DOI QR코드

DOI QR Code

An Optimal Design Procedure based on the Safety Integrity Level for Safety-related Systems

  • Kim, Sung Kyu (Department of Industrial and Management Engineering, Kyonggi University Graduate School) ;
  • Kim, Yong Soo (Department of Industrial and Management Engineering, Kyonggi University)
  • Received : 2018.03.24
  • Accepted : 2018.06.10
  • Published : 2018.12.31

Abstract

Safety-related systems (SRSs) has widely used in shipbuilding and power generation to prevent fatal accidents and to protect life and property. Thus, SRS performance is a high priority. The safety integrity level (SIL) is the relative performance level of an SRS with regard to its ability to operate reliably in a safe manner. In this article, we proposed an optimal design procedure to achieve the targeted SIL of SRSs. In addition, a more efficient failure mode and effects diagnostic analysis (FMEDA) process and optimization model were developed to improve cost efficiency. Based on previous IEC 61508 diagnostic analyses that revealed unnecessary costs associated with excessive reliability, the new approach consists of two phases: (i) SIL evaluation by FMEDA, and (ii) solution optimization for achieving the target SIL with minimal cost using integer-programming models. The proposed procedure meets the required safety level and minimizes system costs. A case study involving a gas-detection SRS was conducted to demonstrate the effectiveness of the new procedure.

