DOI QR코드

DOI QR Code

Investigation on mechanical performance of flat steel plate-lightweight aggregate concrete hollow composite slab

  • Yang, Yong (School of Civil Engineering, Xi'an University of Architecture & Technology) ;
  • Chen, Yang (School of Civil Engineering, Xi'an University of Architecture & Technology) ;
  • Yang, Ye (School of Civil Engineering, Xi'an University of Architecture & Technology) ;
  • Zeng, Susheng (School of Civil Engineering, Xi'an University of Architecture & Technology)
  • 투고 : 2018.03.15
  • 심사 : 2019.04.28
  • 발행 : 2019.05.25

초록

An innovated type of the flat steel plate-lightweight aggregate concrete hollow composite slab was presented in this paper. This kind of the slab is composed of flat steel plate and the lightweight aggregate concrete slab, which were interfaced with a set of perfobond shear connectors (PBL shear connectors) with circular hollow structural sections (CHSS) and the shear stud connectors. Five specimens were tested under static monotonic loading. In the test, the influence of shear span/height ratios and arrangements of CHSS on bending capacity and flexural rigidity of the composite slabs were investigated. Based on the test results, the crack patterns, failure modes, the bending moment-curvature curves as well as the strains of the flat steel plate and the concrete were focused and analyzed. The test results showed that the flat steel plate was fully connected to the lightweight aggregate concrete slab and no obvious slippage was observed between the steel plate and the concrete, and the composite slabs performed well in terms of bending capacity, flexural rigidity and ductility. It was further shown that all of the specimens failed in bending failure mode regardless of the shear span/height ratios and the arrangement of CHSS. Moreover, the plane-section assumption was proved to be valid, and the calculated formulas for predicting the bending capacity and the flexural rigidity of the composite slabs were proposed on the basis of the experimental results.

키워드

과제정보

연구 과제 주관 기관 : National Natural Science Foundation of China, Xi'an University of Architecture and Technology

