DOI QR코드

DOI QR Code

Seismic responses of a free-standing two-story steel moment frame equipped with a cast iron-mortar sliding base

  • Chung, Yu-Lin (Department of Architecture, National Cheng Kung University) ;
  • Kuo, Kuan-Ting (Department of Architecture, National Cheng Kung University) ;
  • Nagae, Takuya (Department of Architecture, Nagoya University) ;
  • Kajiwara, Koichi (Hyogo Earthquake Engineering Research Center, National Research Institute for Earth Science and Disaster Resilience)
  • 투고 : 2019.03.29
  • 심사 : 2019.06.05
  • 발행 : 2019.09.25

초록

An experimental study was conducted to evaluate the dynamic behavior of a free-standing frame equipped with a movable base system using cast iron and mortar as the bearing materials. The preliminary friction test indicated that a graphite layer developed on the interface and exhibited stable friction behavior. The friction coefficient ranged from 0.33 to 0.36 when the applied normal compression stress ranged from 2.6 to 5.2 MPa. The effect of the variation of normal compression stress would be small. Shaking table tests on the free-standing frame showed that rock, slide, and rock-slide responses occurred. The cumulative slide distance reached 381 mm under JMA Kobe wave excitation; however, only a few cyclic slides occurred at the same locations along the moving track. Most surfaces sustained single slides. Similar results can be observed in other shaking conditions. The insufficient cyclic sliding and significant rocking resulted in a few graphite layers on the mortar surfaces. Friction coefficients were generally similar to those obtained in the preliminary friction tests; however, the values fluctuated when the rocking became significant. The collisions due to rocking caused strong horizontal acceleration responses and resulted in high friction coefficient. In addition, the strong horizontal acceleration responses caused by the collisions made the freestanding specimen unable to reduce the input horizontal acceleration notably, even when slippage occurred. Compared with the counterpart fixed-base specimen, the specimen equipped with the iron-mortar base could reduce the horizontal acceleration amplification response and the structural deformation, whereas the vertical acceleration response was doubled due to collisions from rocking.

