DOI QR코드

DOI QR Code

The use of river sand for fine aggregate in UHPC and the effect of its particle size

  • Kang, Su-Tae (Department of Civil Engineering, Daegu University)
  • 투고 : 2020.07.28
  • 심사 : 2020.10.16
  • 발행 : 2020.11.25

초록

For the purpose of improving the properties of UHPC as well as the economic efficiency in production of the material, Availability of river sands as fine aggregate instead of micro silica sand were investigated. Four different sizes of river sands were considered. Using river sand instead of micro silica sand increased the flowability, and decreased the yield stress and plastic viscosity in rheological properties, and the effect was higher with larger particle size of river sand. It was demonstrated by analyses based on the packing density. In the results of compressive strength and elastic modulus, even though river sand was not as good as micro silica sand, it could provide high strength of over 170 MPa and elastic modulus greater than 40 GPa. The difference in compressive strength depending on the size of river sand was explained with the concept of maximum paste thickness based on the packing density of aggregate. The flexural performance with river sand also presented relatively lower resistance than micro silica sand, and the reduction was greater with larger particle size of river sand. The flexural performance was proven to be also influenced by the difference in the fiber orientation distribution due to the size of river sand.

키워드

과제정보

This research was supported by the Daegu University Research Grant (No. 20190490).

