DOI QR코드

DOI QR Code

Compressive strength behaviour of low-strength hollow concrete block masonry prisms

  • 투고 : 2021.02.09
  • 심사 : 2021.10.06
  • 발행 : 2021.12.25

초록

The present study aims to understand the behaviour of low-strength masonry prisms constructed with locally-produced low-strength hollow concrete blocks. Compression tests were conducted on masonry prisms constructed with three different mortar grades of cement-sand ratios of 1:3, 1:4.5 and 1:6 representing strong, moderately strong and weak mortar. Stress-strain curves were generated from the test results for the masonry prisms. The hollow concrete masonry units employed in this study are some of the weakest as compared to other masonry units employed by other researchers. The compressive strengths for masonry prisms with mortar grades 1:3, 1:4.5 and 1:6 are 2.21 MPa, 2.19 MPa and 2.25 MPa respectively. The results indicate that the masonry compressive strength of such low-strength hollow concrete block masonry prisms is not influenced by the mortar strength. Simple relationships to estimate the modulus of elasticity and compressive strength of masonry prisms is also proposed.

키워드

과제정보

Authors are thankful to Mr. Rahkupar Wanshnong, Technician, Department of Civil Engineering, NIT Meghalaya for his enormously help during casting and testing of the specimens.

참고문헌

  1. Akinwumi, I.I., Domo-Spiff, A.H. and Salami, A. (2019), "Marine plastic pollution and affordable housing challenge: Shredded waste plastic stabilized soil for producing compressed earth bricks", Case Stud. Constr. Mater., 11, e00241. https://doi.org/10.1016/j.cscm.2019.e00241.
  2. ASTM C 109/C 109M (2007), Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens), ASTM International, USA.
  3. ASTM C 1314 (2007), Standard Test Method for Compressive Strength of Masonry Prisms, ASTM International, USA.
  4. Basha, S.H. and Kaushik, H.B. (2015), "Evaluation of nonlinear material properties of fly ash brick masonry under compression and shear", J. Mater. Civil Eng., 27(8), 04014227. https://doi.org/10.1061/(asce)mt.1943-5533.0001188.
  5. Castro, I.G., Laursen, P.T., Jansen, D.C. and Qu, B. (2014), "Performance of interlocking compressed earth block infill in confined masonry construction", 10th U.S. National Conference on Earthquake Engineering, Anchorage, AL, USA.
  6. Costigan, A., Pavia, S. and Kinnane, O. (2015), "An experimental evaluation of prediction models for the mechanical behavior of unreinforced, lime-mortar masonry under compression", J. Build. Eng., 4, 283-294. https://doi.org/10.1016/j.jobe.2015.10.001.
  7. da Porto, F., Mosele, F. and Modena, C. (2011), "In-plane cyclic behaviour of a new reinforced masonry system: Experimental results", Eng. Struct., 33(9), 2584-2596. https://doi.org/10.1016/j.engstruct.2011.05.003.
  8. EN 1996-1-1 (2005), Design of Masonry Structures-Part 1-1: General Rules for Reinforced and Unreinforced Masonry Structures, European Committee for Standardization, Brussels.
  9. Ferretti, D. (2020), "Dimensional analysis and calibration of a power model for compressive strength of solid-clay-brick masonry", Eng. Struct., 205, 110064. https://doi.org/10.1016/j.engstruct.2019.110064.
  10. Ferretti, D., Michelini, E. and Rosati, G. (2015), "Mechanical characterization of autoclaved aerated concrete masonry subjected to in-plane loading: Experimental investigation and FE modeling", Constr. Build. Mater., 98, 353-365. https://doi.org/10.1016/j.conbuildmat.2015.08.121.
  11. Gumaste, K.S., Rao, K.S.N., Reddy, B.V.V. and Jagadish, K.S. (2007), "Strength and elasticity of brick masonry prisms and wallettes under compression", Mater. Struct., 40, 241-253. https://doi.org/10.1617/s11527-006-9141-9.
  12. Huang, L., Liao, L., Yan, L. and Yi, H. (2014), "Compressive strength of double H concrete block masonry prisms", J. Mater. Civil Eng., 26(8), 06014019. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001084.
  13. IS 1905 (1987), Code of Practice for Structural Use of Unreinforced Masonry, Bureau of Indian Standards, New Delhi.
  14. Jasinski, R., Drobiec, L. and Piekarczyk, A. (2016), "Mechanical properties of masonry walls made of calcium silicate materials made in Poland. Part 1. Masonry properties and compressive strength", Procedia Eng., 161, 904-910. https://doi.org/10.1016/j.proeng.2016.08.755.
  15. Kaushik, H.B., Rai, D.C. and Jain, S.K. (2007), "Stress-strain characteristics of clay brick masonry under uniaxial compression", J. Mater. Civil Eng., 19(9), 728-739. https://doi.org/10.1061/(ASCE)0899-1561(2007)19:9(728).
