DOI QR코드

DOI QR Code

Determination of plastic concrete behavior at different strain rates to determine Cowper-Symonds constant for numerical modeling

  • 투고 : 2019.07.20
  • 심사 : 2020.08.07
  • 발행 : 2020.09.25

초록

Strain rate investigations are needed to calibrate strain-rate-dependent material models and numerical codes. An appropriate material model, which considers the rate effects, need to be used for proper numerical modeling. The plastic concrete cut-off wall is a special underground structure that acts as a barrier to stop or reduce the groundwater flow. These structures might be subjected to different dynamic loads, especially earthquake. Deformability of a structure subjected to dynamic loads is a principal issue which need to be undertaken during the design phase of these structures. The characterization of plastic concrete behavior under different strain rates is essential for proper designing of cut-off walls subjected to dynamic loads. The Cowper-Symonds model, as one of the most commonly applied material models, complies well with the behavior of a plastic concretes in low to moderate strain rates and will be useful in explicit dynamics simulations. This paper aims to present the results of an experimental study on mechanical responses of one of the most useful types of plastic concrete and Cowper-Symonds constant determination procedures in a wide range of strain rate from 0.0005 to 107 (1/s). For this purpose, SHPB, uniaxial, and triaxial compression tests were done on plastic concrete samples. Based on the results of quasi-static and dynamic tests, the dynamic increase factors (DIF) of this material in different strain rates and stress state conditions were determined for calibration of the Cowper - Symonds material models.

키워드

과제정보

The authors wish to thank professor Gholamhosein Majzobi of the impact laboratory, Bu Ali Sina University and Farhad Sheykhani of the rock mechanic laboratory, Tarbiat Modares University, for their help in the experiments. The research was financially supported by the Tarbiat Modares University from the Grant Number 9460522003.

