DOI QR코드

DOI QR Code

유한요소법을 이용한 수소저장용기 TYPE 1의 압력과 온도조건에 의한 거동특성 연구

Behavior characteristics of hydrogen storage vessel(TYPE 1) under gas pressure and temperature conditions using FEM

  • 투고 : 2020.11.02
  • 심사 : 2020.12.08
  • 발행 : 2020.12.31

초록

본 논문은 압력과 온도조건에 따라 수소저장용기 TYPE 1에서 발생하는 거동특성을 FEM(Finite Element Method)으로 연구한 것이다. 용기의 구조안전성 평가를 위해 최고압력에서 발생한 VMS(Von Mises stress)을 소재의 YS(Yield Strength)를 비교하였고, 수명예측을 위한 기초데이터로써 PSED(Plastic Strain Energy Density) 결과를 분석하였다. 해석결과에 의하면 최고압력 40 Mpa 이상의 가스압에서 저장용기의 바닥면에 항복강도보다 높은 VMS가 발생하여 수소가스 저장용기의 안전성은 확보되지 않았다고 판단된다. 또한, 온도조건에 의해 발생한 VMS의 결과는 대단히 낮아서 온도에 의한 거동은 영향을 무시할 수 있다. VMS/YS이 1이하가 되는 최고압력은 약 30Mpa으로 계산되어 본 논문의 대상이 되는 수소저장용기는 30 Mpa이하의 가스충전압력으로 관리되어야 함을 알 수 있다.

This paper is a study of the behavior characteristics that occur in the hydrogen storage vessel TYPE 1 according to pressure and temperature conditions by FEM(Finite element method). Von Mises stress (VMS) generated at the highest pressure was compared with Yield strength (YS) of the material for structural safety assessment of the container, and the results of plastic strain energy density (PSED) were analyzed as basic data for life expectancy. According to the analysis results, the safety of the hydrogen gas storage vessel is not ensured due to the occurrence of VMS higher than the yield strength on the bottom of the storage container at a gas pressure of 40 Mpa or higher. In addition, the results of VMS caused by temperature conditions are very low and the behavior by temperature can be ignored. The maximum pressure of VMS/YS below 1 is calculated to be about 30 Mpa, indicating that the hydrogen storage container subject to this paper should be managed with a gas charging pressure of less than 30 Mpa.

키워드

참고문헌

  1. The GVR, worldwide NGV statistics, (2010)
  2. Park J. S., Jeung S. S., and Chung J. H., " Cycling life prediction method considering compressive residual stress on liner for the filament-wound composite cylinders with metal liner", Composites Research, 19(1), 22-28, (2006)
  3. Hu Y. D., HU Z. Z., and CAO S. Z., "Theoretical study on Manson-Coffin equation for physically short cracks and lifetime prediction", SCIENCE CHINA, 1-9, (2011)
  4. Kwak D. H., Roh H. R., Kim J. K., and Cho S. B., "A Study on Fretting Fatigue Life Prediction for Cr-Mo Steel(SCM420)", KSPE, 24(1), 123-130, (2007)
  5. Prashant N. and Abhay U., "Fatigue Analysis of 6300 Liters Pressure Vessel By Using Cyclic Service", IJMTER, 1740-1745, (2014)
  6. Kim C. K. and Cho S. H., "Finite Element Analysis of Stress Behaviour Characteristics in Gas Pressure Vessels", KIGAS, 17(3), 58-64, (2003)
  7. Wee S. U.,, Seok C. S.,, Koo J. M., and Lee J. M., "Prediction of Low-Cycle Fatigue Life of In738LC Using Plastic Strain Energy Density", J. Korean Soc. Precis. Eng., 36(4), 401-406, (2019) https://doi.org/10.7736/kspe.2019.36.4.401
  8. Kim C. K. and Cho S. H., "FE Analysis on the Design Safety of Inner Tank Bottom Plate in Terms of Cryogenic Temperature Loadings", KIGAS, 8(3), 8-15, (2004)
  9. Kim C.K., Cho S. H., Suh H. S., Hong S. H., Lee S.R., Kim Y.G., and Kwon B.G., "On the Leakage Safety Analysis of 9% Nickel Type LNG Storage Tank with Thermal Resistance Effects", KIGAS, 9(1), 1-9, (2005)
  10. N.E. Dowling, Mechanical Behavior of Materials, Second Edition, 257-261, Prentice Hall Inc.
  11. Coffin Jr, L. F., "A Study of the Effects of Cyclic Thermal Stresses on a Ductile Metal," Transactions of the American Society of Mechanical Engineers, 76, 931-950, (1954)
  12. Manson S. S., "Behavior of Materials Under Conditions of Thermal Stresses," NACA Technical Report 1170, 317-350, (1954)
  13. Ellyin, F. and Kujawski, D., "Plastic Strain Energy in Fatigue Failure," Journal of Pressure Vessel Technology, 106(4), 342-347, (1984) https://doi.org/10.1115/1.3264362
  14. Liu, R., Zhang, Z., Zhang, P., and Zhang, Z., "Extremely-LowCycleFatigue Behaviors of CU and CU-AL Alloys: Damage Mechanisms and Life Prediction", ActaMaterialia, 83, 341-356, (2015)
  15. MSC/MARC 2020, user's manual, (2020)
  16. www.matdat.com