참고문헌

  1. Abbas, S., Nehdi, M.L. and Saleem, M.A. (2016), "Ultra-high performance concrete: mechanical performance, durability, sustainability and implementation challenges", Int. J. Concrete Struct. Mater., 10, 271-295. https://doi.org/10.1007/s40069-016-0157-4.
  2. Ahman, S., Hakeem, I. and Maslehuddin, M. (2014), "Development of UHPC mixtures utilizing natural and industrial waste materials as partial replacements of silica fume and sand", Sci. World J., 2014, 713531. https://doi.org/10.1155/2014/713531.
  3. ASTM C1437-07 (2007), Standard Test Method for Flow of Hydraulic Cement Mortar.
  4. Bentz, D.P., Ferraris, C.F. and Galler, M.A. (2012), "Influence of particle size distribution on yield stress and viscosity of cement-fly ash paste", Cement Concrete Res., 42(2), 404-409. https://doi.org/10.1016/j.cemconres.2011.11.006.
  5. Bonneau, O., Lachemi, M. and Dallaire, E., Dugat, J. and Aitcin, P.C. (1997), "Mechanical properties and durability of two industrial reactive powder concretes", ACI Mater. J., 94(4), 286-290. https://doi.org/10.14359/310.
  6. De Larrard, F. (1989), "Ultrafine particles for the making of very high-strength concretes", Cement Concrete Res., 19, 161-172. https://doi.org/10.1016/0008-8846(89)90079-3.
  7. De Larrard, F. and Sedran, T. (1994), "Optimization of ultra-high-performance concrete by the use of a packing model", Cement Concrete Res., 24(6), 997-1009. https://doi.org/10.1016/0008-8846(94)90022-1.
  8. De Larrard, F. and Sedran, T. (2002), "Mixture-proportioning of high-performance concrete", Cement Concrete Res., 32, 1699-1704. https://doi.org/10.1016/S0008-8846(02)00861-X.
  9. De Larrard, F. and Tondat, P. (1993), "Sur la contribution de la topologie du squelette granulaire a la resistance en compression du beton", Mater. Struct., 26, 505-516. https://doi.org/10.1007/BF02472861.
  10. Dils, J., Boel, V. and De Schutter, G. (2013), "Influence of cement type and mixing pressure on air content, rheology and mechanical properties of UHPC", Constr. Build. Mater., 41, 455-463. https://doi.org/10.1016/j.conbuildmat.2012.12.050.
  11. Ferrara, L., di Prisco, M. and Lamperti, M.G.L. (2010), "Identification of the stress-crack opening behavior of HPFRCC: The role of flow-induced fiber orientation", Proceedings of FraMCoS-7, 3, Jeju, Korea.
  12. Ferraris, C.F. and De Larrard, F. (1998), "Testing and modelling of fresh concrete technology", NISTIR 6094, National Institute of Standards and Technology.
  13. Graybeal, B. and Davis, M. (2008), "Cylinder or cube: Strength testing of 80 to 200 MPa (116 to 29 ksi) ultra-high-performance-fiber-reinforced concrete", ACI Mater. J., 105, 603-609. https://doi.org/10.14359/20202.
  14. Graybeal, B. and Tanesi, J. (2007), "Durability of an ultrahigh-performance concrete", J. Mater. Civil Eng., 19(10), 848-854. https://doi.org/10.1061/(ASCE)0899-1561(2007)19:10(848).
  15. Hoornahad, H. and Koenders, E.A.B. (2013), "Effect of the mix composition on rheological Behavior of a fresh granular-cement paste material", Proceedings of the 7th RILEM International Conference on Self-Compacting Concrete and of the 1st RILEM International Conference on Rheology and Processing of Construction Materials, Paris, France.
  16. Huang, H., Gao, X., Li, L. and Wang, H. (2018), "Improvement effect of steel fiber orientation control on mechanical performance of UHPC", Constr. Build. Mater., 188, 709-721. https://doi.org/10.1016/j.conbuildmat.2018.08.146.
  17. Justnes, H. and Vikan, H. (2005), "Viscosity of cement slurries as a function of solids content", Ann. Trans. Nordic Rheol. Soc., 13, 75-82.
  18. Kang, S.T., Choi, J.I., Koh, K.T., Lee, K.S. and Lee, B.Y. (2016), "Hybrid effects of steel fiber and microfiber on the tensile behavior of ultra-high performance concrete", Compos. Struct., 145, 37-42. https://doi.org/10.1016/j.compstruct.2016.02.075.
  19. Kang, S.T. and Kim, J.K. (2010), "The relation between fiber orientation and tensile behavior in an ultra high performance fiber reinforced cementitious composites (UHPFRCC)", Cement Concrete Res., 41, 1001-1014. https://doi.org/10.1016/j.cemconres.2011.05.009.
  20. Kang, S.T., Lee, Y., Park, Y.D. and Kim, J.K. (2010), "Tensile fracture properties of an ultra high performance fiber reinforced concrete (UHPFRC) with steel fiber", Compos. Struct., 92(1), 61-71. https://doi.org/10.1016/j.compstruct.2009.06.012.
  21. Kobayashi, K. (1981), Fiber Reinforced Concrete, Ohmsha, Tokyo, Japan.
  22. Kriegar, I.M. and Dougherty, T.J. (1959), "A mechanism for non-Newtonian flow in suspensions of rigid spheres", J. Rheol., 3, 137-152. https://doi.org/10.1122/1.548848.
  23. Lee, B.Y., Kim, J.K. and Kim, Y.Y. (2009), "Quantitative evaluation technique of polyvinyl alcohol (PVA) fiber dispersion in engineered cementitious composites", Cement Concrete Compos., 31(6), 408-417. https://doi.org/10.1016/j.cemconcomp.2009.04.002.