참고문헌

  1. Ahn, J.H., Lee, C.G., Won, J.H. and Kim, S.H. (2010), "Shear resistance of the perfobond-rib shear connector depending on concrete strength and rib arrangement", J. Constr. Steel Res., 66(10), 1295-1307. https://doi.org/10.1016/j.jcsr.2010.04.008
  2. Al-Darzi, S.Y.K., Chen, A.R. and Liu, Y.Q. (2007), "Finite element simulation and parametric studies of perfobond rib connector", Am. J. Appl. Sci., 4(3), 122-127. https://doi.org/10.3844/ajassp.2007.122.127
  3. Al-Deen, S., Ranzi, G. and Vrcelj, Z. (2011), "Full-scale long-term experiments of simply supported composite beams with solid slabs", J. Constr. Steel Res., 67(3), 308-321. https://doi.org/10.1016/j.jcsr.2010.11.001
  4. Altoubat, S., Ousmane, H. and Barakat, S. (2015), "Effect of fibers and welded-wire reinforcements on the diaphragm behavior of composite deck slabs", Steel Compos. Struct., Int. J., 19(1), 153-171. https://doi.org/10.12989/scs.2015.19.1.153
  5. Ekmekyapar, T., Al-Eliwi, B.J.M., Faraj, R.H., Gogus, M.T. and Al-Shaar, A.A.M. (2017), "Performance of lightweight aggregate and self compacted concrete filled steel tube columns", Steel Compos. Struct., Int. J., 25(3), 299-314.
  6. Ferrer, M., Marimon, F. and Casafont, M. (2018), "An experimental investigation of a new perfect bond technology for composite slabs", Constr. Build. Mater., 166, 618-633. https://doi.org/10.1016/j.conbuildmat.2018.01.104
  7. GB/T 700-2006 (2006), Carbon structure steels; China Planning Press, Beijing, China.
  8. Jiang, J., Main, J.A., Weigand, J.M. and Sadek, F.H. (2018), "Thermal performance of composite slabs with profiled steel decking exposed to fire effects", Fire Safety J., 95, 25-41. https://doi.org/10.1016/j.firesaf.2017.10.003
  9. Johnson, R.P. (2008), Prediction of Shear Resistance of Headed Studs in Troughs of Profiled Sheeting, Blackwell Pub.
  10. Kataoka, M.N., Friedrich, J.T. and Debs, A.L.H.C.E. (2017), "Experimental investigation of longitudinal shear behavior for composite floor slab", Steel Compos. Struct., Int. J., 23(3), 351-362. https://doi.org/10.12989/scs.2017.23.3.351
  11. Leon, R.T., Perea, T, Rassati, G.A. and Lange, J. (2008), "Composite Construction in Steel and Concrete VI", Proceeding of the 2008 Composite Construction in Steel and Concrete Conference, Tabernash, CO, USA, July.
  12. Mirza, O., Kaewunruen, S., Kwok, K. and Griffin, D.W.P. (2016), "Design and modelling of pre-cast steel-concrete composites for resilient railway track slabs", Steel Compos. Struct., Int. J., 22(3), 537-565. https://doi.org/10.12989/scs.2016.22.3.537
  13. Oehlers, D. and Bradford, M. (1995), Composite Steel and Concrete Structural Members: Fundamental Behaviour, Elsevier Science, Pergamon, Oxford, England.
  14. Oguejiofor, E.C. and Hosain, M.U. (1994), "A parametric study of perfobond rib shear connectors", Can. J. Civil Eng., 21(4), 614-625. https://doi.org/10.1139/l94-063
  15. Qiao, W.T., An, Q., Wang, D. and Zhao, M.S. (2016), "Study on mechanical behaviors of cable-supported ribbed beam composite slab structure during construction phase", Steel Compos. Struct., Int. J., 21(1), 177-194. https://doi.org/10.12989/scs.2016.21.1.177
  16. Siekierski, W. (2016), "Analysis of concrete shrinkage along truss bridge with steel-concrete composite deck", Steel Compos. Struct., Int. J., 20(6), 1237-1257. https://doi.org/10.12989/scs.2016.20.6.1237
  17. Su, Q., Yang, G. and Bradford, M.A. (2016), "Bearing capacity of perfobond rib shear connectors in composite girder bridges", J. Bridge Eng., 21(4), 06015009. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000865
  18. Tang, C.W. (2017), "Uniaxial bond stress-slip behavior of reinforcing bars embedded in lightweight aggregate concrete", Struct. Eng. Mech., Int. J., 62(5), 651-661.
  19. Uy, B. and Bradford, M.A. (1996), "Elastic local buckling of steel plates in composite steel-concrete members", Eng. Struct., 18(3), 193-200. https://doi.org/10.1016/0141-0296(95)00143-3
  20. Vianna, J.D.C., Andrade, S.A.L.D., Vellasco, P.C.G.D.S. and Costa-Neves, L.F. (2013), "Experimental study of perfobond shear connectors in composite construction", J. Constr. Steel Res., 81(81), 62-75. https://doi.org/10.1016/j.jcsr.2012.11.002
  21. Wei, X., Xiao, L. and Pei, S. (2015), "Shear behavior of multi-hole perfobond connectors in steel-concrete structure", Struct. Eng. Mech., Int. J., 56(6), 983-1001. https://doi.org/10.12989/sem.2015.56.6.983
  22. Yang, Y., Yu, Y., Zhou, X., Roeder, C.W. and Huo, X. (2016), "Study on mechanical performance of composite beam with innovative composite slabs", Steel Compos. Struct., Int. J., 21(3), 537-551. https://doi.org/10.12989/scs.2016.21.3.537
  23. Zhang, Y.K., Han, Y.X. and Song, Z.Z. (2012), "Experimental Study on Bond Behavior of Profiled Steel Sheet-Lightweight Aggregate Concrete Composite Slab", Adv. Mater. Res., 594-597, 721-724. https://doi.org/10.4028/www.scientific.net/AMR.594-597.721
  24. Zheng, S., Liu, Y., Yoda, T. and Lin, W. (2016), "Shear behavior and analytical model of perfobond connectors", Steel Compos. Struct., Int. J., 20(1), 71-89. https://doi.org/10.12989/scs.2016.20.1.071