DOI QR코드

DOI QR Code

Efficacy of supplementary cementitious material and hybrid fiber to develop the ultra high performance hybrid fiber reinforced concrete

  • Sharma, Raju (Civil Engineering Department, Thapar Institute of Engineering and Technology) ;
  • Bansal, Prem Pal (Civil Engineering Department, Thapar Institute of Engineering and Technology)
  • 투고 : 2018.09.25
  • 심사 : 2019.04.10
  • 발행 : 2019.08.25

초록

The rich recipe of ultra high performance concrete (UHPC) offers the higher mechanical, durability and dense microstructure property. The variable like cement/sand ratio, amount of supplementary cementitious material, water/binder ratio, amount of fiber etc. alters the UHPC hardened properties to any extent. Therefore, to understand the effects of these variables on the performance of UHPC, inevitably a stage-wise development is required. In the present experimental study, the effect of sand/cement ratio, the addition of finer material (fly ash and quartz powder) and, hybrid fiber on the fresh, compressive and microstructural property of UHPC is evaluated. The experiment is conducted in three phases; the first phase evaluates the flow value and strength attainment of ingredients, the second phase evaluates the efficiency of finer materials (fly ash and quartz powder) to develop the UHPC and the third phase evaluate the effect of hybrid fiber on the flow value and strength of ultra high performance hybrid fiber reinforced concrete (UHP-HFRC). It has been seen that the addition of fly ash improves the flow value and compressive strength of UHPC as compared to quartz powder. Further, the usage of hybrid fiber in fly ash contained matrix decreases the flow value and improves the strength of the UHP-HFRC matrix. The dense interface between matrix and fiber and, a higher amount of calcium silicate hydrate (CSH) in fly ash contained UHP-HFRC is revealed by SEM and XRD respectively. The dense interface (bond between the fiber and the UHPC matrix) and the higher CSH formation are the reason for the improvement in the compressive strength of fly ash based UHP-HFRC. The differential thermal analysis (DTA/TGA) shows the similar type of mass loss pattern, however, the amount of mass loss differs in fly ash and quartz powder contained UHP-HFRC.

