DOI QR코드

DOI QR Code

Proposal for Compressive Strength Development Model of Lightweight Aggregate Concrete Using Expanded Bottom Ash and Dredged Soil Granules

바텀애시 및 준설토 기반 인공경량골재 콘크리트의 압축강도 발현 모델 제시

  • 이경호 (경기대학교 일반대학원 건축공학과) ;
  • 양근혁 (경기대학교 건축공학과)
  • Received : 2018.02.19
  • Accepted : 2018.07.19
  • Published : 2018.07.30

Abstract

This study tested 25 lightweight aggregate concrete (LWAC) mixtures using the expanded bottom ash and dredged soil granules to examine the compressive strength gain of such concrete with different ages. The test parameters investigated were water-to-cement ratios and the natural sand content for the replacement of lightweight fine aggregate. The compressive strength gain rate in the basic equation specified in fib model code was experimentally determined in each mixture and then empirically formulated as a function of the water-to-cement ratio and oven-dried density of concrete. When compared with 28-day compressive strength, the tested LWAC mixtures exhibited relatively low gain ratios (0.49~0.82) at an age of 3 days whereas the gain ratios (1.16~1.41) at 91 days were higher than that (1.05~1.15) of the conventional normal-weight concrete. Thus, the fib model equations tend to overestimate the early strength gain of LWAC but underestimate the long-term strength gain. The proposed equations are in good agreement with the measured compressive strength development of LWAC at different ages, indicating that the mean and standard deviation of the normalized root mean square errors determined in each mixture are 0.101 and 0.053, respectively.

Keywords

Acknowledgement

Supported by : 한국연구재단

References

  1. KSC 14 20 12. (2016). Concrete works-Formwork and support, Korea Construction Standard Center.
  2. KSC 14 20 20. (2016). Lightweight aggregate concrete, Korea Construction Standard Center.
  3. KDS 41 10. (2016). Korean building code, Korea Construction Standard Center.
  4. Comite Euro-International du Beton. (2010) fib Model Code for Concrete Structures 2010. Switzerland: International Federation for Structural Concrete (Fib), 402 p.
  5. Lee, J. (2015). The study on the bloating mechnism of the artificial lightweight aggregate. Master's Dissertation, Kyonggi University.
  6. KS L 5201. (2016). Portland cement, Korean Industrial Standards, Chungcheongbuk-do, Korea.
  7. KS F 2527. (2016). Concrete aggregate, Korean Industrial Standards, Chungcheongbuk-do, Korea.
  8. Sim, J. & Yang, K. (2011). Mechanical properties of lightweight aggregate concrete according to the substitution rate of natural sand and maximum aggregate size, Journal of the Korea Concrete Institute, 23(5), 551-558. https://doi.org/10.4334/JKCI.2011.23.5.551
  9. Yang, K. (2013). Mix design of lightweight aggregate concrete and determination of targeted dry density of concrete, Journal of Korea Institute of Building Construction, 13(5), 491-497. https://doi.org/10.5345/JKIBC.2013.13.5.491
  10. Sim, J., & Yang, K. (2010). Air content, workability and bleeding characteristics of fresh lightweight aggregate concrete, Journal of the Korea Concrete Institute, 22(4), 559-566. https://doi.org/10.4334/JKCI.2010.22.4.559
  11. Liu, J., Wang, K., Zhang, Q., Han, F., Sha, J., & Liu, J. (2017). Influence of superplasticizer dosage on the viscosity of cement paste with low water-binder ratio, Concrete and Building Materials, 149(15), 359-366. https://doi.org/10.1016/j.conbuildmat.2017.05.145
  12. Lee, J., Kim, J., & Kim, M. (2015). Fine aggregates size effect on rheological behavior of mortar, Journal of the Korea Academia-Industrial, 16(8), 5636-5645. https://doi.org/10.5762/KAIS.2015.16.8.5636
  13. Neville, A. (2011). Properties of concrete(5 th edition), Harlow, England, Pearson Education Limited