DOI QR코드

DOI QR Code

Influence of stress level on uniaxial ratcheting effect and ratcheting strain rate in austenitic stainless steel Z2CND18.12N

  • Chen, Xiaohui (School of Control Engineering, Northeastern University) ;
  • Chen, Xu (School of Mechanical Engineering & Automation, School of Tianjin University) ;
  • Chen, Haofeng (Department of Mechanical & Aerospace Engineering, University of Strathclyde)
  • 투고 : 2017.07.27
  • 심사 : 2018.02.23
  • 발행 : 2018.04.10

초록

Uniaxial ratcheting behavior of Z2CND18.12N austenitic stainless steel used nuclear power plant piping material was studied. The results indicated that ratcheting strain increased with increasing of stress amplitude under the same mean stress and different stress amplitude, ratcheting strain increased with increasing of mean stress under the same stress amplitude and different mean stress. Based on least square method, a suitable method to arrest ratcheting by loading the materials was proposed, namely determined method of zero ratcheting strain rate. Zero ratcheting strain rate occur under specified mean stress and stress amplitudes. Moreover, three dimensional ratcheting boundary surface graph was established with stress amplitude, mean stress and ratcheting strain rate. This represents a graphical surface zone to study the ratcheting strain rates for various mean stress and stress amplitude combinations. The graph showed the ratcheting behavior under various combinations of mean and amplitude stresses. The graph was also expressed with the help of experimental results of certain sets of mean and stress amplitude conditions. Further, experimentation cost and time can be saved.

키워드

과제정보

연구 과제 주관 기관 : China Postdoctoral Science Foundation, Natural Science Foundation of Hebei Province of China, Central University, Doctoral Scientific Research Foundation of Liaoning Province

참고문헌

  1. Chen, X.H. (2015), "Ratcheting behavior of pressurized Z2CND18.12N stainless steel pipe under different control", modes", Steel Compos. Struct., Int. J., 18(1), 29-50. https://doi.org/10.12989/scs.2015.18.1.029
  2. Facheris, G., Pham, M., Janssens, K.G.F. and Holdsworth, S.R. (2013), "Microscopic analysis of the influence of ratcheting on the evolution of dislocation structures observed in AISI 316L stainless steel during low cycle fatigue", Mater. Sci. Eng. A, 587, 1-11. https://doi.org/10.1016/j.msea.2013.08.041
  3. Kang, G. (2008), "Ratcheting: Recent progress in phenomenon observation constitutive modeling and application", Int. J. Fatigue, 30(8), 1448-1472. https://doi.org/10.1016/j.ijfatigue.2007.10.002
  4. Liang, T. (2014), "A study on the ratcheting effect and ratchetingfatigue behavior of Z2CND18.12N pipe material after thermal aging process", Ph.D. Dissertation; Tianjin University, China.
  5. Ohno, N. (1990), "Recent topics in constitutive modeling of cyclic plasticity and viscoplasticity", Appl. Mech. Rev., 43(11), 283-295. https://doi.org/10.1115/1.3119155
  6. Ohno, N. (1997), "Recent progress in constitutive modeling for ratcheting", Mater. Sci. Res. Int., 3, 1-9.
  7. Pham, M.S., Holdsworth, S.R., Janssens, K.G.F. and Mazza, E. (2013), "Cyclic deformation response of AISI 316L at room temperature: Mechanical behavior, microstructural evolution, physically-based evolutionary constitutive modelling", Int. J. Plast., 47, 143-164. https://doi.org/10.1016/j.ijplas.2013.01.017
  8. Sarkar, A., Okazaki, M., Nagesha, A., Parameswaran, P., Sandhya, R. and Laha, K. (2016), "Generation of Constant Life Diagram under Elevated Temperature Ratcheting of 316LN Stainless Steel", High Temp. Mater. Proc., 35(4), 361-368. https://doi.org/10.1515/htmp-2014-0118
  9. Sarkar, A., Okazaki, M., Nagesha, A., Parameswaran, P., Sandhya R. and Laha, K. (2017), "Mechanisms of failure under low cycle fatigue, high cycle fatigue and creep interactions in combined cycling in a type 316LN stainless steel", Mater. Sci. Eng. A, 683, 24-36. https://doi.org/10.1016/j.msea.2016.11.062
  10. Yu, D.J., Chen, G., Yu, W.-W., Li, D.-M. and Chen, X. (2012), "Visco-plastic constitutive modelling on Ohno-Wang kinematic hardening rule for uniaxial ratcheting behaviour of Z2CND18. 12N steel", Int. J. Plast., 28(1), 88-101. https://doi.org/10.1016/j.ijplas.2011.06.001
  11. Taleb, L. (2013), "On the cyclic behavior of 304L and 316L stainless steels", Key Eng. Mater., 535-536, 201-204. https://doi.org/10.4028/www.scientific.net/KEM.535-536.201