DOI QR코드

DOI QR Code

Strength Characteristics of 3D Printed Composite Materials According to Lamination Patterns

적층 패턴에 따른 3D 프린팅 복합재료의 강도특성

  • 서은아 (한국건설기술연구원 구조연구본부) ;
  • 이호재 (한국건설기술연구원 구조연구본부) ;
  • 양근혁 (경기대학교 스마트시티공학부 건축공학전공)
  • Received : 2021.10.29
  • Accepted : 2021.11.09
  • Published : 2021.12.31

Abstract

In this study, the rheological characteristics and of 3D printing composite materials and the compressive strength characteristics according to the lamination patterns were evaluated. As a result of rheology test, rapid material change was observed after 60 minutes of extrusion, yielding stress 1.4 times higher than immediately after mixing, and plastic viscosity was 14.94-25.62% lower. The compressive strength of the specimens manufactured in the mold and the laminated specimens were compared, and the lamination pattern of the laminated specimens were 0°, 45°, and 90° as variables. The compressive strength of the mold casting specimen and the laminated specimen from 1 to 28 days of age showed similar performance regardless of the lamination pattern. In particular, at the age of 28 days, the modulus of elasticity, maximum compressive strength, and strain at maximum stress of all specimens were almost the same. In order to analyze the interface of the laminated specimens, X-ray CT analysis of the specimen whose compressive strength were measured was performed. Through CT analysis, it was confirmed that cracks did not occur at the lamination interface, which can be judged that the interface in the laminated specimen behaved in an integrated manner.

이 연구에서는 3D 프린팅 복합재료의 레올로지 특성과 출력 패턴에 따른 적층 시험체의 압축강도 특성을 평가하였다. 레올로지 측정결과, 압출 후 60분 후부터 급격한 재료 변화가 나타났으며, 배합직후 대비 1.4배 높은 항복응력과 14.94~25.62% 낮은 소성점도를 나타내었다. 실린더 몰드에 제작한 시험체와 적층 시험체의 압축강도를 비교하였으며, 적층 시험체의 출력패턴은 0°, 45°, 90°를 변수로 하였다. 재령 1~28일까지의 몰드 타설 시험체와 적층 시험체의 압축강도는 출력 패턴과 관계없이 유사한 성능을 나타내었다. 특히, 재령 28일에서는 모든 시험체의 초기 접선탄성계수와 최고 압축강도 및 최대 응력 시 변형률은 거의 동일하게 나타났다. X-ray CT분석을 통한 적층 시험체의 계면 분석결과, 압축강도 측정 후의 시험체의 적층 계면에서의 균열이 발생하지 않은 것을 확인하였으며, 이는 적층 시험체 내의 각각의 계면이 일체화 거동을 한 것으로 판단할 수 있다.

Keywords

Acknowledgement

이 논문은 2021년 해양수산부 재원으로 해양수산과학기술진흥원의 지원을 받아 수행된 연구임(과제명: 수중 적층 타설용 콘크리트 복합재료 개발, 과제번호: 2020555)

References

  1. A. Alwi, S. Karayiannis, B. Starkey, M. Gardner, K. Reodique, T. Varley (2013), Contrucktion, MegaScale 3D Printing, MegaScale 3D Printing, University of SURREY, p. 199.
  2. ASTM Standard C39 Committee, Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens, ASTM Standard International,
  3. Heras Murcia, D., Genedy, M., and Reda Taha, M.M. (2020), Examining the significance of infill printing pattern on the anisotropy of 3D printed concrete, Construction & Building Materials, 262, 120559 https://doi.org/10.1016/j.conbuildmat.2020.120559
  4. Lee, H. J., Kim, J. H., Moon, J. H., Kim, W. W., and Seo, E. A. (2019 a), Correlation between pore characteristics and tensile bond strength of additive manufactured mortar using X-ray computed tomography, Construction & Building Materials, 226, 712-720 https://doi.org/10.1016/j.conbuildmat.2019.07.161
  5. Lee, H. J., Kim, J. H., Moon, J. H., Kim, W. W., and Seo, E. A. (2020), Effect of Shrinkage Characteristics of Cement-Based Composites by Extrusion and Lamination Process of Construction 3D Printing, Journal of the Korea Institute for Structural Maintenance and Inspection, 24(.6), 113-118 https://doi.org/10.11112/JKSMI.2020.24.6.113
  6. Lee, Y. Y., Song, J. S., Choi, S. H., and Kim, K. S. (2019 b), Buildability for Concrete 3D Printing According to Printing Time Gap, Journal of the Korea Institute for Structural Maintenance and Inspection, 23(4), 131-136
  7. Le, T. T., Austin., S. A. Lim, S., Buswell, R. A., Gibb, A. G. F., and Thorpe, T. (2012), Mix design and fresh properties for high-performance printing concrete, Materials and Structures, 45(8), 1221-1232. https://doi.org/10.1617/s11527-012-9828-z
  8. Seo, J. S., Lee, B. C., and Kin, Y. Y. (2019), The Effects of Void Ratio on Extrudability and Buildability of Cement-based Composites Produced by 3D Printers, Journal of the Korea Institute for Structural Maintenance and Inspection, 23(7), 104-112 https://doi.org/10.11112/JKSMI.2019.23.7.104
  9. Won, H. J. 2021, Strength characteristics of 3D printed concrete according to the stacking direction, Journal of the Korea Academia-Industrial cooperation Society, 22(2), 632-637 https://doi.org/10.5762/KAIS.2021.22.2.632
  10. KCI-CT115, (2021), Standard Method of Making Compressive Strength Specimens of Underwater Additive Layering Concrete, Standards of the Korean Concrete Society