Keywords

References

  1. "Functional safety of electrical/electronic/programmable electronic safety-related systems, 2.0 Edition. IEC 61508," International Electrotechnical Commission (IEC), Geneva, Switzerland, 2010.
  2. S. K. Kim and Y. S. Kim, "An evaluation approach using a HARA and FMEDA for the hardware SIL," Journal of Loss Prevention in the Process Industries, vol. 26, no. 6, pp. 1212-1220, 2013. https://doi.org/10.1016/j.jlp.2013.05.009
  3. W. M. Goble and A. C. Brombacher, "Using a failure modes, effects and diagnostic analysis (FMEDA) to measure diagnostic coverage in programmable electronic systems," Reliability Engineering and System Safety, vol. 66, no. 2, pp. 145-148, 1999. https://doi.org/10.1016/S0951-8320(99)00031-9
  4. M. Catelani, L. Ciani and V. Luongo, "The FMEDA approach to improve the safety assessment according to the IEC61508," Microelectronics Reliability, vol. 50, no. 9-11, pp. 1230-1235, 2010. https://doi.org/10.1016/j.microrel.2010.07.121
  5. I. Yoshimura and Y. Sato, "Safety achieved by the safe failure fraction (SFF) in IEC 61508," IEEE Transactions on Reliability, vol. 57, no. 4, pp. 662-669, 2008. Article (CrossRef Link). https://doi.org/10.1109/TR.2008.928250
  6. R. Pilch, "Extending the Possibilities of Quantitative Determination of SIL-a Procedure Based on IEC 61508 and the Markov Model with Common Cause Failures," Quality and Reliability Engineering International, vol. 33, no. 2, pp. 337-346, 2017. https://doi.org/10.1002/qre.2010
  7. H. Guo and X. Yang, "A simple reliability block diagram method for safety integrity verification," Reliability Engineering and System Safety, vol. 92, no. 9, pp. 1267-1273, 2007. https://doi.org/10.1016/j.ress.2006.08.002
  8. L. Ding, H. Wang, J. Jiang and A. Xu, "SIL verification for SRS with diverse redundancy based on system degradation using reliability block diagram," Reliability Engineering and System Safety, vol. 165, pp. 170-187, 2017. https://doi.org/10.1016/j.ress.2017.03.005
  9. C. H. Hu, X. S. Si and J. B. Yang, "System reliability prediction model based on evidential reasoning algorithm with nonlinear optimization," Expert Systems with Applications, vol. 37, no. 3, pp. 2550-2562, 2010. https://doi.org/10.1016/j.eswa.2009.08.024
  10. M. Demichela, R. Pirani and M. C. Leva, "Human Factor Analysis Embedded in Risk Assessment of Industrial Machines: Effects on the Safety Integrity Level," International Journal of Performability Engineering, vol. 10, no. 5, pp. 487-496, 2014.
  11. E. Piesik, M. Sliwinski and T. Barnert, "Determining and verifying the safety integrity level of the safety instrumented systems with the uncertainty and security aspects," Reliability Engineering and System Safety, vol. 152, pp. 259-272, 2016. https://doi.org/10.1016/j.ress.2016.03.018
  12. "Reliability prediction procedure for electronic equipment," Telcordia Technologies, Inc.,. Telcordia SR-332 Issue 4, Jersey, USA, 2016.
  13. A. Goel and R. J. Graves, "Electronic system reliability: collating prediction models," IEEE Transactions on Device and Materials Reliability, vol. 6, no. 2, pp. 258-265, 2006. https://doi.org/10.1109/TDMR.2006.876570
  14. G. Cassanelli, G. Mura, F. Cesaretti, M. Vanzi and F. Fantini, "Reliability predictions in electronic industrial applications," Microelectronics Reliability, vol. 45 no. 9-11, pp. 1321-1326, 2005. https://doi.org/10.1016/j.microrel.2005.07.014
  15. F. Brissaud, D. Charpentier, M. Fouladirad, A. Barros and and C. Berenguer, "Failure rate evaluation with influencing factors," Journal of Loss Prevention in the Process Industries, vol. 23, no. 2, pp. 1000-1009, 2010.
  16. K. -W. Jang and J. -H. Kim, "A Tabu Search for Multiple Multi-level Redundancy Allocation Problems in Series-Parallel Systems," International Journal of Industrial Engineering: Theory, Applications and Practice, vol. 18, no. 3, pp. 120-129, 2011.
  17. Y. Gheraibia, K. Djafri and H. Krimou, "Ant colony algorithm for automotive safety integrity level allocation," Applied Intelligence, vol. 48, no. 3, pp. 555-569, 2018. https://doi.org/10.1007/s10489-017-1000-6
  18. A. R. Yildiz, "A comparative study of population-based optimization algorithms for turning operations," Information Sciences, vol. 210, pp. 81-88, 2012. https://doi.org/10.1016/j.ins.2012.03.005
  19. A. C. Torres-Echeverria, S. Martorell and H. A. Thompson, "Design optimization of a safety-instrumented system based on RAMS+C addressing IEC 61508 requirements and diverse," Reliability Engineering and System Safety, vol. 94, no. 2, pp. 162-179, 2009. https://doi.org/10.1016/j.ress.2008.02.010
  20. A. C. Torres-Echeverria, S. Martorell and H. A. Thompson, "Modelling and optimization of proof testing policies for safety instrumented systems," Reliability Engineering and System Safety, vol. 94, no. 4, pp. 838-854, 2009. https://doi.org/10.1016/j.ress.2008.09.006
  21. A. C. Torres-Echeverria, S. Martorell and H. A. Thompson, "Multi-objective optimization of design & testing of safety instrumented systems with MooN voting architectures using a genetic algorithm," Reliability Engineering and System Safety, vol. 106, pp. 45-60, 2012. https://doi.org/10.1016/j.ress.2012.03.010
  22. M. Marseguerra, E. Zio, L. Podofillini and D. W. Coit, "Optimal design of reliable network systems in presence of uncertainty," IEEE Transactions on Reliability, vol. 54, no. 2, pp. 243-253, 2005. https://doi.org/10.1109/TR.2005.847279
  23. S. V. Amari, H. Pham and G. Dill, "Optimal design of k-out-of-n:G subsystems subjected to imperfect fault-coverage," IEEE Transactions on Reliability, vol. 53, no. 4, pp. 567-575, 2004. https://doi.org/10.1109/TR.2004.837703
  24. J. Safari, "Multi-objective reliability optimization of series-parallel systems with a choice of redundancy strategies," Reliability Engineering and System Safety, vol. 108, pp. 10-20, 2012. https://doi.org/10.1016/j.ress.2012.06.001
  25. M. Sharifi, G. Cheragh, K. D. Maljaii, A. Zaretalab and A. V. F. Daei, "Reliability optimization of a series-parallel k-out-of-n system with failure rate depends on working components of system," International Journal of Industrial Engineering: Theory, Applications and Practice, vol. 22, no. 4, pp. 438-453, 2015.
  26. R. A. Bakkiyaraj and N. Kumarappan, "Optimal reliability planning for a composite electric power system based on Monte Carlo simulation using particle swarm optimization," International Journal of Electrical Power and Energy Systems, vol. 47, pp. 109-116, 2013. https://doi.org/10.1016/j.ijepes.2012.10.055
  27. C. Elegbede, C. Chu, K. H. Adjallah and F. Yalaoui, "Reliability allocation through cost minimization," IEEE Transactions on Reliability, vol. 52, no. 1, pp. 106-111, 2003. https://doi.org/10.1109/TR.2002.807242
  28. "Failure mode/ mechanism distributions," Reliability Information Analysis Center (RIAC), FMD-2013, New York, USA, 2013.

Cited by

  1. Construction of methods for ensuring the required level of safety integrity in the automated systems of control over technological processes vol.102, pp.6, 2018, https://doi.org/10.15587/1729-4061.2019.187716