References
- Ministry of Trade, Industry and Energy, Development of Applicable Induction Heating Bend and Reliability Verification Technology for Safety Related Piping, 2014 (Class 1,2,3), USA.
- ASME Boiler & Pressure Vessel Committee, ASME B&PV Code, Section III, Division 1, Appendices, Nonmandatory Appendix GG: Minimum Thickness for Pipe Bends, New York, USA, 2015.
- USNRC, Generic Aging Lessons Learned (GALL) Report, USA, 2010. NUREG-1801, Rev.2.
- Z. Keran, I. Novosel, M. Math, Analysis of incremental hot tube bending, in: Proc. of 12th Int. Sci. Conf. Prod. Eng. - CIM2009, Beograd, Serbia, June 17-20, 2009.
- H.W. Lee, J.H. Bae, M.S. Kim, C. Kim, Optimum design of pipe bending based on high-frequency induction heating using dynamic reverse moment, Int. J. Precis. Eng. Manuf. 12 (6) (2011) 1051-1058. https://doi.org/10.1007/s12541-011-0140-6
- Y.S. Lee, J.S. Lim, Y.H. Moon, Mechanical characteristics of low-carbon-steel pipe bent by local induction heating with small bending radii, Mater. Trans. 53 5 (2012) 847-852. https://doi.org/10.2320/matertrans.MF201123
- G.C. Collie, R.J. Higgins, I. Black, Modelling and predicting the deformed geometry of thick-walled pipes subjected to induction bending, J. Mater. Des. Appl. 224 (2010) 177-189.
- J.S. Kim, K.S. Kim, Y.J. Oh, H.Y. Chang, H.B. Park, Investigation of residual stress distributions of induction heating bended austenitic stainless steel (316 series) piping, Trans. KSME A 38 (7) (2014) 809-815. https://doi.org/10.3795/KSME-A.2014.38.7.809
- Sung Il SIM Co, Ltd, Qualification Documents for Bending Manufacturing (SA312 TP304 12" Piping), Republic of Korea, 2013.
- ASME B&PV Code Committee, ASME B&PV Code, Sec.II, Part D, Properties Materials. New York, 2007.
- JRC (Institute for Energy), Protocol for NET Residual Stress Round Robin, EU, 2004.
- V.K. Sikka, Elevated Temperature Ductility of Types 304 and 316 Stainless Steel, USA, 1978. ORNL/TM-6608.
- Lawrence Livermore National Laboratory, High Temperature Properties of Alloys Being Considered for Design of a Concentric Canister Launcher, USA, 1998. UCRL-ID-130924.
- A.K. Steel, Product Data Bulletin, 304/304L Stainless Steel, 304/304L-B-08-01-07. https://www.clevelandmetal.com/wp-content/uploads/sites/640/2015/06/304.304L.Data.Bulletin.pdf.
- Vishay Precision Group, RS-2000 Milling Guide for Residual Stress Measurements, 2011. Document No. 11304, http://www.vishaypg.com/docs/11304/rs200.pdf.
- ASTM International, ASTM E837-13a, Standard Test Method for Determining Residual Stresses by the Hole-Drilling Strain-Gage Method. New York, 2013.
- Dassault Systems, User's Manuals for Simulia Ver.2016, 2016.
- Wikipedia. http://en.wikipedia.org/wiki/Skin_effect.
- P.S. Tech, Analysis Results for Heat Generation Rate by Induction Heating, Republic of Korea, 2013.
- POSCO, Co, Ltd, Continuous Casting, Pohang, 2003.
Cited by
- Joint effect of residual stress and plastic deformation on pulsed eddy current response signals in 304 austenitic stainless steel vol.63, pp.1, 2019, https://doi.org/10.3233/jae-190124