DOI QR코드

DOI QR Code

A Low-elastic MRE Fabrication Process based on the Taguchi Method

다구찌법을 이용한 저탄성 MRE 제조공정 연구

  • Received : 2019.10.25
  • Accepted : 2019.12.16
  • Published : 2020.02.29

Abstract

In this study, a PDMS-based low-elasticity magnetorheological elastomer (MRE) was fabricated and the Taguchi method was used to identify the factors affecting the elastic modulus. The mixing entropy was calculated using optical microscopy to confirm particle dispersion, which was referenced in the process establishment. In the MRE process, four parameters, namely the curing agent, particle type, particle fraction, and applied magnetic field, were divided into three levels. The elastic modulus of the specimen was compared at the off-state and at 0.2 T using compression tests, and the obtained signal to noise ratio indicated that the softness and change in the elastic modulus of the MRE was mainly affected by the curing agent and the particle fraction.

Keywords

References

  1. Sutrisno, J., Purwanto, A., & Mazlan, S. A., “Recent progress on magnetorheological solids: materials, fabrication, testing, and applications,” Advanced engineering materials, Vol. 17, No. 5, pp. 563-597, 2015. https://doi.org/10.1002/adem.201400258
  2. Lokander, M. and Stenberg, B., “Improving the magnetorheological effect in isotropic magnetorheological rubber materials,” Polymer testing, Vol. 22, No. 6, pp. 677-680, 2003. https://doi.org/10.1016/S0142-9418(02)00175-7
  3. Xuan, S., Xu, Y. and Gong, X., “Recent progress on the magnetorheological plastomers,” International Journal of Smart and Nano Materials, Vol. 6, No. 2, pp. 135-148, 2015. https://doi.org/10.1080/19475411.2015.1062437
  4. Behrooz, M., Wang, X. and Gordaninejad, F., "Performance of a new magnetorheological elastomer isolation system," Smart Materials and Structures, Vol. 23, No. 4, 2014.
  5. Ahmad, S. H., and Sahrim Hj., “Magnetic and microwave absorbing properties of magnetite- thermoplastic natural rubber nanocomposites,” Journal of Magnetism and Magnetic Materials, Vol. 322, No. 21, pp. 3401-3409, 2010. https://doi.org/10.1016/j.jmmm.2010.06.036
  6. Kawasetsu, T., Horii, T., Ishihara, H. and Asada, M., "Mexican-hat-like response in a flexible tactile sensor using a magnetorheological elastomer," Sensors, Vol. 18, No. 2, 587, 2018. https://doi.org/10.3390/s18020587
  7. Li, W. H., Liu, B., Kosasih, P.B. and Zhang, X. Z., “A 2-DOF MR actuator joystick for virtual reality applications,” Sensors and Actuators A: Physical, Vol. 137, No. 2, pp. 308-320, 2007. https://doi.org/10.1016/j.sna.2007.03.015
  8. Vatandoost, H., Norouzi, M., Alehashem, S. M S. and Smoukov, S. K., "A novel phenomenological model for dynamic behavior of magnetorheological elastomers in tension-compression mode," Smart Materials and Structures, Vol. 26, No. 6, 065011, 2017 https://doi.org/10.1088/1361-665X/aa6126
  9. Yao, J., Sun, Y. and Liu, Y., "Magnet-induced aligning magnetorheological elastomer based on ultra-soft matrix," Composites Science and Technology, Vol. 162, pp. 170-179, 2018. https://doi.org/10.1016/j.compscitech.2018.04.036
  10. Wang, Z., Volinsky, A. A. and Gallant, N. D., "Crosslinking effect on polydimethylsiloxane elastic modulus measured by custom‐built compression instrument," Journal of Applied Polymer Science, Vol. 131, No. 22, 41050, 2014.
  11. Seo, K. D., Park, J. M., Jeong, H. and Kim, D. S. "An experimental investigation of mixing of carbon nanotube/polymer composite in a batch-type screw mixer," Microsystem technologies, Vol. 20, No. 2, pp. 243-250, 2014. https://doi.org/10.1007/s00542-013-1929-2
  12. Park, J. M., "A chaotic micromixer using obstruction-pairs," Journal of Micromechanics and Microengineering, Vol. 20, No. 1, 2009.
  13. Yang, W. P. and Tarng, Y. S., "Design optimization of cutting parameters for turning operations based on the Taguchi method," Journal of materials processing technology, Vol. 84, No. 1-3, pp. 122-129, 1998. https://doi.org/10.1016/S0924-0136(98)00079-X