DOI QR코드

DOI QR Code

Development and testing of cored moment resisting stub column dampers

  • Hsiao, Po-Chien (Department of Civil and Construction Engineering, National Taiwan University of Science and Technology) ;
  • Lin, Kun-Sian (Department of Civil Engineering, National Chung Hsing University) ;
  • Liao, Wei-Chieh (Department of Civil Engineering, National Chung Hsing University) ;
  • Zhu, Limeng (School of Civil Engineering, Qingdao University of Technology) ;
  • Zhang, Chunwei (School of Civil Engineering, Qingdao University of Technology)
  • 투고 : 2019.04.14
  • 심사 : 2019.11.30
  • 발행 : 2020.01.10

초록

Moment resisting stub columns (MRSCs) have increasingly adopted in special moment-resisting frame (SMF) systems in steel building structures, especially in Asian countries. The MRSCs typically provide a lower deformation capacity compared to shear-panel stub columns, a limited post-yield stiffness, and severe strength degradation as adopting slender webs. A new MRSC design with cored configuration, consisting of a core-segment and two side-segments using different steel grades, has been proposed in the study to improve the demerits mentioned above. Several full-scale components of the cored MRSC were experimentally investigated focusing on the hysteretic performance of plastic hinges at the ends. The effects of the depths of the core-segment and the adopted reduced column section details on the hysteretic behavior of the components were examined. The measured hysteretic responses verified that the cored MRSC enabled to provide early yielding, great ductility and energy dissipation, enhanced post-yield stiffness and limited strength degradation due to local buckling of flanges. A parametric study upon the dimensions of the cored MRSC was then conducted using numerical discrete model validated by the measured responses. Finally, a set of model equations were established based on the results of the parametric analysis to accurately estimate strength backbone curves of the cored MRSCs under increasing-amplitude cyclic loadings.

키워드

과제정보

연구 과제 주관 기관 : Ministry of Science and Technology, R.O.C.

Ministry of Science and Technology, R.O.C. and National Taiwan University of Science and Technology are gratefully acknowledged for financing and supporting the project under the Grants MOST106-2625-M-005-003.

