DOI QR코드

DOI QR Code

A Fundamental Study on the Pullout Strength Equation of High Strength Anchor for Asphalt Pavement

아스팔트용 고강도 앵커시스템의 인발강도식 검토에 관한 기초적 연구

  • Choi, Jaemin (Eumseong Water Supply Office) ;
  • Lee, Seungyong (Department of Civil Engineering, Korea National University of Transportation) ;
  • Sung, Kitae (Department of Civil Engineering, Korea National University of Transportation) ;
  • Han, Youngdoo (Center Synthesis Safety Technique Institute)
  • Received : 2017.04.06
  • Accepted : 2017.09.26
  • Published : 2017.09.30

Abstract

In order to investigate the basic performance of the high strength anchor for asphalt road subjected to tensile load, the static pullout test was carried out and the pullout strength of the asphalt anchor was analyzed. In the pullout test, the depth of anchor, depth of pavement, diameter of anchor, type of anchor, experimental temperature, epoxy type and amount of anchor were used as test variables. As a result, the steel strength of asphalt anchor was 1.08 times higher than that of conventional concrete anchor, therefore it is considered appropriate to use the steel strength formula of concrete anchor for asphalt anchor. Compared with the proposed formula, the pullout load obtained from the test of the asphalt anchor was within ${\pm}10%$. The ratio of the projected area of the asphalt anchor is similar as that of the concrete anchor.

인장하중을 받는 아스팔트 도로용 고강도 앵커의 강도특성에 관한 기초 성능을 규명하기 위해 앵커 매립깊이, 포장두께, 앵커 직경, 앵커 종류, 실험 온도, 에폭시 종류, 그룹인발 수량 등을 실험변수로 하여 정적 인발실험을 실시하고, 아스팔트 앵커의 인발강도에 대하여 분석을 실시하였다. 그 결과 아스팔트 앵커의 강재강도는 기존 콘크리트 앵커의 강재강도식을 적용하면 1.08배 이상의 안전율을 확보할 수 있으므로 콘크리트 앵커 강재강도식을 사용하여도 무관한 것으로 나타났다. 아스팔트 앵커의 실험을 통해 얻은 인발하중을 제안식과 비교하면 약 ${\pm}10%$ 이내의 오차로 근사치를 나타내고 있다. 이로부터 아스팔트 앵커의 경우에도 콘크리트 앵커와 동일한 투영면적의 비가 성립될 수 있을 것으로 판단된다.

Keywords

References

  1. Ick Hyun Kim, Dong Uk Choi, Sung Chul Chun, Deuk Won Lee and Moon Hee Yang (2004). "Comparison of test results of anchors with design strength." Proceedings of the Korea Concrete Institute, Vol. 16, No. 1, pp.71-95.
  2. Jung Bum Jang, Yong Pyo Suh and Jong Rim Lee (2008). "A study on the evaluation of concrete breakout strength for cast-in-place anchor with crack." Journal of the Korean Society of Civil Engineers, Vol. 24, No. 3A, pp.647-652.
  3. Korea Concrete Institute (2012). Concrete design code and commentary, pp.463-498.
  4. Korea Concrete Institute (2010). Design method and examples for concrete anchor(2nd edition), pp.23-67.
  5. Kwang Myong Lee, Chin Yong Lee, Sang Hwa Jung and Seul Woo Choi (2009). "Tensile and shear test method for post-installed mechanical anchors embedded in concrete." Proceedings of the Korea Concrete Institute, Vol. 21, No. 1, pp.97-98.
  6. Min Tae Kim, Sok Hwan Choi, Chang Bin Joh, Byung Suk Kim and Jung Woo Lee (2013). "The breakout strength of anchors under tension according to the embedment length and edge distance." Proceedings of the Korea Concrete Institute, Vol. 25, No. 1, pp.353-354.
  7. Sung Kyun Paek, Ho Seop Kim, Young Soo Yoon and Sang Yoon Kim (2001). "Fracture behavior of cast-in-place headed anchors to concrete." Journal of the Korea Institute for Structural Maintenance Inspection, Vol. 5, No. 3, pp.141-152.1.