  16. Khalaf, F.M. (1996), "Factors influencing compressive strength of concrete masonry prisms", Mag. Concrete Res., 48(175), 95-101. https://doi.org/10.1680/macr.1996.48.175.95.
  17. Koksal, H.O., Karakoc, C. and Yildirim, H. (2005), "Compression behavior and failure mechanisms of concrete masonry prisms", J. Mater. Civil Eng., 17(1), 107-115. https://doi.org/10.1061/(ASCE)0899-1561(2005)17:1(107).
  18. Kumar, S. (2002), "A perspective study on fly ash-lime-gypsum bricks and hollow blocks for low cost housing development", Constr. Build. Mater., 16(8), 519-525. https://doi.org/10.1016/S0950-0618(02)00034-X.
  19. Masonry Standards Joint Committee (2013), Specification for Masonry Structures.
  20. Mohamad, G., Fonseca, F.S., Vermeltfoort, A.T., Martens, D.R.W. and Lourenco, P.B. (2017), "Strength, behavior, and failure mode of hollow concrete masonry constructed with mortars of different strengths", Constr. Build. Mater., 134, 489-496. https://doi.org/10.1016/j.conbuildmat.2016.12.112.
  21. NZS 4230 (2004), Design of Reinforced Concrete Masonry Structures, Standards Association of New Zealand, Wellington, New Zealand.
  22. Quiroz, L.G., Maruyama, Y. and Zavala, C. (2014), "Cyclic behavior of Peruvian confined masonry walls and calibration of numerical model using genetic algorithms", Eng. Struct., 75, 561-576. https://doi.org/10.1016/j.engstruct.2014.06.035.
  23. Sajanthan, K., Balagasan, B. and Sathiparan, N. (2019), "Prediction of compressive strength of stabilized earth block masonry", Adv. Civil Eng., 2019, Article ID 2072430. https://doi.org/10.1155/2019/2072430.
  24. Sarhat, S.R. and Sherwood, E.G. (2014), "The prediction of compressive strength of ungrouted hollow concrete block masonry", Constr. Build. Mater., 58, 111-121. https://doi.org/10.1016/j.conbuildmat.2014.01.025.
  25. Singh, S.B. and Munjal, P. (2016), "Bond strength and compressive stress-strain characteristics of brick masonry", J. Build. Eng., 9, 10-16. https://doi.org/10.1016/j.jobe.2016.11.006.
  26. Syiemiong, H. and Marthong, C. (2019), "Effect of moisture on the compressive strength of low-strength hollow concrete blocks", Comput. Concrete, 23(4), 267-272. https://doi.org/10.12989/cac.2019.23.4.267.
  27. Thaickavil, N.N. and Thomas, J. (2018), "Behaviour and strength assessment of masonry prisms", Case Stud. Constr. Mater., 8, 23-38. https://doi.org/10.1016/j.cscm.2017.12.007.
  28. Thamboo, J.A. and Dhanasekar, M. (2016), "A comparative study of the compression behaviour of thin layer mortared and conventional masonry", Brick and Block Masonry: Trends, Innovations and Challenges-Proceedings of the 16th International Brick and Block Masonry Conference, IBMAC 2016, 1929-1938.
  29. Tomar, A., Paul, D.K. and Agarwal, P. (2017), "Compression and cyclic shear behavior of lime mortar brick masonry", J. Earthq. Tsunami, 12(1), 1750015. https://doi.org/10.1142/S1793431117500154.
  30. Tomazevic, M. and Gams, M. (2012), "Shaking table study and modelling of seismic behaviour of confined AAC masonry buildings", Bull. Earthq. Eng., 10, 863-893. https://doi.org/10.1007/s10518-011-9331-x.
  31. Turkel, S. and Aksin, E. (2012), "A comparative study on the use of fly ash and phosphogypsum in the brick production", Sadhana-Academy Proc. Eng. Sci., 37(5), 595-607. https://doi.org/10.1007/s12046-012-0099-8.
  32. Wang, L., Sun, H., Sun, Z. and Ma, E. (2016), "New technology and application of brick making with coal fly ash", J. Mater. Cycl. Waste Manage., 18(4), 763-770. https://doi.org/10.1007/s10163-015-0368-9.
  33. Wu, F., Li, G., Li, H.N. and Jia, J.Q. (2013), "Strength and stress-strain characteristics of traditional adobe block and masonry", Mater. Struct., 46(9), 1449-1457. https://doi.org/10.1617/s11527-012-9987-y.
  34. Yang, K.H., Lee, Y. and Hwang, Y.H. (2019), "A stress-strain model for brick prism under uniaxial compression", Adv. Civil Eng., 2019, Article ID 7682575. https://doi.org/10.1155/2019/7682575.
  35. Yu, H., Zheng, L., Yang, J. and Yang, L. (2015), "Stabilised compressed earth bricks made with coastal solonchak", Constr. Build. Mater., 77, 409-418. https://doi.org/10.1016/j.conbuildmat.2014.12.069.
  36. Zhou, Q., Wang, F., Zhu, F. and Yang, X. (2017), "Stress-strain model for hollow concrete block masonry under uniaxial compression", Mater. Struct., 50(2), 106. https://doi.org/10.1617/s11527-016-0975-5.
  37. Zhou, X., Song, J., Jiang, X. and Xu, D. (2014), "Experimental study on compressive mechanical performance of fly-ash thermal insulation hollow block masonry", Appl. Mech. Mater., 488-489, 643-646. https://doi.org/10.4028/www.scientific.net/AMM.488-489.643.