키워드

참고문헌

  1. Amiri, G.G., Shakouri, A., Veismoradi, S. and Namiranian, P. (2017), "Effect of seismic pounding on buildings isolated by triple friction pendulum bearing", Earthq. Struct., 12(1), 35-45. https://doi.org/10.12989/eas.2017.12.1.035.
  2. Bakhshi, A., Araki, H. and Shimazu, T. (1998), "Evaluation of the performance of a suspension isolation system subjected to strong ground motion", Earthq. Eng. Struct. Dyn., 27(1), 29-47. https://doi.org/10.1002/(SICI)1096-9845(199801)27:1<29.
  3. Campbell, W.E. (1939), "Studies in boundary lubrication", Tran. ASME, 61, 633-641.
  4. Chang, S., Makris, N., Whittaker, A.S. and Thompson, A.C.T. (2002), "Experimental and analytical studies on the performance of hybrid isolation systems", Earthq. Eng. Struct. Dyn., 31(2), 421-443. https://doi.org/10.1002/eqe.117.
  5. Constantinou, M.C., Whittaker, A.S., Kalpakidis, Y., Fenz, D.M. and Warn, G.P. (2007), "Performance of seismic isolation hardware under service and seismic loading", Report No. MCEER-07-0012, Multidisciplinary Center for Earthquake Engineering Research, New York.
  6. Editorial Committee for the Report on the Hanshin-Awaji Earthquake Disaster (1997), Report on the Hanshin-Awaji Earthquake Disaster, building series, Structural damage to steel buildings, Vol. 3, Architectural Institute of Japan, Tokyo, Japan. (in Japanese)
  7. Enokida, R. and Nagae, T. (2017), "Seismic damage reduction of a structural system based on nontraditional sliding interfaces with graphite lubrication", J. Earthq. Eng., 22(4), 666-686. https://doi.org/10.1080/13632469.2016.1264326.
  8. Fakhouri, M.Y. and Igarashi, A. (2013), "Multiple-slider surfaces bearing for seismic retrofitting of frame structures with soft first stories", Earthq. Eng. Struct. Dyn., 42(1), 145-161. https://doi.org/10.1002/eqe.2198.
  9. Hsiao, C.P., Ding, Y.C., Sheu, M.S. and Tsai, K.C. (1999), "Investigation report of the 921 Chi-Chi earthquake: structural damages", Report No. NCREE-99-054, National Center for Research on Earthquake Engineering (NCREE). (in Chinese)
  10. Japan Meteorological Agency, http://www.data/jma.go.jp/svd/eqev/data/kyoshin/jishin/hyogo_nanbu/index.html.
  11. Kajiwara, K., Tosauchi, Y., Sato, E., Fukuyama, K., Inoue, T., Shiohara, H., Kabeyasawa, T., Nagae, T., Fukuyama, H., Kabeyasawa, T. and Mukai, T. (2017), "Three-dimensional shaking table test of a 10-story reinforced concrete building on the E-defense Part 1: Overview and specimen design of the base slip and base fixed tests", 16th World Conference on Earthquake Engineering, Santiago, Chile, January.
  12. McCormick, J., Nagae, T., Ikenaga, M., Zhang, P., Katsuo, M. and Nakashima, M. (2009), "Investigation of the sliding behavior between steel and mortar for seismic applications in structures", Earthq. Eng. Struct. Dyn., 38(12), 1401-1419. https://doi.org/10.1002/eqe.908.
  13. Mokha, A., Constantinou, M., Reinhorn, A. and Zayasm V. (1991), "Experimental study of friction-pendulum isolation system", J. Struct. Eng., 117(4), 1201-1217. https://doi.org/10.1061/(ASCE)0733-9445(1991)117:4(1201).
  14. Mokha, A., Constantinou, M.C. and Reinhorn, A.M. (1990), "Teflon bearings in base isolation. I: Testing", J. Struct. Eng., 116(2), 438-454. https://doi.org/10.1061/(ASCE)0733-9445(1990)116:2(438).
  15. Mostaghel, N. and Khodaverdian, M. (1987), "Dynamics of resilient-friction base isolator (R-FBI)", Earthq. Eng. Struct. Dyn., 15(3), 379-390. https://doi.org/10.1002/eqe.4290150307.
  16. National Center for Research on Earthquake Engineering, (NCREE), https://www.ncree.org/Ncree.aspx?id=4.
  17. Rabbat, B. and Russel, H. (1985), "Friction coefficient of steel on concrete or grout", J. Struct. Eng., 111(3), 505-515. https://doi.org/10.1061/(ASCE)0733-9445(1985)111:3(505).
  18. Sato, E., Tosauchi, Y., Fukuyama, K., Inoue, T., Kajiwara, K., Shiohara, H., Kabeyasawa, T., Nagae, T., Fukuyama, H., Kabeyasawa, T. and Mukai, T. (2017), "Three-dimensional shaking table test of a 10-story reinforced concrete building on the E-defense Part 2: Specimen fabrication and construction, test procedure, and instrumentation program", 16th World Conference on Earthquake Engineering, Santiago, Chile, January.
  19. Tassios, T. and Vintzeleou, E. (1986), "Concrete-to-concrete friction", J. Struct. Eng., 113(4), 832-849. https://doi.org/10.1061/(ASCE)0733-9445(1987)113:4(832).
  20. Tiong, P.L.Y., Adnan, A., Rahman A.B.A. and Mirasa, A.K. (2014), "Seismic base isolation of precast wall system using high damping rubber bearing", Earthq. Struct., 7(6), 1141-1169. https://doi.org/10.12989/eas.2014.7.6.1141.
  21. Tosauchi, Y., Sato, E., Fukuyama, K., Inoue, T., Kajiwara, K., Shiohara, H., Kabeyasawa, T., Nagae, T., Fukuyama, H., Kabeyasawa, T. and Mukai, T. (2017), "Three-dimensional shaking table test of a 10-story reinforced concrete building on the E-defense Part 3: Base slip and vase fixed test results", 16th World Conference on Earthquake Engineering, Santiago, Chile, January.
  22. Tsai, K.C., Hsiao, C.P. and Bruneau, M. (2000), "Overview of building damages in 921 Chi-Chi Earthquake", Earthq. Eng. Eng. Seismol., 2(1), 93-108.
  23. Tsopelas, P., Constatinou, M.C., Kim, Y.S. and Okamoto, S. (1996), "Experimental study of FPS system bridge seismic isolation", Earthq. Eng. Struct. Dyn., 25(1), 65-78. https://doi.org/10.1002/(SICI)1096-9845(199601)25:1<65.
  24. Zayas, V.A., Low, S.S. and Mahin, S.A. (1990), "A simple pendulum technique for achieving seismic isolation", Earthq. Spectra, 6(2), 317-333. https://doi.org/10.1193/1.1585573.