DOI QR코드

DOI QR Code

Effect of fatigue crack propagation on natural frequencies of system in AISI 4140 Steel

  • Bilge, Habibullah (Department of Mechanical Engineering, Abant Izzet Baysal University) ;
  • Doruk, Emre (R&D Department, TOFAS-FIAT) ;
  • Findik, Fehim (Department of Metallurgical and Materials Engineering, Sakarya University of Applied Science) ;
  • Pakdil, Murat (Department of Mechanical Engineering, Abant Izzet Baysal University)
  • 투고 : 2018.05.08
  • 심사 : 2019.06.20
  • 발행 : 2019.08.10

초록

In this study, we investigated the effect of fatigue crack propagation of the beams which have a vital importance in engineering applications, on the natural frequency of the system. Beams which have a wide range of applications, are used as fundamental structural elements in engineering structures. Therefore, early detection of any damages in these structures is of vital importance for the prevention of possible destructive damages. One of the widely used methods of early detection of damages is the vibration analysis of the structure. Hence, it is of vital importance to detect and monitor any changes in the natural frequencies of the structure. From this standpoint, in this study we experimentally investigated the effect of fatigue crack propagation on beams produced from 4140 steel, of the natural frequency of the beam. A crack was opened on the $8{\times}16{\times}500mm$ beam using a 3 mm long and 0.25 mm wide wire erosion. The beam, then, underwent 3 point bending tests at 10 Hz with a dynamic fatigue device and its natural frequencies were measured in scheduled intervals and any changes taking place on the natural frequencies of the beam were measured. This data allowed us to identify and measure the crack occurring on the beam subjected to dynamic loading, during the propagation phase. This method produced experimental data. The experimental data showed that the natural frequency of the beam decreased with the propagation of the fatigue crack on the beam.

