DOI QR코드

DOI QR Code

Dynamic numerical simulation of plastic deformation and residual stress in shot peening of aluminium alloy

  • Ullah, Himayat (Centre of Excellence in Applied Sciences and Technology (CESAT)) ;
  • Ullah, Baseer (Centre of Excellence in Applied Sciences and Technology (CESAT)) ;
  • Muhammad, Riaz (Department of Mechanical Engineering, CECOS University of IT and Emerging Sciences)
  • 투고 : 2016.11.27
  • 심사 : 2017.03.15
  • 발행 : 2017.07.10

초록

Shot peening is a cold surface treatment employed to induce residual stress field in a metallic component beneficial for increasing its fatigue strength. The experimental investigation of parameters involved in shot peening process is very complex as well as costly. The most attractive alternative is the explicit dynamics finite element (FE) analysis capable of determining the shot peening process parameters subject to the selection of a proper material's constitutive model and numerical technique. In this study, Ansys / LS-Dyna software was used to simulate the impact of steel shots of various sizes on an aluminium alloy plate described with strain rate dependent elasto-plastic material model. The impacts were carried out at various incident velocities. The influence of shot velocity and size on the plastic deformation, compressive residual stress and force-time response were investigated. The results exhibited that increasing the shot velocity and size resulted in an increase in plastic deformation of the aluminium target. However, a little effect of the shot velocity and size was observed on the magnitude of target's subsurface compressive residual stress. The obtained results were close to the published ones, and the numerical models demonstrated the capability of the method to capture the pattern of residual stress and plastic deformation observed experimentally in aluminium alloys. The study can be quite helpful in determining and selecting the optimal shot peening parameters to achieve specific level of plastic deformation and compressive residual stress in the aluminium alloy parts especially compressor blades.

