DOI QR코드

DOI QR Code

Influence of stiffener edge on the buckling load of holed composite plates

  • Zakeri, Mahnaz (Aerospace Engineering Department, K.N. Toosi University of Technology) ;
  • Mozaffari, Ali (Aerospace Engineering Department, K.N. Toosi University of Technology) ;
  • Katirae, Mohamad A. (Aerospace Engineering Department, K.N. Toosi University of Technology)
  • 투고 : 2018.06.02
  • 심사 : 2018.12.02
  • 발행 : 2018.12.10

초록

In this paper, buckling load of edge stiffened composite plates is assessed. The effect of stiffener edge size, circular hole, and the fiber orientation angle on buckling behavior of composite plates under uni-axial compressive load is investigated. This paper includes two parts as experimental and numerical studies. L-shape composite plates are manufactured in three different layups. Then the buckling loads are experimentally determined. Subsequently, by using the numerical simulation, the size variation effects of stiffener edge and circular cutout on the plate buckling loads are analyzed in five different layups. The results show that cutout size, stiffener edge height and fiber orientation angle have important effects on buckling load. In addition, there is an optimum height for stiffener edge during different conditions.

키워드

참고문헌

  1. Abolghasemi, S., Shaterzadeh, A.R. and Rezaei, R. (2014), "Thermo-mechanical buckling analysis of functionally graded plates with an elliptic cutout", Aerosp. Sci. Technol., 39(1), 250-259. https://doi.org/10.1016/j.ast.2014.10.004
  2. Aktas, M. and Balcioglu, H. (2014), "Buckling behavior of pultruded composite beams with circular cutouts", Steel Compos. Struct., Int. J., 17(4), 359-370. https://doi.org/10.12989/scs.2014.17.4.359
  3. American Society for Testing and Materials (1995), Standard test method for in-plane shear response of polymer matrix composite materials by tensile test of a ${\pm}45^{\circ}$ laminate-Designation D3518; ASTM International, West Conshohocken, PA, USA.
  4. American Society for Testing and Materials (2000), Standard test method for tensile properties of polymer matrix composite materials-Designation D3039; ASTM International, West Conshohocken, PA, USA.
  5. American Society for Testing and Materials (2001), Standard test method for determining the compressive properties of polymer matrix composite laminates using a combined loading compression (CLC) test Fixture-Designation D6641; ASTM International, West Conshohocken, PA, USA.
  6. Baily, R. and Wood, J. (1997), "Post buckling behavior of square compression loaded graphite epoxy panels with square and elliptical cut-outs", Thin-Wall. Struct., 28(3), 373-397. https://doi.org/10.1016/S0263-8231(97)00052-9
  7. Biswal, M., Sahu, S., Asha, A. and Nanda, N. (2016), "Hygrothermal effects on buckling of composite shellexperimental and FEM results", Steel Compos. Struct., Int. J., 22(6), 1445-1463. https://doi.org/10.12989/scs.2016.22.6.1445
  8. Bohlooly, M. and Mirzavand, B. (2015), "Closed form solutions for buckling and postbuckling analysis of imperfect laminated composite plates with piezoelectric actuators", Compos.: Part B, 72(1), 21-29. https://doi.org/10.1016/j.compositesb.2014.10.049
  9. Bohlooly, M. and Mirzavand, B. (2016), "Thermomechanical buckling of hybrid cross-ply laminated rectangular plates", Adv. Compos. Mater., 65(11), 1780-1790.
  10. Britt, V. (1993), "Shear and compression buckling analysis for anisotropic panels with centrally located elliptical cutouts", AIAA, 32(11), 2293-2299.
  11. Chen, Q. and Qiao, P. (2014), "Post-buckling analysis of composite plates under combined compression and shear loading using finite strip method", Finite Elem. Anal. Des., 83(1), 33-42. https://doi.org/10.1016/j.finel.2014.01.002
  12. Department of Defense United States America (2002), The composite material handbook-MIL 17: polymer matrix composite guidelines for characterization of structure materials; ASTM International, PA, USA.
  13. Desalvo, G, (1983), ANSYS Engineering Analysis System Verification Manual, Swanson Analysis System, Houston, KA, USA.
  14. Eladi, F. and Alecakir, S. (2006), "Damage tolerance of stiffened composite panels with cutouts", J. Reinf. Plast. Compos., 25(13), 1341-1351. https://doi.org/10.1177/0731684406065070
  15. Ghannadpour, S.A.M., Najafi, A. and Mohammadi, B. (2006), "On the buckling behavior of cross-ply laminated composite plates due to circular/elliptical cutouts", Compos. Struct., 75(3), 3-7. https://doi.org/10.1016/j.compstruct.2006.04.071
  16. Hyre, M. and Lee, H. (1991), "The use of curvilinear fiber format to improve buckling resistance of composite plates with central circular holes", Compos. Struct., 18(3), 239-261. https://doi.org/10.1016/0263-8223(91)90035-W
  17. Jain, P. and Kumar, A. (2004), "Post buckling response of square laminates with a central circular/elliptical cutout", Compos. Struct., 65(2), 179-185. https://doi.org/10.1016/j.compstruct.2003.10.014