키워드

참고문헌

  1. Abbas, S., Soliman, M.A. and Nehdi, L.M. (2015), "Exploring mechanical and durability properties of ultra-high performance concrete incorporating various steel fiber lengths and dosages", Constr. Build. Mater., 75, 429-441. https://doi.org/10.1016/j.conbuildmat.2014.11.017.
  2. Alarcon-Ruiz, L., Gerard, P., Etienne, M. and Alain, E. (2005), "The use of thermal analysis in assessing the effect of temperature on a cement paste", Cement Concrete Res., 35(3), 609-613. https://doi.org/10.1016/J.CEMCONRES.2004.06.015.
  3. ASTM C1856 / C1856M - 17, Standard Practice for Fabricating and Testing Specimens of Ultra-High Performance Concrete, ASTM International, West Conshohocken, PA,
  4. Baert, G., Hoste, S., Schutter, D.G. and Belie, D.N. (2008), "Reactivity of fly ash in cement paste studied by means of thermogravimetry and isothermal calorimetry", J. Therm. Anal. Calorim., 94(2), 485-492. https://doi.org/10.1007/s10973-007-8787-z.
  5. Bellew, G.E.P (1996), "Microstructural investigation of deteriorated Portland cement concretes", Constr. Build. Mater., 10(1), 3-16. https://doi.org/10.1016/0950-0618(95)00066-6.
  6. Deschner, F., Winnefeld, F., Lothenbach, B., Seufert, S., Schwesig, P., Dittrich, S., Goetz-Neunhoeffer, F. and Neubauer, J. (2012), "Hydration of Portland cement with high replacement by siliceous fly ash", Cement Concrete Res., 42(10), 1389-1400. https://doi.org/10.1016/J.CEMCONRES.2012.06.009.
  7. European Committee for Standardization (CEN), EN 196-1 (1995), Methods of Testing Cement-Part 1: Determination of Strength.
  8. Fennis, A.A.M.F. and Walraven, J.C. (2012), "Using particle packing technology for sustainable concrete mixture design", Heron., 57(2), 73-101.
  9. Fraay, A.L.A., Bijen, J.M. and Haan, D.Y.M. (1989), "The reaction of fly ash in concrete a critical examination", Cement Concrete Res., 19(2), 235-246. https://doi.org/10.1016/0008-8846(89)90088-4.
  10. Funk, J.E. and Dinger, D.R. (1994), Predictive Process Control of Crowded Particulate Suspensions, Applied to Ceramic Manufacturing, Kluwer Academic Publishers, Boston, United States.
  11. Ghafari, E., Costa, H., JUlio, E., Portugal, A. and Duraes, L. (2014), "The effect of nanosilica addition on flowability, strength and transport properties of ultra high performance concrete", Mater. Des., 59, 1-9. https://doi.org/10.1016/j.matdes.2014.02.051.
  12. Grunewald, S. (2004), "Performance-based design of self-compacting fibre reinforced concrete", Ph.D. Dissertation, Delft University of Technology.
  13. Johari, M.A.M., Zeyad, A.M., Bunnori, M.N. and Ariffin, K.S. (2012), "Engineering and transport properties of high-strength green concrete containing high volume of ultrafine palm oil fuel ash", Constr. Build. Mater., 30, 281-288. https://doi.org/10.1016/j.conbuildmat.2011.12.007.
  14. Joshi, C.R. and Nagaraj, S.T. (1990), "Generalization of flow behavior of cement -fly - ash pastes and mortars", J. Mater. Civil Eng., 2(3), 128-135. https://doi.org/10.1061/(ASCE)0899-1561(1990)2:3(128)
  15. Kondraivendhan, B. and Bhattacharjee, B. (2015), "Flow behavior and strength for fly ash blended cement paste and mortar", Int. J. Sustain. Built Environ., 4(2), 270-277. https://doi.org/10.1016/J.IJSBE.2015.09.001.
  16. Korpa, R. and Trettin, A. (2008), "Ultra high performance cement based composites with advanced properties containing nanoscale pozzolans", Proc. Second Int. Symp. Ultra High Perform. Concr., Kessel, Germany.
  17. Kwon, S., Nishiwaki, T., Kikuta, T. and Mihashi, H. (2013), "Tensile behavior of ultra high performance hybrid fiber reinforced cement-based composites", VIII International Conference on Fracture Mechanics of Concrete and Concrete Structures FraMCoS-8, 1-6.
  18. Kwon, S., Nishiwaki, T., Kikuta, T. and Mihashi, H. (2014), "Development of Ultra-High-Performance hybrid Fiber-Reinforced Cement-Based composites", ACI Mater. J., 111(3), 309-318.
  19. Lura, P., Trtik, P. and Munch, B. (2011), "Validity of recent approaches for statistical nanoindentation of cement pastes", Cement Concrete Compos., 33(4), 457-465. https://doi.org/10.1016/j.cemconcomp.2011.01.006.
  20. Markovic, I. (2006), "High-performance hybrid-fibre concrete: Development and utilisation". Ph.D. Dissertation, Delft University of Technology.
  21. Mohammed, N.A., Johari, M.A.M., Zeyad, M.A., Tayeh, A.B. and Yusuf, O.M. (2014), "Improving the engineering and fluid transport properties of ultra-high strength concrete utilizing ultrafine palm oil fuel ash", J. Adv. Concr. Technol., 12(4), 127-137. https://doi.org/10.3151/jact.12.127.
  22. Mosaberpanah, A.M and Eren, O. (2013), "Effect of quartz powder, quartz sand and water curing regimes on mechanical properties of UHPC using response surface modelling", Adv. Concrete Constr., 5(5), 481-492. https://doi.org/10.12989/acc.2017.5.5.481.
  23. Nguyen, D.L., Kim, J.D., Ryu, S.G. and Koh, T.K. (2013), "Size effect on flexural behavior of ultra-high-performance hybrid fiber-reinforced concrete", Compos. Part B Eng., 45(1), 1104-1116. https://doi.org/10.1016/j.compositesb.2012.07.012.