키워드

참고문헌

  1. Al-Obaid, Y. (1990), "Three-dimensional dynamic finite element analysis for shot-peening mechanics", Comput. Struct., 36(4), 681-689. https://doi.org/10.1016/0045-7949(90)90083-E
  2. ANSYS LS-DYNA User's Guide (2015)
  3. Bhuvaraghan, B., Srinivasan, S.M., Maffeo, B., McCLain, R.D., Potdar, Y. and Prakash, O. (2010), "Shot peening simulation using discrete and finite element methods", Adv. Eng. Softw., 41(12), 1266-1276. https://doi.org/10.1016/j.advengsoft.2010.09.003
  4. Bagherifard, S., Ghelichi, R. and Guagliano, M. (2014), "Mesh sensitivity assessment of shot peening finite element simulation aimed at surface grain refinement", Surface Coat. Technol., 243, 58-64. https://doi.org/10.1016/j.surfcoat.2012.04.002
  5. Rubio-Gonzalez, C., Gomez-Rosas, G., Ruiz, R., Nait, M. and Amrouche, A. (2015), "Effect of laser shock peening and cold expansion on fatigue performance of open hole samples", Struct. Eng. Mech., 53(5), 867-880. https://doi.org/10.12989/sem.2015.53.5.867
  6. Chen, Z., Yang, F. and Meguid, S.A. (2014), "Realistic finite element simulations of arc-height development in shot-peened almen strips", J. Eng. Mater. Technol., 136(4), 041002. https://doi.org/10.1115/1.4028006
  7. Mylonas, G.I. and Labeas, G. (2011), "Numerical modelling of shot peening process and corresponding products: residual stress, surface roughness and cold work prediction", Surface Coat. Technol., 205(19), 4480-4494. https://doi.org/10.1016/j.surfcoat.2011.03.080
  8. Johnson, G.R. and Cook, W.H. (1983), "A constitutive model and data for metals subjected to large strains, high strain rates and high temperatures", Proceedings of the 7th International Symposium on Ballistics, The Hague, The Netherlands.
  9. Guagliano, M. (2001), "Relating Almen intensity to residual stresses induced by shot peening: a numerical approach", J. Mater. Proc. Technol., 110(3), 277-286. https://doi.org/10.1016/S0924-0136(00)00893-1
  10. Hassani-Gangaraj, S.M., K.S. Cho, H.J.L. Voigt, M. Guagliano and C.A. Schuh (2015), "Experimental assessment and simulation of surface Nanocrystallization by severe shot peening", Acta Materialia, 97, 105-115. https://doi.org/10.1016/j.actamat.2015.06.054
  11. Hfaiedh, N., Peyre, P., Song, H., Popa, I., Ji, V. and Vignal, V. (2015), "Finite element analysis of laser shock peening of 2050-T8 aluminum alloy", Int. J. Fatigue, 70, 480-489. https://doi.org/10.1016/j.ijfatigue.2014.05.015
  12. Hidayetoglu, T.K. (2001), "Effect of the gear finishing process on bending fatigue crack initiation and propagation in spur gears", Proc. Inst. Mech. Engineers, Part C: J. Mech. Eng. Sci., 215(7), 785-792. https://doi.org/10.1243/0954406011524144
  13. Hong, T., Ooi, J. Y. and Shaw, B. (2008), "A numerical simulation to relate the shot peening parameters to the induced residual stresses", Eng. Fail. Anal., 15(8), 1097-1110. https://doi.org/10.1016/j.engfailanal.2007.11.017
  14. Hong, T., Ooi, J.Y. and Shaw, B.A. (2008), "A three-dimensional finite element analysis of two/multiple shots impacting on a metallic component", Struct. Eng. Mech., 29(6), 709-729. https://doi.org/10.12989/sem.2008.29.6.709
  15. Jack Hetherington, A.R.F. and Harm Askes (2011), "Controlling the critical time step with the bi-penalty method", OMPDYN 2011, 3rd ECCOMAS Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering, M. F. M. Papadrakakis, V. Plevris Greece.
  16. Dai, K. and Shaw, L. (2007), "Comparison between shot peening and surface nanocrystallization and hardening processes", Mater. Sci. Eng.: A, 463(1), 46-53. https://doi.org/10.1016/j.msea.2006.07.159
  17. Majzoobi, G.H., Azizi, R. and Nia, A.A. (2005), "A threedimensional simulation of shot peening process using multiple shot impacts", J. Mater. Proc. Technol., 164, 1226-1234.
  18. Mann, P., Miao, H.Y., Gariepy, A., Levesque, M. and Chromik, R.R. (2015), "Residual stress near single shot peening impingements determined by nanoindentation and numerical simulations", J. Mater. Sci., 50(5), 2284-2297. https://doi.org/10.1007/s10853-014-8792-0
  19. Meguid, S. and L.A. Maricic (2015), "Finite element modeling of shot peening residual stress relaxation in turbine disk assemblies", J. Eng. Mater. Technol., 137(3), 031003. https://doi.org/10.1115/1.4030066
  20. Meguid, S.A., Shagal, G. and Stranart, J.C. (2002), "3D FE analysis of peening of strain-rate sensitive materials using multiple impingement model", Int. J. Impact Eng., 27(2), 119-134. https://doi.org/10.1016/S0734-743X(01)00043-4
  21. Meguid, S.A., Shagal, G., Stranart, J.C. and Daly, J. (1999), "Three-dimensional dynamic finite element analysis of shotpeening induced residual stresses", Finite Element. Anal. Des., 31(3), 179-191. https://doi.org/10.1016/S0168-874X(98)00057-2
  22. Mohamed Jebahi, A.G., Julie Levesque, Oussama Mechri and Kadiata, B.A. (2016), "Robust methodology to simulate real shot peening process using discrete-continuum coupling method", Int. J. Mech. Sci., 107, 21-33. https://doi.org/10.1016/j.ijmecsci.2016.01.005
  23. Nicholas, J., Carpenter, R.L.T. and Michael G. Katona (1991), "Lagrange constraints for transient finite element surface contact", Int. J. Numer. Method. Eng., 32(1), 103-128. https://doi.org/10.1002/nme.1620320107
  24. Shukla, P.P., Swanson, P.T. and Page, C.J. (2014), "Laser shock peening and mechanical shot peening processes applicable for the surface treatment of technical grade ceramics: A review", Proc. Inst. Mech. Engineers, Part B: J. Eng. Manufact., 228(5), 639-652. https://doi.org/10.1177/0954405413507250
  25. Belytschko, T. and Neal, M.O. (1991), "Contact‐impact by the pinball algorithm with penalty and Lagrangian methods", Int. J. Numer. Method. Eng., 31(3), 547-572. https://doi.org/10.1002/nme.1620310309
  26. Carlberger, T. and Stigh, U. (2007), "An explicit FE-model of impact fracture in an adhesive joint", Eng. Fract. Mech., 74(14), 2247-2262. https://doi.org/10.1016/j.engfracmech.2006.10.016
  27. Ullah, H. and Silberschmidt, V.V. (2015), "Numerical analysis of the interactive damage mechanisms in two-dimensional carbon fabric-reinforced thermoplastic composites under low velocity impacts", J. Compos. Mater., 49(25), 3127-3143. https://doi.org/10.1177/0021998314560383

피인용 문헌

  1. Simulation of prestressed ultrasonic peen forming on bending deformation and residual stress distribution vol.98, pp.1-4, 2018, https://doi.org/10.1007/s00170-018-2287-0