DOI QR코드

DOI QR Code

FE validation of the equivalent diameter calculation model for grouped headed studs

  • Spremic, Milan (University of Belgrade, Faculty of Civil Engineering) ;
  • Pavlovic, Marko (Delft University of Technology, Faculty of Civil Engineering and Geosciences) ;
  • Markovic, Zlatko (University of Belgrade, Faculty of Civil Engineering) ;
  • Veljkovic, Milan (Delft University of Technology, Faculty of Civil Engineering and Geosciences) ;
  • Budjevac, Dragan (University of Belgrade, Faculty of Civil Engineering)
  • 투고 : 2017.09.05
  • 심사 : 2017.11.03
  • 발행 : 2018.02.10

초록

Existing design codes for steel-concrete composite structures give only general information about the shear connection provided by headed studs in group arrangement. Grouting of the openings in prefabricated concrete slabs, where the grouped headed studs are placed in the deck pockets is alternative to cast-in-place decks to accomplish fast execution of composite structures. This paper considers the possibility to reduce the distance between the studs within the group, bellow the Eurocode limitations. This may lead to increased competitiveness of the prefabricated construction because more studs are placed in the group if negative effectives of smaller distances between studs are limited. The main purpose of this work is to investigate these limits and propose an analytical calculation model for prediction of the shear resistance of grouped stud arrangements in the deck pockets. An advanced FEA model, validated by results of push-out experiments, is used to analyze the shear behavior of the grouped stud with smaller distance between them than recommended by EN 1994-1. Calculation model for shear resistance, which is consistent with the existing Eurocode rules, is proposed based on a newly introduced equivalent diameter of the stud group, $d_G$. The new calculation model is validated by comparison to the results of FE parametric study. The distance between the studs in the longitudinal direction and the number of stud rows and columns in the group are considered as the main variables.

키워드

과제정보

연구 과제 주관 기관 : Serbian Ministry of Education, Science and Technological Development

참고문헌

  1. ABAQUS (2013), Documentation 6.11; Dassault system.
  2. An, L. and Cederwall, K. (1996), "Push-out tests on studs in high strength and normal strength concrete", J. Constr. Steel Res., 36(1), 15-29. https://doi.org/10.1016/0143-974X(94)00036-H
  3. ANSI/AISC 360-05 (2005), An American National Standard, Specification for Structural Steel Buildings; American Institute of Steel Construction, Chicago, IL, USA.
  4. Eurocode 2, EN1992-1-1 (2004), Design of Concrete Structures, General Rules and Rules for Buildings; CEN European Committee for Standardization.
  5. Eurocode 4, EN1994-1-1 (2004), Design of composite steel and concrete structures. Part 1-1: General rules and rules for buildings, European Committee for Standardization; Brussels, Belgium.
  6. Eurocode 4, EN1994-2 (2008), Design of composite steel and concrete structures. Part 2: General rules and rules for bridges, European Committee for Standardization; Brussels, Belgium.
  7. Guezouli, S., Lachal, A. and Nguyen, Q.H. (2013), "Numerical investigation of internal force transfer mechanism in push-out tests", Eng. Struct., 52, 140-152 https://doi.org/10.1016/j.engstruct.2013.02.021
  8. Oehlers, D. (1980), "Stud shear connectors for composite beams", Ph.D. Thesis; Department of Engineering, University of Warwick, March 1980.
  9. Okada, J. and Lebet, J.P. (2000), "Push-out tests for grouped arrangement of stud connectors", Report No ICOM 420; EPFLICOM Lausanne, September 2000.
  10. Okada, J., Yoda, T. and Lebet, J.P. (2006), "A study of the grouped arrangements of stud connectors on shear strength behavior", Struct. Eng./Earthq. Eng., 23(1), 75-89. https://doi.org/10.2208/jsceseee.23.75s
  11. Pallares, L. and Hajjar, J.F. (2010), "Headed steel stud anchors in composite structures, Part I: Shear", J. Constr. Steel Res., 66, 198-212. https://doi.org/10.1016/j.jcsr.2009.08.009
  12. Pavlovic, M., Markovic, Z., Veljkovic, M. and Budevac, D. (2013), "Bolted shear connectors vs. headed studs behaviour in push-out tests", J. Constr. Steel Res., 88, 134-149 https://doi.org/10.1016/j.jcsr.2013.05.003
  13. Shim, C.S., Lee, P.G., Kim, D.W. and Chung, C.H. (2008), "Effects of group arrangement on the ultimate strength of stud shear connection", Proceedings of the 2008 Composite Construction in Steel and Concrete Conference VI, ASCE Conference, Tabernash, CO, USA, July. DOI: 10.1061/41142(396)8
  14. Spremic, M., Markovic, Z., Veljkovic, M. and Budjevac, D. (2013), "Push-out experiments of headed shear stud in group arrangement", Adv. Steel Constr., Int. J., 9(2), 170-191.
  15. Spremic, M., Markovic, Z. and Veljkovic, M. (2017a), "Recommendations for the design of grouped headed studs", Steel Construction - Design and Research, 10(2), 145-153 https://doi.org/10.1002/stco.201710018
  16. Spremic, M., Markovic, Z., Veljkovic, M. and Budjevac, D. (2017b), "Shear resistance design of headed studs in group arrangement", Engineering Structures 2017. [In Review]
  17. Xu, C., Sugiura, K., Wu, C. and Su, Q. (2012), "Parametrical static analysis on group studs with typical push-out tests", J. Constr. Steel Res., 72, 84-96. https://doi.org/10.1016/j.jcsr.2011.10.029
  18. Xue, D., Liu, Y., Yu, Z. and He, J. (2012), "Static behavior of multi-stud shear connectors for steel-concrete composite bridge", J. Constr. Steel Res., 74, 1-7. https://doi.org/10.1016/j.jcsr.2011.09.017

피인용 문헌

  1. Research on shear distribution of perfobond connector groups with rubber rings vol.38, pp.4, 2021, https://doi.org/10.12989/scs.2021.38.4.399