참고문헌

  1. AISC 341-10 (2010), Seismic Provisions for Structural Steel Buildings, American Institute of Steel Construction; Chicago, Illinois, USA.
  2. AISC 360-10 (2010), Specification for Structural Steel Buildings, American Institute of Steel Construction; Chicago, Illinois, USA.
  3. Alfredo, R.S., Manuel, E.S.L., Jose, R.G.C., Eden, B. and Arturo, L.B. (2014), "Seismic response estimation of steel buildings with deep columns and PMRF", Steel Compos. Struct., 17(4), 471-495. http://dx.doi.org/10.12989/scs.2014.17.4.471.
  4. Dehghan, S.M., Najafgholipour, M.A., Ziarati, S.M. and Mehrpour, M.R. (2018), "Experimental and numerical assessment of beam-column connection in steel moment-resisting frames with built-up double-I column", Steel Compos. Struct., 26(3), 315-328. http://dx.doi.org/10.12989/scs.2018.26.3.315.
  5. Deng, K., Pan, P., Li, W. and Xue, Y. (2015), "Development of a buckling restrained shear panel damper", J. Constr. Steel Res., 106, 311-321. https://doi.org/10.1016/j.jcsr.2015.01.004.
  6. Elkady, A. and Lignos, D.G. (2015), "Analytical investigation of the cyclic behavior and plastic hinge formation in deep wideflange steel beam-columns", Bull. Earthq. Eng., 13, 1097-1118. https://doi.org/10.1007/s10518-014-9640-y.
  7. Engelhardt, M.D. and Popov, E.P. (1992), "Experimental performance of long links in eccentrically braced frames", J. Struct.Eng., 118(11), 3067-3088. https://doi.org/10.1061/(ASCE)0733-9445(1992)118:11(3067).
  8. He, L., Kurata, M. and Nakashima, M. (2015), "Condition assessment of steel shear walls with tapered links under various loadings", Earthq. Struct., 9(4), 767-788. https://doi.org/10.12989/eas.2015.9.4.767.
  9. Hsiao, P.C. and Liao, W.C. (2019), "Effects of hysteretic properties of stud-type dampers on seismic performance of steel moment resisting frame buildings", J. Struct.Eng.-ASCE, 145(7). https://doi.org/10.1061/(ASCE)ST.1943-541X.0002346.
  10. Jones, S.L., Fry, G.T. and Engelhardt, M.D. (2002), "Experimental evaluation of cyclically loaded reduced beam section moment connections", J. Struct.Eng.-ASCE, 128(4), 441-451. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:4(441).
  11. Kim, J., Kim, M. and Eldin, M.N. (2017), "Optimal distribution of steel plate slit dampers for seismic retrofit of structures", Steel Compos. Struct., 25(4), 473-484. http://dx.doi.org/10.12989/scs.2017.25.4.315.
  12. Lian, M., Zhang, H., Cheng, Q. and Su, M. (2019), "Finite element analysis for the seismic performance of steel frame-tube structures with replaceable shear links", Steel Compos. Struct., 30(4), 365-382. http://dx.doi.org/10.12989/scs.2019.30.4.365.
  13. Lu, L., Xu, Y., Liu, J. and Lim, J.B. (2018), "Cyclic performance and design recommendations of a novel weak-axis reduced beam section connection", Steel Compos. Struct., 27(3), 337-353. http://dx.doi.org/10.12989/scs.2018.27.3.471.
  14. Mazzoni, S., McKenna, F., Scott, M.H. and Fenves, G. (2006), OpenSees command language manual, 264, Pacific Earthquake Engineering Research (PEER) Center.
  15. Nakashima, M. (1995), "Strain-hardening behavior of shear panels made of low-yield steel. I: Test", J. Struct. Eng., 121(12), 1742-1749. https://doi.org/10.1061/(ASCE)0733-9445(1995)121:12(1742).
  16. Richards, P.W. and Uang, C.M. (2005), "Effect of flange widththickness ratio on eccentrically braced frames link cyclic rotation capacity", J. Struct.Eng.-ASCE, 131(10), 1546-1552. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:10(1546).
  17. Shayanfar, M.A., Barkhordari, M.A. and Rezaeian, A.R. (2012), "Experimental study of cyclic behavior of composite vertical shear link in eccentrically braced frames", Steel Compos. Struct., 12(1), 13-29. http://dx.doi.org/10.12989/scs.2012.12.1.13.
  18. Soltani, N., Abedi, K., Poursha, M. and Golabi, H. (2017), "An investigation of seismic parameters of low yield strength steel plate shear walls", Earthq. Struct., 12(6), 713-723. https://doi.org/10.12989/eas.2017.12.5.713.
  19. Tsai, K.C., Wu, S. and Popov, E.P. (1995), "Experimental performance of seismic steel beam-column moment joints", J. Struct. Eng., 121(6), 925-931. https://doi.org/10.1061/(ASCE)0733-9445(1995)121:6(925).
  20. Uang, C.M. and Fan, C.C. (2001), "Cyclic stability criteria for steel moment connections with reduced beam section", J. Struct.Eng.-ASCE, 127(9), 1021-1027. https://doi.org/10.1061/(ASCE)0733-9445(2001)127:9(1021).
  21. Ye, L.P., Lu, X.Z., Ma, Q.L., Cheng, G.Y., Song, S.Y., Miao, Z.W. and Pan P. (2008), "Study on the influence of post-yielding stiffness to the seismic response of building structures", Proceedings of the 14th World Conf. on Earthquake Engineering, China Earthquake Administration Ministry of Construction, Beijing.
  22. Zahrai, S.M. (2015), "Cyclic testing of chevron braced steel frames with IPE shear panels", Steel Compos. Struct., 19(5), 1167-1184. http://dx.doi.org/10.12989/scs.2015.19.5.471.
  23. Zahrai, S.M., Mirghaderi, S.R. and Saleh A. (2017), "Increasing plastic hinge length using two pipes in a proposed web reduced beam section" , Steel Compos. Struct., 23(4), 421-433. http://dx.doi.org/10.12989/scs.2017.23.4.421.