  24. Noumowe, A. (1995), "Effet des hautes temperatures (20 $-600^{\circ}C$) sur le beton a hautes performances", PhD Dissertation, Institut National des Sciences Appliquees.
  25. Ollivier, P.J., Maso, C.J. and Bourdette, B. (1995), "Interfacial transition zone in concrete", Adv. Cement Bas. Mater., 2(1), 30-38. https://doi.org/10.1016/1065-7355(95)90037-3.
  26. Prem, P. Bharatkumar, B. and Iyer, R.N. (2012), "Mechanical properties of ultra high performance concrete", World Acad. Sci., 6(8), 676-685.
  27. Park, S.H., Kim, D.J., Ryu, G.S. and Koh, K.T. (2012), "Tensile behavior of ultra high performance hybrid fiber reinforced concrete", Cement Concrete Compos., 34(2), 172-184. https://doi.org/10.1016/j.cemconcomp.2011.09.009.
  28. Rahhal, V. and Talero, R. (2004), "Influence of two different fly ashes on the hydration of portland cements", J. Therm. Anal. Calorim., 78(1), 191-205. https://doi.org/10.1023/B:JTAN.0000042167.46181.17.
  29. Rangaraju, P.R., Kizhakommudom, H, and Li, Z. (2014), "Development of high-strength / high performance concrete / grout mixtures for application in shear keys in precast bridges", Research Report Number, FHWA-SC-13-04a, Glenn Department of Civil Engineering, Clemson University, Clemson, South Carolina, USA.
  30. Reda, M.M., Shrive, N.G. and Gillott, J.E. (1999), "Microstructural investigation of innovative UHPC", Cement Concrete Res., 29(3), 323-329. https://doi.org/10.1016/S0008-8846(98)00225-7.
  31. Rossi, P., Acker, P. and Malier, Y. (1987), "Effect of steel fibres at two different stages: The material and the structure", Mater. Struct., 20(6), 436-439. https://doi.org/10.1007/BF02472494
  32. Schmidt, M. and Fehling, E. (2005), "Ultra-high-performance concrete: research, development and application in Europe", ACI Spec. Publ., 228, 51-78.
  33. Sorelli, L., Constantinides, G., Ulm, J.F. and Toutlemonde, F. (2008), "The nano-mechanical signature of Ultra High Performance Concrete by statistical nanoindentation techniques", Cement Concrete Res., 38(12), 1447-1456. https://doi.org/10.1016/j.cemconres.2008.09.002.
  34. Staquet, B. and Espion, S. (2004), "Early-age autogenous shrinkage of UHPC incorporating very fine fly ash or metakaolin in replacement of silica Fume", Proceedings of the Int. Symp. Ultra High Perform. Concr., Kassel, Germany, September.
  35. Tuan, V.N., Ye, G., Breugel, V.K., Fraaij, L.A.A. and Dai, D.D. (2011), "The study of using rice husk ash to produce ultra high performance concrete", Constr. Build. Mater., 25(4), 2030-2035. https://doi.org/10.1016/j.conbuildmat.2010.11.046.
  36. Ulm, F.J., Vandamme, M., Jennings, H.M., Vanzo, J., Bentivegna, M., Krakowiak, K.J., Constantinides, G., Bobko, C.P. and Van Vliet, K.J. (2010), "Does microstructure matter for statistical nanoindentation techniques?, Cement Concrete Compos., 32(1), 92-99. https://doi.org/10.1016/j.cemconcomp.2009.08.007.
  37. Yu, R., Spiesz, P. and Brouwers, H.J.H. (2015), "Development of Ultra-High Performance Fibre Reinforced Concrete (UHPFRC): towards an efficient utilization of binders and fibres", Constr. Build. Mater., 79, 273-282. https://doi.org/10.1016/j.conbuildmat.2015.01.050.
  38. Yu, R., Spiesz, P. and Brouwers, H.J.H. (2014c), "Mix design and properties assessment of Ultra-High Performance Fibre Reinforced Concrete (UHPFRC)", Cement Concrete Res. 56, 29-39. https://doi.org/10.1016/j.cemconres.2013.11.002.
  39. Wang, C., Yang, C., Liu, F., Wan, C. and Pu, X. (2012), "Preparation of Ultra-High Performance Concrete with common technology and materials", Cement Concrete Compos., 34(4), 538-544. https://doi.org/10.1016/j.cemconcomp.2011.11.005.
  40. Yang, I.H., Joh, C. and Kim, B.S. (2011), "Flexural strength of ultra high strength concrete beams reinforced with steel fibers", Procedia Eng., 14, 793-796. https://doi.org/10.1016/j.proeng.2011.07.100.
  41. Yu, R., Spiesz, P. and Brouwers, H.J.H. (2014a), "Effect of nano-silica on the hydration and microstructure development of Ultra-High Performance Concrete (UHPC) with a low binder amount", Constr. Build. Mater., 65, 140-150. https://doi.org/10.1016/j.conbuildmat.2014.04.063.
  42. Yu, R., Spiesz, P. and Brouwers, H.J.H. (2015), "Development of an eco-friendly Ultra-High Performance Concrete (UHPC) with efficient cement and mineral admixtures uses", Cement Concrete Compos., 55, 383-394. https://doi.org/10.1016/j.cemconcomp.2014.09.024.
  43. Yu, R., Tang, P., Spiesz, P. and Brouwers, H.J.H. (2014b), "A study of multiple effects of nano-silica and hybrid fibres on the properties of Ultra-High Performance Fibre Reinforced Concrete (UHPFRC) incorporating waste bottom ash (WBA)", Constr. Build. Mater., 60, 98-110. https://doi.org/10.1016/j.conbuildmat.2014.02.059.
  44. Zhang, J., Zhao, Y. and Li, H. (2017), "Experimental Investigation and prediction of compressive strength of ultra-high performance concrete containing supplementary cementitious materials", Adv. Mater. Sci. Eng., 2017, https://doi.org/10.1155/2017/4563164.

