DOI QR코드

DOI QR Code

Effect of Particle Pre-Treatment on Properties of Jatropha Fruit Hulls Particleboard

  • Iswanto, Apri Heri (Department of Forest Product, Faculty of Forestry, Universitas Sumatera Utara) ;
  • Febrianto, Fauzi (Department of Forest Products, Faculty of Forestry, Bogor Agricultural University) ;
  • Hadi, Yusuf Sudo (Department of Forest Products, Faculty of Forestry, Bogor Agricultural University) ;
  • Ruhendi, Surdiding (Department of Forest Products, Faculty of Forestry, Bogor Agricultural University) ;
  • Hermawan, Dede (Department of Forest Products, Faculty of Forestry, Bogor Agricultural University) ;
  • Fatriasari, Widya (Research Center for Biomaterials LIPI)
  • Received : 2018.01.04
  • Accepted : 2018.03.12
  • Published : 2018.03.25

Abstract

The objective of the research was to evaluate the effect of particle pre-treatment on physical, mechanical, and durability of jatropha fruit hulls (JFH) particleboard. The pre-treatments included were immersing in cold water, hot water, and acetic acid solution. After each treatment, the particles were dried up to 3% moisture content. Urea-formaldehyde (UF) resin was used to fabricate particleboards with board size, thickness and density target of 25 cm by 25 cm, 0.80 cm, and $0.70g/cm^3$, respectively. Board pressed at $130^{\circ}C$ for 10 minutes, and $25kg/cm^2$ pressure. The evaluation of particleboard followed the JIS A 5908-2003. Whilist their resistance to subterranean termite test (mass loss, mortality, antifeedant value and feeding rate) refers to the Indonesian standard (SNI 01.7207-2006). The physical and mechanical properties of particleboards showed that all pre-treatments decreased the pH of particles. Overall, all particle immersing treatments resulted of better physical and mechanical properties of particleboard than those of untreated ones. The acetic acid treatment resulted the best physical and mechanical properties of particleboard. Based on the mass loss of JFH particleboard, hot water and acetic acid treated particleboards were classified into weak resistance to subterranean attack. The other two treatments were classified into very weak resistance. Hot water treated particleboard provided the highest mortality and antifeedant as much as 87.40% and 34.20%, respectively. Based on antifeedant classification, hot water treated particleboards were classified into moderately strong resistance, while other treatments were categorized into weak resistance. The lowest feeding rate value ($45.30{\mu}g/termite/day$) was attained by hot water treatment.