참고문헌

  1. Al Salahi, A.A. and Othman, R. (2016), "Constitutive equations of yield stress sensitivity to strain rate of metals: A comparative study", J. Eng., Article ID 3279047, 7. http://dx.doi.org/10.1155/2016/3279047.
  2. ASTM (1989), Test Method for Unconfined Compressive of Cohesive Soils, Annual Book of ASTM Standards, American Society of Testing and Materials, Philadelphia, ASTM D2166.
  3. ASTM (1989), Test Method for Unconsolidated Undrained Compressive Strength of Cohesive Soils in Triaxial Compression, Annual Book of ASTM Standards, American Society of Testing and Materials, Philadelphia, ASTM D2850.
  4. Bischoff, P.H. and Perry, S.H. (1991), "Compressive behavior of concrete at high strain rates", Mater. Struct., 24(144), 425-450. https://doi.org/10.1007/BF02472016.
  5. Brara, A. and Klepaczko, J.R. (2006), "Experimental characterization of concrete in dynamic tension", Mech. Mater., 38(3), 253-267. https://doi.org/10.1016/j.mechmat.2005.06.004.
  6. Chen, X., Liu, Z., Lu. J. and Fan, X. (2018), "Compressive behavior of concrete under high strain rates after freeze-thaw cycles", Comput. Concrete, 21(2), 209-217. http://dx.doi.org/10.12989/cac.2018.21.2.209.
  7. Chen, X., Wu, S., Zhou, J., Chen, Y. and Qin, A. (2013). "Effect of testing method and strain rate on stress-strain behavior of concrete", J. Mater. Civil Eng., 5(11), 1752-1761. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000732.
  8. Cusatis, G. (2011), "Strain-rate effects on concrete behavior", Int. J. Impact Eng., 38(4) 162-170. https://doi.org/10.1016/j.ijimpeng.2010.10.030.
  9. Dharan, C. and Hauser, F. (1970), "Determination of stress-strain characteristics at very high strain rates", Exp. Mech., 10(9), 370-376. https://doi.org/10.1007/BF02320419.
  10. Gad, E.F., Wilson, J.L., Moore, A.J. and Richards, A.B. (2005), "Effects of mine blasting on residential structures", J. Perform. Constr. Facil., 19(3), 222-228. https://doi.org/10.1061/(ASCE)0887-3828(2005)19:3(222).
  11. Grote, D.L., Park1, S.W. and Zhou, M. (2001), "Dynamic behavior of concrete at high strain rates and pressures: I. experimental characterization", Int. J. Impact Eng., 25, 869-886. https://doi.org/10.1016/S0734-743X(01)00020-3.
  12. Guo, Y.B., Gao, G.F., Jing, L. and Shim, V.P.W. (2017), "Response of high-strength concrete to dynamic compressive loading", Int. J. Impact Eng., 108, 114-135. https://doi.org/10.1016/j.ijimpeng.2017.04.015.
  13. He. Z.J. and Ding. M.J. (2019). "The dynamic mechanic's behavior on triaxial compression of the recycled aggregate concrete", IOP Conf. Series, Earth. Environ. Sci., 283, 012020. https://doi.org/10.1088/1755-1315/283/1/012020-1.
  14. ICOLD (1985), Filling Materials for Watertight Cut-off Walls, Bulletin No. 51.
  15. Jones, N. (1989), Structural Impact, Cambridge University Press.
  16. Kai, M.F., Xiao, Y., Shuai, X.L. and Ye, G. (2016), "Compressive behavior of engineered cementitious composites under high strain-rate loading", J. Mater. Civil Eng., https://doi.org/10.1061/(ASCE)MT.1943-5533.0001781.
  17. Kim, D.J., Sirijaroonchai, K., El- Tawil, S. and Naaman, A.E. (2010), "Numerical simulation of the Split Hopkinson Pressure Bar test technique for concrete under compression", Int. J. Impact Eng., 37(2), 141-149. https://doi.org/10.1016/j.ijimpeng.2009.06.012.
  18. Krishnappa, N., Bruneau, M. and Warn, G. (2013), "Weak-axis behavior of wide flange columns subjected to blast", J. Struct. Eng., 140(5), 1-9. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000917.
  19. Li, Y., Qiu, W.C., Ou, Z.C., Duan, Z.P. and Huang, F.L. (2012), "Strain-rate effects on interaction between Mode I matrix crack and inclined elliptic inclusion under dynamic loadings", Struct. Eng. Mech., 44(6), 801-814. http://dx.doi.org/10.12989/sem.2012.44.6.801.
  20. Lindholm, U.S. (1964), "Some experiments with the split Hopkinson pressure bar", J. Mech. Phys. Solid., 12, 317-335. https://doi.org/10.1016/0022-5096(64)90028-6
  21. Mahboubi, A. and Ajorloo, A. (2005), "Experimental study of the mechanical behavior of plastic concrete in triaxial compression", J. Cement Concrete Res., 35(2), 412-419. https://doi.org/10.1016/j.cemconres.2004.09.011.
  22. Marais, S.T., Tait, R.B., Cloete, T.J. and Nurick, G.N. (2004), "Material testing at high strain rate using the split Hopkinson pressure bar", Lat. Am. J. Solid. Struct., 1, 319-339.
