DOI QR코드

DOI QR Code

Reliable experimental data as a key factor for design of mechanical structures

  • Brnic, Josip (Department of Engineering Mechanics, University of Rijeka, Faculty of Engineering) ;
  • Krscanski, Sanjin (Department of Engineering Mechanics, University of Rijeka, Faculty of Engineering) ;
  • Brcic, Marino (Department of Engineering Mechanics, University of Rijeka, Faculty of Engineering) ;
  • Geng, Lin (School of Material Science and Engineering, Harbin Institute of Technology) ;
  • Niu, Jitai (School of Material Science and Engineering, Harbin Institute of Technology) ;
  • Ding, Biao (College of Material Science and Engineering, Shanghai University)
  • 투고 : 2019.03.09
  • 심사 : 2019.07.05
  • 발행 : 2019.10.25

초록

The experimentally determined mechanical behavior of the material under the prescribed service conditions is the basis of advanced engineering optimum design. To allow experimental data on the behavior of the material considered, uniaxial stress tests were made. The aforementioned tests have enabled the determination of mechanical properties of material at different temperatures, then, the material's resistance to creep at various temperatures and stress levels, and finally, insight into the uniaxial high cyclic fatigue of the material under different applied stresses for prescribed stress ratio. Based on fatigue tests, using modified staircase method, fatigue limit was determined. All these data contributes the reliability of the use of material in mechanical structures. Data representing mechanical properties are shown in the form of engineering stress-strain diagrams; creep behavior is displayed in the form of creep curves while fatigue of the material is presented in the form of S-N (maximum applied stress versus number of the cycles to failure) curve. Material under consideration was 18CrNi8 (1.5920) steel. Ultimate tensile strength and yield strength at room temperature and at temperature of $600^{\circ}C$: [${\sigma}_{m,20/600}=(613/156)MPa$; ${\sigma}_{0.2,20/600}=(458/141)MPa$], as well as endurance (fatigue) limit at room temperature and stress ratio of R = -1 : (${\sigma}_{f,20,R=-1}=285.1MPa$).

키워드

과제정보

연구 과제번호 : Investigation, analysis and modeling the behavior of structural elements stressed at room and high temperatures, Failure analysis of materials in marine environment