  18. Jamali, M., Shojaee, T., Kolahchi, R. and Mohammadi, B. (2016), "Buckling analysis of nanocomposite cut out plate using domain decomposition method and orthogonal polynomials", Steel Compos. Struct., Int. J., 22(3), 691-712. https://doi.org/10.12989/scs.2016.22.3.691
  19. Jaunky, N. (2001), "Progressive failure studies of composite panels with and without cutouts", NASA Langley Res. Center, VA, USA, September.
  20. Kumar, D. and Singh, S.B. (2010), "Effects of boundary conditions on buckling and post buckling responses of composite laminate with various shaped cutouts", Compos. Struct., 92(3),769-779. https://doi.org/10.1016/j.compstruct.2009.08.049
  21. Kumar, D. and Singh, S.B. (2011), "Load interaction curves and post-buckling response of composite laminate with circular cutout under combined in-plane loading", Compos.: Part B, 42(5),1189-1195.
  22. Larsson, P. (1989), "On buckling of orthotropic stretched plates with circular holes", Compos. Struct., 11(11), 121-134. https://doi.org/10.1016/0263-8223(89)90064-0
  23. Lin, C. and Kuo, C. (1989), "Buckling of Laminated Plates with Holes", J. Compos. Mater., 23(6), 536-553. https://doi.org/10.1177/002199838902300601
  24. Lopatin, A.V. and Morozov, E.V. (2013), "Buckling of a uniformly compressed rectangular SSCF composite sandwich plate", Compos. Struct., 105(1), 108-115. https://doi.org/10.1016/j.compstruct.2013.04.036
  25. Lu, H., Li, J., Nie, C., Duan, B., Yin, W., Yin, J., Hui, D. and He, X. (2017), "Study on buckling response in electrospun fiber with periodic structure", Compos.: Part B, 113(1), 270-277. https://doi.org/10.1016/j.compositesb.2017.01.033
  26. Martin, J. (1972), "Buckling and post buckling of laminated composite square plates with reinforced central holes", Ph.D. Dissertation; Case Western Reserve University, Cleveland, OH, USA.
  27. Moen, C. and Schafer, B.W. (2009), "Elastic buckling of thin plates with holes in compression or bending", Thin-Wall. Struct., 47(12), 1597-1607. https://doi.org/10.1016/j.tws.2009.05.001
  28. Narayana, A.L., Kumara, R.V. and Rao, G.K. (2018), "Effect of volume fraction on the thermal buckling analysis of laminated composite plate with square/rectangular cutout", Mater. Today: Proceedings of 7th Int. Conf. Materials Processing and Characterization, 5(1), 5819-5829.
  29. Nemeth, M. (1988), "Buckling behavior of compression-loaded symmetrically laminated angle-ply plates with holes", AIAA J., 26(3), 330-336. https://doi.org/10.2514/3.9893
  30. Nemeth, M. (1989), "Buckling and post buckling behavior of square compression-loaded graphite-epoxy plates with circular cutouts", Proceedings of Conference on Fibrous Composites in Structural Design, VA, USA, November.
  31. Niu, M.Y. (1988), Airframe Structural Design, Lockheed Aeronautical System Company Burbank, CA, USA.
  32. Oterkus, E. Barut, A. and Madenci, A. (2004), "Buckling of composite plates with a reinforced circular cutout subjected to uniform and non-uniform compression", Structural Dynamics, and Materials Conference, VA, USA.
  33. Sun, F., Wang, P., Li, W., Fan, H. and Fang, D. (2017), "Effects of circular cutouts on mechanical behaviors of carbon fiber reinforced lattice-core sandwich cylinder", Compos. Part A: Appl. Sci. Manuf., 100(1), 313-323. https://doi.org/10.1016/j.compositesa.2017.05.029
  34. Talib, A.R., Ramadhan, A., Rafie, A.S. and Zahari, R. (2013), "Influence of cut-out hole on multi-layer Kevlar-29/epoxy composite laminated plates", Mater. Des., 43(1), 89-98. https://doi.org/10.1016/j.matdes.2012.06.001
  35. Tercan, M. and Aktas, M. (2009), "Buckling behavior of $1{\time}1$ rib knitting laminated plates with cutouts", Compos. Struct., 89(2), 245-252. https://doi.org/10.1016/j.compstruct.2008.07.030
  36. Umut, T. (2013), "Application of a new extended layerwise approach to thermal buckling load optimization of laminated composite plates", Steel Compos. Struct., Int. J., 14(3), 283-293. https://doi.org/10.12989/scs.2013.14.3.283
  37. Upadhyay, A.K. and Shukla, K.K. (2013), "Post-buckling behavior of composite and sandwich skew plates", Int. J. Non-Linear Mech., 55(1), 120-127. https://doi.org/10.1016/j.ijnonlinmec.2013.05.010
  38. Wang, V., Feng, C., Zhao, Z., Lu, F. and Yang, J. (2018), "Torsional buckling of graphene platelets (GPLs) reinforced functionally graded cylindrical shell with cutout", Compos. Struct., 197(1), 72-79. https://doi.org/10.1016/j.compstruct.2018.05.056
  39. Yazici, M. (2008), "Influence of cut-out variables on buckling behavior of composite plates", J. Reinf. Plast. Compos., 28(19), 2325-2339. https://doi.org/10.1177/0731684408092058

피인용 문헌

  1. Effect of crack location on buckling analysis and SIF of cracked plates under tension vol.35, pp.2, 2018, https://doi.org/10.12989/scs.2020.35.2.215