint, Tongji University, Shanghai, China.
  28. Marchand, P., Baby, F., Khadour, A., Battesti, T., Rivillon, P., Quiertant, M., Nguyen, H.H., Genereux, G., Deveaud, J.P., Simon, A. and Toutlemonde, F. (2015), "Bond behaviour of reinforcing bars in UHPFRC", Mater Struct., 49(5), 1979-1995. https://doi.org/10.1617/s11527-015-0628-0
  29. Mohammadzadeh, B. and Noh, H.C. (2017), "Analytical method to investigate nonlinear dynamic responses of sandwich plates with FGM faces resting on elastic foundation considering blast loads", Compos Struct., 174, 142-157. https://doi.org/10.1016/j.compstruct.2017.03.087.
  30. Mohammadzadeh, B., Bina, M. and Hasounizadeh, H. (2011), "Application and comparison of mathematical and physical models on inspecting slab of stilling basin floor under static and dynamic forces", Appl. Mech. Mater., 147, 283-287. https://doi.org/10.4028/www.scientific.net/AMM.147.283.
  31. Muazzam, G.S., Ben, W., Amit, J., Ramazan, K., Nesibe, G.O., Bora, G., Mina, D. and Abdeldjelil, B. (2018), "Advancements in Concrete Mix Designs High-Performance and UltrahighPerformance Concretes from 1970 to 2016", J. Mater. Civ. Eng., 30(3), 04017310. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002144.
  32. Randl, N., Steiner, T., Ofner, S., Baumgartner, E. and Meszoly, T. (2014), "Development of UHPC mixtures from an ecological point of view", Constr. Build. Mater., 67, 373-378. https://doi.org/10.1016/j.conbuildmat.2013.12.102.
  33. Roeder, C.W., Robert, C. and Colin, B.B. (1999), "Shear Connector Requirement for Embedded Sections", J. Struct. Eng., 125(2), 142-151. https://doi.org/10.1061/(ASCE)0733-9445(1999)125:2(142).
  34. Shin, H.O., Lee, S.J. and Yoo, D.Y. (2018), "Bond Behavior of Pretensioned Strand Embedded in Ultra-High Performance Fiber-Reinforced Concrete", Int. J. Concr. Struct. M., 12(1), 34. https://doi.org/10.1186/s40069-018-0249-4
  35. SIA (2016), SIA 2052, UHPFRC - Materials, design and construction, Kassel, Germany.
  36. Tao, Z. and Yu, Q. (2012), "Residual Bond Strength in Steel Reinforced Concrete Columns after Fire Exposure", Fire Saf. J., 53, 19-27. https://doi.org/10.1016/j.firesaf.2012.06.010.
  37. Wang, W.H., et al. (2017), "Tests on the Steel-Concrete Bond Strength in Steel Reinforced Concrete (SRC) Columns After Fire Exposure", Fire Technol., 53(2), 917-945. https://doi.org/10.1007/s10694-016-0610-6
  38. Wang, W.H., Han, L.H., Tan, Q.H. and Tao, Z. (2016), "Tests on the Steel-Concrete Bond Strength in Steel Reinforced Concrete (SRC) Columns After Fire Exposure", Fire Technol., 53(2), 917-945. https://doi.org/10.1007/s10694-016-0610-6
  39. Wille, K., El-Tawil, S. and Naaman, A.E. (2014), "Properties of strain hardening ultra high performance fiber reinforced concrete (UHP-FRC) under direct tensile loading", Cement Concrete Compos., 48, 53-66. https://doi.org/10.1016/j.cemconcomp.2013.12.015.
  40. Wium, J.A. and Lebet, J.-P. (1994), "Simplified calculation method for force transfer in composite columns", J. Struct. Eng., 120(3), 728-746. https://doi.org/10.1061/(ASCE)0733-9445(1994)120:3(728).
  41. Wium, J. and Lebet, J.P.. (1992), Force Transfer in Composite Columns. Composite Construction in Steel & Concrete II, An Engineering Foundation Conference. New York, American Society of Civil Engineers.
  42. Xu, J., Wua, C., Xiang, H., Su, Y., Li, Z.X., Fang, Q., Hao, H., Liu, Z., Zhang, Y. and Li, J. (2016), "Behaviour of ultra high performance fibre reinforced concrete columns subjected to blast loading", Eng Struct., 118, 97-107. https://doi.org/10.1016/j.engstruct.2016.03.048.
  43. Yang, Y., Guo, Z., Xue, J., Zhao, H. and Nie, J. (2006), "Experimental study on bond-slip behavior of steel reinforced concrete", J. Build. Struct., 4(26), 1-9.
  44. Ying, W. (2014), "Experimental research and theoretical analysis on bond-slip of H-shaped steel and high strength concrete surface", Disertation, Xi'an University of architecture and technology, Xi'an, China.
  45. Yoo, D.Y. and Banthia, N. (2016), "Mechanical properties of ultra-high-performance fiber-reinforced concrete A review", Cement Concrete Compos., 73, 267-280. https://doi.org/10.1016/j.cemconcomp.2016.08.001.
  46. Yoo, D.Y., Kwon, K.Y., Park, J.J. and Yoon, Y.S. (2015), "Local bond-slip response of GFRP rebar in ultra-high-performance fiber-reinforced concrete", Compos. Struct., 120, 53-64. https://doi.org/10.1016/j.compstruct.2014.09.055.
  47. Yoo, D.Y. and Yoon, Y.S. (2015), "Structural performance of ultra-high-performance concrete beams with different steel fibers", Eng. Struct., 102, 409-423. https://doi.org/10.1016/j.engstruct.2015.08.029.
  48. Yoo, D.Y. and Yoon, Y.S. (2016), "Bond behavior of GFRP and steel bars in ultra-high-performance fiber-reinforced concrete", Adv. Compos. Mater., 26(6), 493-510. https://doi.org/10.1080/09243046.2016.1197493.
  49. Yoo, D.Y. and Yoon, Y.S. (2016), "A Review on Structural Behavior, Design, and Application of Ultra-High-Performance Fiber-Reinforced Concrete", Int. J. Concr. Struct. M., 10(2), 125-142. https://doi.org/10.1007/s40069-016-0143-x
  50. Yu, R., Spiesz, P. and Brouwers, H.J.H. (2014), "Mix design and properties assessment of Ultra-High Performance Fibre Reinforced Concrete (UHPFRC)", Cement Concrete Res., 56, 29-39. https://doi.org/10.1016/j.cemconres.2013.11.002.
  51. Zheng, H., Chen, Z. and Xu, J. (2016), "Bond behavior of H-shaped steel embedded in recycled aggregate concrete under push-out loads", Int. J. Steel Struct., 16(2), 347-360. https://doi.org/10.1007/s13296-016-6008-y
  52. Zheng, S., Yang, Y., Xue, J., Yu, M. and Zhao, H. (2002), "Study on bond-slip behavior of steel reinforced concrete", China Civil Eng. J., 4(35), 48-51.
  53. Zheng, S., Yang, Y., Yu, M.-H. and Zhang, J. (2003), "Experimental study on bond-slip behavior of steel reinforced concrete structures", Eng. Mech., 5(20), 63-65.
  54. Zhou, X., Yan, B. and Liu, J. (2015), "Behavior of square tubed steel reinforced-concrete (SRC) columns under eccentric compression", Thin Wall. Struct., 91, 129-138. https://doi.org/10.1016/j.tws.2015.01.022.