피인용 문헌

  1. Comparison of the effect of lithium bentonite and sodium bentonite on the engineering properties of bentonite-cement-sodium silicate grout vol.9, pp.3, 2020, https://doi.org/10.12989/acc.2020.9.3.279
  2. Static behavior of stud shear connectors with initial damage in steel-UHPC composite bridges vol.9, pp.4, 2019, https://doi.org/10.12989/acc.2020.9.4.413
  3. The use of river sand for fine aggregate in UHPC and the effect of its particle size vol.10, pp.5, 2019, https://doi.org/10.12989/acc.2020.10.5.431
  4. Effect of cement as mineral filler on the performance development of emulsified asphalt concrete vol.10, pp.6, 2019, https://doi.org/10.12989/acc.2020.10.6.515
  5. Long-term monitoring of a hybrid SFRC slab on grade using recycled tyre steel fibres vol.10, pp.6, 2019, https://doi.org/10.12989/acc.2020.10.6.547
  6. Development of high performance hybrid fiber reinforced concrete using different fine aggregates vol.11, pp.1, 2019, https://doi.org/10.12989/acc.2021.11.1.019
  7. Improving the flexural toughness behavior of R.C beams using micro/nano silica and steel fibers vol.11, pp.1, 2021, https://doi.org/10.12989/acc.2021.11.1.045
  8. Microstructure and mechanical behavior of cementitious composites with multi-scale additives vol.11, pp.2, 2019, https://doi.org/10.12989/acc.2021.11.2.163
  9. Mix design and early-age mechanical properties of ultra-high performance concrete vol.11, pp.4, 2019, https://doi.org/10.12989/acc.2021.11.4.335
  10. Experimental comparability between steam and normal curing methods on tensile behavior of RPC vol.11, pp.4, 2019, https://doi.org/10.12989/acc.2021.11.4.347