Keywords

References

  1. Colak, S., olakgglu, G.C. 2006. Effects of Wood Species and Adhesive Types on The Amount of Volatile Acetic Acid of Plywood by Using Desiccator-Method. Holz als Roh-und Werkstoff 64: 513-514. https://doi.org/10.1007/s00107-006-0108-x
  2. Febrianto, F., Royama, L.I., Hidayat, W., Bakar, E.S., Kwon, J.H., Kim, N.H. 2009. Development of Oriented Strand Board from Acacia Wood (Acacia mangium Willd): Effect of Pretreatment of Strand and Adhesive Content on the Physical and Mechanical Properties of OSB. Journal of the Korean Wood Science & Technology 37(2): 121-127
  3. Freeman, H.G. 1959. Relation Between Physical and Chemical Properties of Wood and Adhesion. Forest Product Journal 9(12): 451-458.
  4. Harmsen, P.F.H., Huijgen, W.J.J., Lopez, L.M.B., Bakker, R.R.C. 2010. Literature Review of Physical and Chemical Pre-treatment Processes for Lignocellulosic Biomass. Project Report. Wageningen, Germany.
  5. Hadi, Y.S. 1991. Pengaruh Perendaman Panas dan Asetilasi selumbar Terhadap Sifat Papan Partikel. [Dissertation]. Bogor: Graduated Program, Bogor Agricultural University.
  6. He, G., Riedl, B. 2004. Curing Kinetics of Phenol Formaldehyde Resin and Wood-Resin Interactions In The Presence of Wood Substrates. Wood Science and Technology 38: 69-81.
  7. Indonesian National Standard. 2006. Wood and Wood Products Resistance Test to Wood Destroying Organism. Indonesian National Standard Bureau, Jakarta, Indonesia.
  8. Iswanto, A.H., Simarmata, J., Fatriasari, W., Azhar, I., Sucipto, S., Hartono, R. 2017. Physical and Mechanical Properties of Three-Layer Particleboards Bonded With UF and UMF Adhesives. Journal of the Korean Wood Science & Technoloy 45(6): 787-796.
  9. Iswanto, A.H., Febrianto F., Wahyudi, I., Hwang, W.J., Lee, S.H., Kwon, J.H., Kwon, S.M., Kim, N.H., Kondo, T. 2010. Effect of Pre-treatment Techniques on Physical, Mechanical and Durability Properties of Oriented Strand Board Made from Sentang Wood (Melia excelsa Jack). Journal of the Faculty Agriculture, Kyushu University 55(2): 371-377.
  10. Jasni., Sulastiningsih, I.M. 2004. The Resistance of Treated Rubberwood Particleboard to The Drywood Termite (Cryptotermes cynocephalus Light). J Penelitian Hasil Hutan 22(2): 69-74.
  11. Johns, W.E., Niazi, K.A. 1980. Effect of pH and Buffering Capacity of Wood on The Gelation of Urea Formaldehyde Resin. Wood and Fiber Science 12(4): 256-263.
  12. Kamal, I., Poh, K.M., Eng, T.Y., Ren, X.J, Ashaari, Z. 2010. Buffering Capacity of Fast Growing Species and Curing Time of UF Resin Modified With Zinc Borate and Monoammonium Phospate. American Journal of Applied Science 7(8): 1079-1082. https://doi.org/10.3844/ajassp.2010.1079.1082
  13. Kanai, K., Azuma, J.I., Nishimoto, K. 1982. Studies on Digestive System of Termites: I. Digestion of Carbohydrates by Termite Coptotermes formosanus Shiraki. J. Wood Research 68: 47-57
  14. Kelly, M.W. 1977. Critical Literature Review of Relationship Between Processing Parameter and Physical Properties of particleboard. General Technical Report FPL-10. U.S. Department of Agriculture Forest Service and Forest Products Laboratory University of Wisconsin.
  15. Kose, C., Terzi, E., Buyuksari, U., Avei, E., Ayrilmis, N., Kartal, S.N., Imamura, Y. 2011. Particleboard and MDF Panels Made From A Mixture of Wood and Pinecones: Resistance to Decay Fungi and Termites Under Laboratory Conditions. BioResources 6(2): 2045-2054.
  16. Krilov, A., Lasander, W.H. 1988. Acidity of Heartwood and Sapwood in Some Eucalyptus Species. Holzforschung 42(4): 253-258. https://doi.org/10.1515/hfsg.1988.42.4.253
  17. Langum, C.E. 2007. Characterization of Pacific Northwest Softwoods For Wood Composites Production. [Thesis]. Washington State University, USA.
  18. Malanit, P., Barbu, M.C., Fruhwald A. 2009. The Gluability and Bonding Quality of an Asian Bamboo (Dendrocalamus asper) for The Production of Composite Lumber. Journal of Tropical Forest Science 21(4): 361-368.
  19. Maulana, S., Busyra, I., Fatrawana, A., Hidayat, W., Sari, R.K., Sumardi, I., Wistara, I.N.J., Lee, S.H., Kim, N.H., Febrianto, F. 2017. Effects of Steam Treatment on Physical and Mechanical Properties of Bamboo Oriented Strand Board. Journal of the Korean Wood Science & Technology 45(6): 872-882. https://doi.org/10.5658/WOOD.2017.45.6.872
  20. Pan, Z., Zheng, Yi., Zhang, R., Jenkins, B.M. 2007. Physical Properties of Thin Particleboard Made From Saline Eucalyptus. Industrial Crops and products 26: 185-194. https://doi.org/10.1016/j.indcrop.2007.03.006
  21. Paridah, M.T., Chin, A.M.E., Zaidon, A. 2001. Bonding Properties of Azadirachta excelsa. Journal of Tropical Forest Products 7: 161-171.
  22. Park, B.D., Kim, Y.S., Rield, B. 2001. Effect of wood-fiber characteristics on medium density fiberboard (MDF) performance. Journal of the Korean Wood Science and Technology 29: 27-35.
  23. Podgorski, L., Chevet, B., Onic, L., Merlin, A. 2000. Modification of Wood Wettability by Plasma and Corona Treatments. International Journal of Adhesion and Adhesives 20: 103-111. https://doi.org/10.1016/S0143-7496(99)00043-3
  24. Sernek, M. 2002. Comparative Analysis of Inactivated Wood Surface. [Dissertation]. Virginia Polytechnic Institute and State University. Blacksburg, Virginia.
  25. Sornnuwat, Y., Vongkaluang, C., Yoshimura, T., Tsunoda, K., Takahashi, M. 1995. Tunneling of Subterranean Termites, Coptotermes Gestroi Wasmann and Coptotermes Formosanus Shiraki, Into Gravel Physical Barriers. Japanese Journal of Environmental Entomology and Zoology 7(1): 13-19.
  26. Sudradjat, R., Tresnawati, D., Setiawan, D. 2005. Manufacture of Activated Charcoal from Jatropha Seed Shell. Jurnal Penelitian Hasil Hutan 23(2): 143-162
  27. Sujadi. 1985. Penentuan Struktur Senyawa Organik. Jakarta (ID): Ghalia Indonesia Pr.
  28. Syamani, F.A., Massijaya, M.Y., Subiyanto, B. 2011. Termite Resistant Properties of Sisal Board. Insects 2(4): 462-468. https://doi.org/10.3390/insects2040462
  29. [TAPPI] Technical Association of Pulp and Paper Industry T 4 os-59. 1959. One Percent Caustic Soda Solubility of Wood. Atlanta (US): TAPPI Pr.
  30. TAPPI] Technical Association of Pulp and Paper Industry T 1 os-50. 1950. Water Solubility of Wood. Atlanta (US): TAPPI Pr.
  31. Tascioglu, C., Yoshimura, T., Tsunoda, K. 2013. Biological Decay and Termite Resistanceof Post-Treated Wood-Based Composites Under Protected Above-Ground Condition: A Preliminary Study after 36 Months of Exposure. BioResources 8(1): 833-843.
  32. Tsoumis, G. 1991. Science and Technology of Wood: Structure, Properties, Utilization. Van Nostrand Reinhold, New York.
  33. Xing, C., Zhang, S.Y., Deng, J. 2004. Effect of Wood Acidity and Catalyst on UF Resin Gel Time. Holzforschung 58: 408-412.
  34. Zanetti, M., Pizzi, A. 2003. Upgrading of MUF Resins by Buffering Additives. Part 2: Hexamine Sulphate Mechanisms and Alternate Buffers. Journal of Applied Polymer Science 90: 215-226. https://doi.org/10.1002/app.12635