연구 과제 주관 기관 : University of Rijeka

참고문헌

  1. Ashby, M.F. (2011), Materials Selection in Mechanical Design, 4th Edition, Butterworth Heinemann, New York, NY, USA.
  2. ASTM (2016), "03.01:2016", Mechanical Testing; Elevated and Low-Temperature Tests; Metallography, ASTM Book of Standards Volume, ASTM, USA.
  3. Boresi, A.P., Schmidt, R.J. and Sidebottom, O.M. (1993), Advanced Mechanics of Materials, (5th Edition), John Wiley and Sons, New York, NY, USA.
  4. Bramfitt, B.L. (1997), "Effects of Composition, Processing and Structure on Properties of Irons and Steels", ASM Handbook, Volume 20, Materials Selection and Design, ASM International, USA.
  5. Brnic, J. (2018), Analysis of Engineering Structures and Material Behavior, (1st Edition), John Wiley & Sons, Chichester, United Kingdom.
  6. Brnic, J., Canadija, M., Turkalj, g., Krscanski, S., Lanc, D., Brcic, M. and Gao, Z. (2016), "Short-time creep, fatigue and mechanical properties of low alloy structural steel", Steel Compos. Struct., 22(4), 875-888. https://doi.org/10.12989/scs.2016.22.4.875.
  7. Brnic, J., Turkalj, G., Niu, J., Canadija, M. and Lanc, D. (2013), "Analysis of experimental data on the behavior of steel S275JRReliability of modern design", Mater. Design, 47, 497-504. https://doi.org/10.1016/j.matdes.2012.12.037.
  8. Brooks, C.R. and Choudhury, A. (2002), Failure Analysis of Engineering Materials, McGraw Hill, New York, NY, USA.
  9. Collins, J.A. (1993), Failure of Materials in Mechanical Design, (2nd Edition), John Wiley & Sons, New York, NY, USA.
  10. Draper, N.R. and Smith, H. (1998), Applied Regression Analysis, Wiley-Interscience Publications, 1993.
  11. Drozdov, A.D. (1996), Finite Elasticity and Viscoelasticity, World Scientific Publishing, New Jersey, NJ, USA.
  12. Findley, W.N., Lai, J.S. and Onaran, K. (1989), Creep and Relaxation of Nonlinear Viscoelastic Materials, Dover Publication, Inc., New York, NY, USA.
  13. Hosseini, S.R.E. (2012), "Simulation of case depth of cementation steels according to Fick's Laws", J. Iron Steel Res., 19(11), 71-78. https://doi.org/10.1016/S1006-706X(13)60023-0.
  14. Hosseini, S.R.E., Khosravi, H., Sohrabi, R., Hosseini, Z., Karimi, E. Z. and Makarem, M. (2013), "Correlation between hardenability curves and microstructure of a cementation steel carburized in the presence of Na2CO3 as an energizer material", ISIJ International, 53(12), 2213-2217. https://doi.org/10.2355/isijinternational.53.2213.
  15. ISO (2012), "Metallic Materials-Fatigue Testing-Statistical Planning and Analysis of Data", 12107:2012, International Organization for Standardization, Geneva, Switzerland.
  16. Jana, S., Ramtekkar, T.R. and Ganguly, A. (2001), "Machinability characteristics of alloy and stainless steel bars", Transactions of the Indian Institute of Metals, 54 (1-2), 49-57.
  17. Kabira, M.J. and Bulpett, R. (2007), "A study of fatigue failure initiation in high cycle high-pressure automotive applications and conventional rotating bending fatigue testing", J. Fatigue, 29(9-11), 1966-1970. https://doi.org/10.1016/j.ijfatigue.2007.03.013.
  18. Kong, Q.C., Li, Y., Liu, G.D., Li, C.J., Tong, H. and Gan, W.M. (2017), "Electrochemical machining for micro holes with high aspect ratio on metal alloys using three-electrode PPS in neutral salt solution", J. Adv. Manufact. Technol., 93 (5-8), 1903-1913. https://doi.org/10.1007/s00170-017-0645-y.
  19. Lu, L., Li, J., Su, C. Yi, Sun, P. Y., Chang, L., Zhou, B. B., He, X, H., Zhou and Yu, C. (2019), "Research on fatigue crack growth behavior of commercial pure titanium base metal and weldment at different temperatures", Theoretical Appl. Fracture Mech., 100, 215-224. https://doi.org/10.1016/j.tafmec.2019.01.017.
  20. Raghavan, V. (2004), Materials Science and Engineering, Prentice-Hall of India, New Delhi, India.
  21. Roberts, R. and Newton, C. (1981), "Interpretive report on smallscale test correlation with $K_{Ic}$ data", Welding Research Council Bullet., 265, 1-16.
  22. Shahraki, M., Sohrabi, M.R., Azizyan, G.R. and Narmashiri, K. (2018), "Experimental and numerical investigation of strengthened deficient steel SHS columns under axial compressive loads", Struct. Eng. Mech., 67(2), 207-217. https://doi.org/10.12989/sem.2018.67.2.207.
  23. Shekhter, A., Kim, S., Carr, D.G., Crocker, A.B.L. and Ringer, S.P. (2002), "Assessment of temper embrittlement in an ex-service 1Cr-1Mo-0.25V power generating rotor by Charpy V-notch testing; $K_{Ic}$ fracture toughness and small punch test", J. Pressure Vessels Piping, 79(8-10), 611-615. https://doi.org/10.1016/S0308-0161(02)00087-X.
  24. Solecki, R.P. and Conant, R. (2003), Advanced Mechanics of Materials, Oxford University Press, New York, NY, USA.
  25. Stephens, R.I., Fatemi, A., Stephens, R.R. and Fuchs, H.O. (2001), Metal Fatigue in Engineering, (2nd Edition), John Wiley & Sons, New York, NY, USA.
  26. Suresh, S. (2003), Fatigue of Materials, (2nd Edition), Cambridge University Press, Cambridge, United Kingdom.
  27. Xu, X.L. and Yu, Z.W. (2015), "Cracking failure of locomotive diesel engine injector nozzles", J. Failure Analysis Prevention, 15(4), 513-520. https://doi.org/10.1007/s11668-015-9962-3.
  28. Zhang, G., Kodur, V., Yao, W., Huang, Q. (2019), "Behavior of composite box bridge girders under localized fire exposure conditions", Struct. Eng. Mech., 69(2), 193-204. https://doi.org/10.12989/sem.2019.69.2.193.

피인용 문헌

  1. Deformation Behavior of C15E + C Steel under Different Uniaxial Stress Tests vol.10, pp.11, 2019, https://doi.org/10.3390/met10111445