키워드

참고문헌

  1. Agarwalla, D.K. and Parhi, D.R. (2013), "Effect of crack on modal parameters of a cantilever beam subjected to vibration", Procedia Engineering, 51(1), 665-669. https://doi.org/10.1016/j.proeng.2013.01.094
  2. Ahmad, M.I.M., Arifin, A., Abdullah, S., Jusoh, W.Z.W. and Singh, S.S.K. (2015), "Fatigue crack effect on magnetic flux leakage for A283 grade C steel", Steel Compos. Struct., Int. J., 16(9), 1549-1560. http://dx.doi.org/10.12989/scs.2015.19.6.1549
  3. Aid, A., Semari, Z. and Benguediab, M. (2014), "Cold expansion effect on the fatigue crack growth of Al 6082: numerical investigation", Struct. Eng. Mech., Int. J., 49(2), 225-235. https://doi.org/10.12989/sem.2014.49.2.225
  4. Caddemi, S. and Calio, I. (2009), "Exact closed-form solution for the vibration modes of the euler-bernoulli beam with multiple open cracks", J. Sound Vib., 327(3-5), 473-489. https://doi.org/10.1016/j.jsv.2009.07.008
  5. Daneshmehr, A.R., Nateghi, A. and Inman, D.J. (2013), "Free vibration analysis of cracked composite beams subjected to coupled bending-torsion loads based on a first order shear deformation theory", Appl. Math. Model., 37(24), 10074-10091. https://doi.org/10.1016/j.apm.2013.05.062
  6. Gawande, S.H. and More, R.R. (2016), "Effect of Notch Depth & Location on Modal Natural Frequency of Cantilever Beams", Structures, 8(1), 121-129. https://doi.org/10.1016/j.istruc.2016.09.003
  7. Jassim, Z.A., Ali, N.N., Mustapha, F. and Abdul Jalil, N.A. (2013), "A review on the vibration analysis for a damage occurrence of a cantilever beam", Eng. Fail. Anal., 31(7), 442-461. https://doi.org/10.1016/j.engfailanal.2013.02.016
  8. Kocak, M., Pakdil, M. and Cam, G. (2002), "Fracture behaviour of diffusion bonded titanium alloys with strength mismatch", Sci. Technol. Weld. Join., 7(4), 187-196. https://doi.org/10.1179/136217102225004220
  9. Kumar, A., Murthy R., Gopinath, S. and Iyer, N.R. (2016), "XFEM for fatigue and fracture analysis of cracked stiffened panels", Struct. Eng. Mech., Int. J., 57(1), 65-89. https://doi.org/10.12989/sem.2016.57.1.065
  10. Liu, J., Zhu, W.D., Charalambides, P.G., Shao, Y.M., Xu, Y.F. and Fang, X.M. (2016), "A dynamic model of a cantilever beam with a closed, embedded horizontal crack including local flexibilities at crack tips", J. Sound Vib., 382(11), 274-290. https://doi.org/10.1016/j.jsv.2016.04.036
  11. Lorenzino, P. and Navarro, A. (2015), "The variation of resonance frequency in fatigue tests as a tool for in-situ identification of crack initiation and propagation, and for the determination of cracked areas", Int. J. Fatigue, 70(2), 374-382. https://doi.org/10.1016/j.ijfatigue.2014.08.002
  12. Masserey, B. and Fromme, P. (2017), "Analysis of high frequency guided wave scattering at a fastener hole with a view to fatigue crack detection", Ultrasonics, 76(4), 78-86. https://doi.org/10.1016/j.ultras.2016.12.015
  13. Matsuda, K. and Gotoh, K. (2015), "Numerical simulation of fatigue crack propagation under superimposed stress histories containing different frequency components with several mean stress conditions", Marine Struct., 41(3), 77-95. https://doi.org/10.1016/j.marstruc.2014.12.005
  14. Moezi, S.A., Zakeri, E., Zare, A. and Nedaei, M. (2015), "On the application of modified cuckoo optimization algorithm to the crack detection problem of cantilever euler-bernoulli beam", Comput. Struct., 157(9), 42-50. https://doi.org/10.1016/j.compstruc.2015.05.008
  15. Mousavinasab, S. and Blais, C. (2017), "The influence of different microstructural constituents on the fatigue crack propagation behavior of a nickel PM steel", Int. J. Fatigue, 99(1), 44-54. https://doi.org/10.1016/j.ijfatigue.2017.02.017
  16. Okura, I. and Ishikawa, T. (2002), "Stop-hole conditions to prevent re-initiation of fatigue cracks", Steel Compos. Struct., Int. J., 2(6), 475-488. https://doi.org/10.12989/scs.2002.2.6.475
  17. Orhan, S. (2007), "Analysis of free and forced vibration of a cracked cantilever beam", NDT&E International, 40(6), 443-450. https://doi.org/10.1016/j.ndteint.2007.01.010
  18. Pakdil, M., Cam, G., Kocak, M. and Erim, S. (2011), "Microstructural and mechanical characterization of laser beam welded AA6056 Al-alloy", Mater. Sci. Eng. A, 528(24), 7350-7356. https://doi.org/10.1016/j.msea.2011.06.010
  19. Pei, X., Chen, L., Li, J., Tang, Y. and Chen, K. (2016), "Effect of damage on the vibration modal of a novel three-dimensional and four-directional braided composite T-beam", Compos. Part B: Eng., 86(2), 108-119. https://doi.org/10.1016/j.compositesb.2015.09.022
  20. Rezaee, M. and Hassannejad, R. (2011), "A new approach to free vibration analysis of a beam with breathing crack based on mechanical energy balance method", Acta Mechanica Solida Sinica, 24(2), 185-194. https://doi.org/10.1016/S0894-9166(11)60020-7
  21. Sutar, M.K., Pattnaik, S. and Rana, J. (2015), "Neural based controller for smart detection of crack in cracked cantilever beam", Materials Todays: Proceedings, 2(4-5), 2648-2653. https://doi.org/10.1016/j.matpr.2015.07.225
  22. Tang, L., Qian, C., Wang, Z. and Li, H. (2015), "Experimental study of the strain-strengthening effect on the mixed mode notch-crack fatigue propagation in austenitic stainless steel 06Cr19Ni10", Eng. Fract. Mech., 134(1), 54-60. https://doi.org/10.1016/j.engfracmech.2014.12.003
  23. Tao, C., Fu, Y. and Dai, T. (2017), "Dynamic analysis for cracked fiber-metal laminated beams carrying moving loads and its application for wavelet based crack detection", Compos. Struct., 159(1), 463-470. https://doi.org/10.1016/j.compstruct.2016.09.087
  24. Wang, Y., Shao, Y., Song, S. and Yang, D. (2017), "Static test on failure process of tubular T-joints with initial fatigue crack", Steel Compos. Struct., Int. J., 24(5), 615-633. https://doi.org/10.12989/scs.2017.24.5.615
  25. Xie, Z., Peng, F. and Zhao, T. (2014), "Experimental study on fatigue crack propagation of fiber metal laminates", Steel Compos. Struct., Int. J., 17(2), 145-157. https://doi.org/10.12989/scs.2014.17.2.145
  26. Yao, Y., Wang, J. and Keer, L.M. (2017), "A phase transformation based method to predict fatigue crack nucleation and propagation in metals and alloys", Acta Materialia, 127(4), 244-251. https://doi.org/10.1016/j.actamat.2017.01.039
  27. Zong, L., Shi, G., Wang, Y.Q., Yan, J.B. and Ding, Y. (2017), "Investigation on fatigue behavior of load-carrying fillet welded joints based on mix-mode crack propagation analysis", Arch. Civil Mech. Eng., 17(3), 677-686. https://doi.org/10.1016/j.acme.2017.01.009

피인용 문헌

  1. Free vibration of multi-cracked beams vol.79, pp.4, 2019, https://doi.org/10.12989/sem.2021.79.4.441