  23. Naderi, M. (2005). "Effects of different constituent materials on the properties of plastic concrete", Int. J. Civil Eng., 3(1), 10-19.
  24. Nateghi, R., Goshtasbi, G. and Nejati, H.R. (2020). "Coupled effects of confining pressure and loading rate on the mechanical behavior of plastic concrete", J. Mater. Civil Eng., 32(10), 04020292. https://doi.org/10.1061/(ASCE)MT.1943-5533.0003341.
  25. Ngo, T., Mendis, P., Gupta, A. and Ramsay, J. (2007), "Blast loading and blast effects on structures-an overview", Electron. J. Struct. Eng., 7(S1), 76-91.
  26. Ngo, T., Mohotti, D. and Remennikov, A. (2015), "Numerical simulations of response of tubular steel beams to close-range explosions", J. Consttr. Steel Res., 105, 151-163. https://doi.org/10.1016/j.jcsr.2014.11.007.
  27. Pajak, M. (2011), "Dynamic response of SFRC under different strain rates-an overview of test results", 7th International Conference Analytical Models and New Concepts in Concrete and Masonry Structures, June, Krakow.
  28. Pandey, A.K. (2013), "Flexural ductility of RC beam sections at high strain rates", Comput. Concrete, 12(4), 537-552. http://dx.doi.org/10.12989/cac.2013.12.4.537.
  29. Pashang Pisheh, Y. and Hosseini, M.M. (2012), "Stress-strain behavior of plastic concrete using monotonic triaxial compression test", J. Cent. South Univ., 19, 1125-1131. http://dx.doi.org/10.1007/s11771-012-1118-y.
  30. Riisgaard, B., Ngo, T., Mendis, P., Georgakis, C.T. and Stang, H. (2007), "Dynamic increase factors for high-performance concrete in compression using split Hopkinson pressure bar", Fracture Mechanics of Concrete and Concrete Structures, Italy.
  31. Ritchie, C.B., Gow, M., Packer, J. and Heidarpour, A. (2017), "Influence of elevated strain rate on the mechanical properties of hollow structural sections", Int. J. Prot. Struct., 8(3), 325-351. https://doi.org/10.1177/20414196177215.
  32. Rukhaiyar, S., Sajwan, G. and Samadhiya, N. K. (2017), "Strength behavior of plain cement concrete subjected to true triaxial compression", Department of Civil Engineering, Indian Institute of Technology Roorkee, Roorkee, Uttarakhand, India.
  33. Sakai, Y., Nakatani, M., Takeuchi, A., Omorai, Y. and Kishi, T. (2016). "Mechanical behavior of cement paste and alterations of hydrates under high-pressure triaxial testing", J. Adv. Concrete Technol., 14, 1-12. https://doi.org/10.3151/jact.14.1.
  34. Sfer, D., Carlo, I., Gettu, R. and Etse. G. (2002), "Study of the behavior of concrete under triaxial compression", J. Eng. Mech., 128(20), 156-163. http://dx.doi.org/10.1061/(ASCE)0733-9399(2002)128:2(156).
  35. Sheng, Y., Yu-bin, L. and Yong, C. (2013). "The strain-rate effect of engineering materials and its unified model", Lat. Am. J. Solid. Struct., 10, 833-844. http://dx.doi.org/10.1590/S1679-78252013000400010.
  36. Tay, Y.S. (2009), "Uniaxial compression tests at various loading rates for reactive powder concrete", Theor. Appl. Fract. Mech., 52(1), 14-21. https://doi.org/10.1016/j.tafmec.2009.06.001.
  37. WeerheijmJ, J. and Van Doormaal, J. (2007), "Tensile failure of concrete at high loading rates: New test data on strength and fracture energy from instrumented spalling tests", Int. J. Impact Eng., 34(3), 609-626. https://doi.org/10.1016/j.ijimpeng.2006.01.005.
  38. Yiben, Z., Lingyu, S., Lijun, L., Taikun, W. and Le, S. (2019), "Experimental and numerical investigations on low-velocity impact response of high strength steel/composite hybrid plate", Int. J. Impact Eng., 123, 1-13. https://doi.org/10.1016/j.ijimpeng.2018.08.015.
  39. Yu, S.S., Bin, L.Y. and Yong, C. (2013), "The strain-rate effect of engineering materials and its unified model", Lat. Am. J. Solid. Struct., 10(4), 833-844. http://dx.doi.org/10.1590/S1679-78252013000400010.
  40. Zhang, F., Wu, C. and Zhao, X. (2015), "Numerical modeling of concrete-filled double-skin steel square tubular columns under blast loading", J. Perform. Constr. Facil., 29(5), B4015002. http://dx.doi.org/10.1061/(ASCE)CF.1943-5509.0000749.
  41. Zhang, X.X., Ruiz, G. and Yu, C. (2008). "Experimental study of combined size and strain rate effects on the fracture of reinforced concrete", J. Mater. Civil Eng., 20(8), 544-551. http://dx.doi.org/10.1061/(ASCE)0899-1561(2008)20:8(544).
  42. Zhao, P. and Lok, T.S. (2005), "Adaptation of impactor for the split Hopkinson pressure bar in characterizing concrete at medium strain rate", Struct. Eng. Mech., 19(6), 603-618. http://dx.doi.org/10.12989/sem.2005.19.6.603.