  24. Li, Y., Tan, K.H. and Yang, E.H. (2018), "Influence of aggregate size and inclusion of polypropylene and steel fibers on the hot permeability of ultra-high performance concrete (UHPC) at elevated temperature", Constr. Build. Mater., 169, 629-637. https://doi.org/10.1016/j.conbuildmat.2018.01.105
  25. Markovic, I. (2006), "High-performance hybrid-fiber concrete-development and utilization", Ph.D. Dissertation, Delft University of Technology, Netherland.
  26. Mooney, M. (1951), "The viscosity of concentrated suspensions of spherical particles", J. Colloid Sci., 6(2), 162-170. https://doi.org/10.1016/0095-8522(51)90036-0.
  27. Mosaberpanah, M.A. and Eren, O. (2017), "Effect of quartz powder, quartz sand and water curing regimes on mechanical properties on UHPC using response surface modelling", Adv. Concrete Constr., 5(5), 481-492. https://doi.org/10.12989/acc.2017.5.5.481.
  28. Nuaklong, R., Chittaurak, J., Jongvivatsakul, P., Pansuk, W., Lenwari, A. and Likitlersuang, S. (2020), "Effect of hybrid polypropylene-steel fibres on strength characteristics of UHPFRC", Adv. Concrete Constr., 10(1), 1-11, https://doi.org/10.12989/acc.2020.10.1.001.
  29. Qi, J., Wang, J. and Feng, Y. (2019), "Shear performance of an innovative UHPFRC deck of composite bridge with coarse aggregate", Adv. Concrete Constr., 7(4), 219-229. https://doi.org/10.12989/acc.2019.7.4.219.
  30. Richard, P. and Cheyrezy, M. (1994), "Reactive powder concretes with high ductility and 200-800 Mpa compressive strength", ACI Mater. J., 144(3), 507-518. https://doi.org/10.14359/4536.
  31. Richard, P. and Cheyrezy, M. (1995), "Composition of reactive powder concrete", Cement Concrete Res., 25(7), 1501-1511. https://doi.org/10.1016/0008-8846(95)00144-2.
  32. Romualdi, J.P. and Mandel, J.A. (1964), "Tensile strength of concrete affected by uniformly distributed and closely spaced short lengths of wire reinforcement", J. Am. Concrete Inst., 61, 657-672. https://doi.org/ 10.14359/7801.
  33. Sharma, R. and Bansal, P.P. (2019), "Efficacy of supplementary cementitious material and hybrid fiber to develop the ultra high performance hybrid fiber reinforced concrete", Adv. Concrete Constr., 8(1), 21-31. https://doi.org/10.12989/acc.2019.8.1.021.
  34. Soroushian, P. and Lee, C.D. (1990), "Distribution and orientation of fibers in steel fiber reinforced concrete", ACI Mater. J., 87, 433-439. https://doi.org/10.14359/1803.
  35. Stahli, P., Custer, R. and van Mier, J.G.M. (2008), "On flow properties, fibre distribution, fibre orientation and flexural behavior of FRC", Mater. Struct., 41, 189-196. https://doi.org/10.1617/s11527-007-9229-x.
  36. Stovall, T., De Larrard, F. and Buil, M. (1986), "Linear packing density model of grain mixtures", Powder Technol., 48(1), 1-12. https://doi.org/10.1016/0032-5910(86)80058-4.
  37. Struble, L. and Sun, G.K. (1995), "Viscosity of portland cement paste as a function of concentration", Adv. Cement Bas. Mater., 2, 62-69. https://doi.org/10.1016/1065-7355(95)90026-8.
  38. Teng, J.G., Xiang, Y., Yu, T. and Fang, Z. (2019), "Development and mechanical behaviour of ultra-high-performance seawater sea-sand concrete", Adv. Struct. Eng., 22(4), 1-21. https://doi.org/10.1177/1369433219858291.
  39. Vitek, J.L., Coufal, R. and Citek, D. (2013), "UHPC-Development and testing on structural elements", Procedia Eng., 65, 218-223. https://doi.org/10.1016/j.proeng.2013.09.033.
  40. Walsh, S.D.C. and Saar, M.O. (2008), "Numerical models of stiffness and yield stress growth in crystal-melt suspensions", Earth Planet. Sci. Lett., 267, 32-44. https://doi.org/10.1016/j.epsl.2007.11.028.
  41. Wang, D., Shi, C., Wu, Z., Xiao, J., Huang Z. and Fang, Z. (2015), "A review on ultra high performance concrete: Part II. hydration, microstructure and properties", Constr. Build. Mater., 96, 368-377. https://doi.org/10.1016/j.conbuildmat.2015.08.095.
  42. Wille, K. and Parra-Montesinos, G.J. (2012), "Effect of beam size, casting method, and support conditions on flexural behavior of ultra-high-performance fiber-reinforced concrete", ACI Mater. J., 109, 379-388. https://doi.org/10.14359/51683829.
  43. Wille, K., Tue, N.V. and Parra-Montesinos, G.J. (2014), "Fiber distribution and orientation in UHP-FRC beams and their effect on backward analysis", Mater. Struct., 47, 1825-1838. https://doi.org/10.1617/s11527-013-0153-y.
  44. Yoo, D.Y. and Banthia, N. (2016), "Mechanical properties of ultra-high-performance fiber-reinforced concrete: A review", Cement Concrete Compos., 73, 267-280. https://doi.org/10.1016/j.cemconcomp.2016.08.001.
  45. Yoo, D.Y., Kang, S.T. and Yoon, Y.S. (2014), "Effect of fiber length and placement method on flexural behavior, tension-softening curve, and fiber distribution characteristics of UHPFRC", Constr. Build. Mater., 64, 67-81. https://doi.org/10.1016/j.conbuildmat.2014.04.007.