Journal of the Korea Academia-Industrial cooperation Society (한국산학기술학회논문지)

The Korea Academia-Industrial cooperation Society (한국산학기술학회)
권호 표지
DOI QR코드

DOI QR Code

Development of Permit Vehicle Classification System for Bridge Evaluation in Korea

허가차량 통행에 대한 교량의 안전성 평가를 위한 허가차량 분류 체계 개발

  • Yu, Sang Seon (Department of Civil & Environment Engineering, Gachon University) ;
  • Kim, Kyunghyun (Department of Civil & Environment Engineering, Gachon University) ;
  • Paik, Inyeol (Department of Civil & Environment Engineering, Gachon University) ;
  • Kim, Ji Hyeon (Smart Advanced Construction Technology Research Center, Gachon University)
  • 유상선 (가천대학교 토목환경공학과) ;
  • 김경현 (가천대학교 토목환경공학과) ;
  • 백인열 (가천대학교 토목환경공학과) ;
  • 김지현 (가천대학교 스마트첨단건설기술연구센터)
  • Received : 2020.11.06
  • Accepted : 2020.12.04
  • Published : 2020.12.31
Download PDF
⟨ Previous Next ⟩

Abstract

This study proposes a bridge evaluation system for indivisible permit vehicles such as hydraulic cranes. The permit loads for the bridge evaluation are divided into three categories: routine permit loads, special permit 1 loads, and special permit 2 loads. Routine permit and special permit 1 vehicles are allowed to cross a bridge with normal traffic. For these two permits, the standard lane model in the Korean Highway Bridge Design Code was adopted to consider normal traffic in the same lane. Special permit 2 vehicles are assumed to cross a bridge without other traffic. Structural analyses of two prestressed-beam bridges and two steel box girder bridges were conducted for the proposed permit loads. The rating factors of the four bridges for all permit loads were calculated as sufficiently large values for the moment and shear force so that crossing the bridges can be permitted. A reliability assessment of the bridges was performed to identify the reliability levels for the permit vehicles. It was confirmed that the reliability level of the minimum required strength obtained by the load-resistance factors yields the target reliability index of the design code for the permit vehicles.

이 연구에서는 분리불가능한 허가차량의 통행에 대한 교량의 안전성 평가 체계를 정립하여 제안하였다. 대상으로 하는 허가차량의 하중효과와 도로교설계기준(한계상태설계법)의 설계차량하중의 계수하중효과를 비교하여, 허가차량의 체계를 일상허가와 두 개의 특별허가로 분류하였다. 일상허가 및 특별허가 1에서는 일반차량과 동시 통행하도록 제안하였으며, 특별허가 2에서는 허가차량이 단독 통행하도록 제안하였다. 허가차량의 전후에 동시 통행하는 일반차량의 연행을 고려하기 위하여 도로교설계기준의 표준차로하중을 이용하여 허가 하중 모형을 제안하였다. 제안된 허가 하중 모형을 적용하여 공용중인 프리스트레스트빔교 및 강박스교의 구조해석을 수행하였으며, 도로교설계기준의 하중·저항계수를 이용하여 허가하중 및 설계차량하중의 내하율 계산을 수행하였다. 교량 거더의 휨 및 전단에 대한 내하율 검토 결과 모든 차량하중의 내하율이 크게 계산되어 통행 가능한 것으로 확인되었다. 허가하중 및 설계차량하중의 휨 및 전단에 대한 교량의 신뢰도해석을 수행하여 신뢰도관점에서 충분한 안전성을 확보하는지 여부를 확인하였다. 도로교설계기준의 하중·저항계수를 이용하여 허가하중에 대한 최소요구강도를 계산하였으며, 최소요구강도의 신뢰도해석을 수행하였다. 최소 요구강도의 신뢰도해석 결과 대부분의 허가차량에 대하여 도로교설계기준의 목표신뢰도지수를 확보하는 것으로 확인되었다.

Keywords

References

  1. American Association of State Highway and Transportation Officials, AASHTO LRFD Bridge Design Specifications, Washington, D.C., 2014.
  2. American Association of State Highway and Transportation Officials, The Manual for Bridge Evaluation, Washington, D.C., 2018.
  3. Canadian Standard Association, Canadian Highway Bridge Design Code (CSA S6:19), Ontario, Canada, 2019.
  4. Standards Australia, Australian Standard - Bridge Design Part 7: Bridge Assessment (AS5100.7:2017), New South Wales, Australia, 2017.
  5. M. Mlynarski, W. G. Wassef, and A. S. Nowak, A Comparison of AASHTP Bridge Load Rating Methods. NCHRP Report 700, Transportation Research Board, Washington, D.C., 2011.
  6. F. Moses, Calibration of Load Factors for LRFR Bridge Evaluation, NCHRP Report 454, Transportation Research Board, Washington, D.C., 2001.
  7. Korea Expressway Corporation, Guidelines for Reliability-Based Bridge Evaluations, Seoul, South Korea, 2013 (in Korean).
  8. Ministry of Land, Infrastructure and Transport, Korean Highway Bridge Design Code (Limit State Design), MOLIT, 2012 (in Korean).
  9. A. S. Nowak, Calibration of LRFD bridge design code, NCHRP Report 368, Transportation Research Board, Washington, D.C., 1999, pp.10.
  10. S. H. Lee, Calibration of the Load-Resistance Factors for the Reliability-based Design of Cable-supported Bridges, Ph. D. thesis, Seoul National University, 2014, pp.113-114. (in Korean).
  11. I. Paik, E. S. Hwang, and S. Shin, "Reliability analysis of concrete bridges designed with material and member resistance factors." Computers and Concrete, Techno-Press, Vol. 6, No. 1, pp. 59-78. February 2009, DOI: http://dx.doi.org/10.12989/cac.2009.6.1.059
  12. D. K. Shin, C. Y. Kim, and I. Paik, "Reliability analysis of composite girder designed by LRFD method for positive flexure." Journal of the Korean Society of Civil Engineers, KSCE, Vol. 26, No. 3A, pp. 539-546, May 2006 (in Korean).
  13. C. Bae, Determination of the Load-Resistance Factors for Reliability-Based Codes by Optimization, Master thesis, Seoul National University, Seoul, South Korea, 2016, pp.26.
  14. H. S. Lee, S. W. Song, and J. H. Kim, "Determination of Load-Resistance Factors for Gravitational Loads-Governed Limit State of Korean Bridge Design Code", KSCE Journal of Civil Engineering, Vol.23, No.8, pp.3451-3463, August 2019. DOI: https://doi.org/10.1007/s12205-019-1245-1
  15. A. Haldar and S. Mahadevan, Probability, Reliability and Statistical Methods in Engineering Design, John Wiley & Sons, Inc., New York, pp. 181-224, 2000.
  16. P. L. Liu and A. Der Kiureghian, "Optimization algorithms for structural reliability" Structural safety, Vol. 9, pp. 161-177, February 1991. DOI: https://doi.org/10.1016/0167-4730(91)90041-7
  17. R. Rackwitz and B. Fiessler, "Structural reliability under combined random load sequences." Comput. Struct., Vol. 9, No. 5, pp. 489-494, 1978. https://doi.org/10.1016/0045-7949(78)90046-9