The Transactions of The Korean Institute of Electrical Engineers (전기학회논문지)

The Korean Institute of Electrical Engineers (대한전기학회)
권호 표지
DOI QR코드

DOI QR Code

Analysis of IPMSM Temperature Characteristics based on Stator Design Parameters

600W급 IPMSM의 고정자 설계 변수 변화에 따른 온도 특성 분석 및 고찰

  • Go, Duk-Hwa (Dept. of Electrical Engineering, Changwon National University) ;
  • Kim, Yong-Tae (Motor R&D Center, S&T Motiv) ;
  • Kim, Gyu-Tak (Dept. of Electrical Engineering, Changwon National University)
  • Received : 2017.01.24
  • Accepted : 2017.07.24
  • Published : 2017.08.01
Download PDF
⟨ Previous Next ⟩

Abstract

In this paper, the temperature characteristics by change the width of teeth and yoke in the stat or parameters were analyzed. An initial model of fill factor 45 [%] was produced. Through the experiment, the validity of the temperature analysis using the thermal equivalent circuit method was verified. So, initial model was selected as basic model. Also, temperature characteristic analysis was performed for each width change of the stator teeth and yoke, and the effects of the width of stator teeth and yoke on the temperature characteristics were analyzed.

Keywords

References

  1. C. Feng, P. Yulong, L. Xinmei, G. Bin, and C. Shukang, "The Performance Research of Starter-Generator Basedon Reluctance Torque Used in HEV," IEEE Trans. on Magn., volume 45, no. 1, pp. 635-38, 2009. https://doi.org/10.1109/TMAG.2008.2008857
  2. Won-Sik Lee, Deak-Hwa Go, Yong-Tae Kim, Gyu-Won Cho, Gyu-Tak Kim "The Increase of heat capacity for improved the output characteristics of the rare earth permanent magnet motor," KIEE summer conference, BP 1, July. 2016
  3. Lim jae-won, Seo jang-Ho, Lee Sang-Yub, Jung Hyunkyo, "Thermal Network Analysis of Interior Permanent Magnet Machine," The Korean society for railway, 2009 spring conference, pp. 527-532, May. 2009
  4. Kye Seung-Hyun, "A Study on Thermal Characteristics Analysis of IPMSM by Using Thermal Equivalent Circuit Network", Master's Thesis, Chagwon national university. 2012
  5. S.K. Chowdhury, P.K Baski, "A simple lumped parameter thermal model for electrical machine of TEFC design", Power Electronics, Drives and Energy Systems(PEDES) & 2010 Power India, 2010 Joint International Conference on, pp. 1-7, 2010.
  6. Chaofan Shen, "Thermal Analysis of Permanent Magnet Brushless DC Motor For Electric Vehicle", Master's Thesis, Yeungnam University, 2012
  7. T.J Roberts., "Determination of the Thermal Constants of the Heat Flow Equations of Electrical Machines", Proc IME, Vol. 184, Pt 3E, pp. 84-92, 1969
  8. Kye, Seung-Hyun; Jeong, Tae-Seok; Cho, Gyu-Won; Jang, Ki-Bong; Kim, Gyu-Tak; "Thermal Analysis of IPMSM According to Current Vector Control Method" The Transactions of The Korean Institute of Electrical Engineers, Vol 61, pp.1420-1425, 2012 https://doi.org/10.5370/KIEE.2012.61.10.1420
  9. Seok-Hyeon Woo, Gyu-Won Cho, Ki Bong Jang, Gyu Tak Kim, "Coreloss Calculation of IPMSM Using the Modifed Steinmetz Equation", KIEE fall conference, EMP 14, october. 2011