대한기계학회논문집A (Transactions of the Korean Society of Mechanical Engineers A)

  • 제41권4호
  • /
  • Pages.307-312
  • /
  • 2017
  • /
  • 1226-4873(pISSN)
  • /
  • 2288-5226(eISSN)
대한기계학회 (The Korean Society of Mechanical Engineers)
권호 표지
DOI QR코드

DOI QR Code

EuTroLoy 16006 분말을 이용한 내열강의 레이저 클래딩에 관한 연구(II) - 멀티패스 클래드 층의 합금 성분 분포 특성 -

Study on Laser Cladding of Heat Resisting Steel Using EuTroLoy 16006 Powder(II) - Characteristics of Alloying Elements Distribution of Multi Pass Clad Layer -

  • 투고 : 2016.08.05
  • 심사 : 2017.01.02
  • 발행 : 2017.04.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

레이저 클래딩은 아크 용접 및 용사와 같은 기존 클래딩 기술보다 우수한 장점을 가진다. 레이저 클래딩으로 형성한 클래드 층의 희석률은 낮으며 모재와의 결합력이 우수하고 결함이 거의 존재하지 않는다. 이러한 특징을 가진 레이저 클래딩을 실제 선박용 배기밸브에 적용하기에 위해 지난 제1보의 논문에서 조사한 공정변수에 따른 1 패스 클래드 층의 특성을 통해 넓은 면적에 클래딩 시 1 패스 클래드 층의 중첩이 필수적이라는 것을 알 수 있었다. 따라서 본 논문에서는 중첩률에 따른 멀티패스 클래드 층의 형상 차이를 비교하고 일정 중첩률 조건에서 EDS 및 EPMA를 통해 합금 성분 분포를 파악하였다. 실험결과, 중첩률이 증가할수록 클래드 층의 길이가 감소하고 높이가 증가하였으며 동일한 조건의 1 패스 클래드 층보다 높이가 상승하였다. 성분 분석을 통해 모재 희석이 많이 발생한 첫 번째 클래드 층에서 Fe이 높게 측정되었으나 나머지 영역에서는 희석이 감소하여 Co가 증가하고 Fe이 감소하였으며 균일한 성분 분포가 관찰되었다.

Laser cladding has some advantages compared to conventional cladding technologies such as arc welding and thermal spraying. Laser cladding produces a metallurgically well-bonded clad layer with a lower dilution ratio and few defects. Based on the characteristics of a 1-pass clad layer with many parameters, which were investigated in a previous report, it was found that it was essential to overlap a 1-pass clad layer when cladding a large area. In this study, the shape differences of multi-pass clad layers with various overlapping ratios were compared. Then, the alloying element distribution of cladding with a certain overlapping ratio was investigated using EDS and EPMA. As the overlapping ratio increased, the length of the clad decreased and its height increased. In addition, the height of the multi-pass cladding was higher than that of the 1-pass cladding under the same condition. The Fe content of the highly diluted first clad was found to be approximately 20 % in an element analysis. However in the area outside of the first clad, the Fe content was decreased to 10 % as a result of minimum dilution, and a uniform distribution of elements was found.

키워드

참고문헌

  1. Song, H. S., Choi, B. S., Yun, J. D. and Park, S. T., 2015, "Characterization of Cold Metal Transfer Welding Coated Steel," Trans. Korean Soc. Mech. Eng. A, Vol. 32, No. 10, pp. 891-896.
  2. Kim, D. W., Jun, H. K., Lee, S. H. and Chang, Y. S., 2016, "Residual Stress Analysis of Repair Welded Rail Using the ABAQUS User Subroutine," Trans. Korean Soc. Mech. Eng. A, Vol. 33, No. 7, pp. 551-558.
  3. Andersson, O. and Parker, K., 2014, "High Power Diode Laser Cladding," FABRICATING& METALWORKING, pp. 24-26.
  4. Lee, J. H., Suh, M. H. and Han, Y. H., 2000, "Laser Cladding," Journal of Welding and Joining, Vol. 18, No. 2, pp. 154-162.
  5. Ana Sofia C.M D'Oliveira, Paulo Sergio C.P. da Silva and Rui M.C. Vilar, 2002, "Microstructural Features of Consecutive Layers of Stellite 6 Deposited by Laser Cladding," Surface and Coatings Technology, Vol. 153, 203-209. https://doi.org/10.1016/S0257-8972(01)01687-5
  6. Huang, Y., 2011, "Characterization of Dilution Action in Laser-induction Hybrid Cladding," Optics &Laser Technology, Vol. 43, pp. 965-973. https://doi.org/10.1016/j.optlastec.2010.12.005
  7. Li, K., Li, D., Liu, D., Pei, G. and Sun, L., 2015, "Microstructure Evolution and Mechanical Properties of Multiple-layer Laser Cladding Coating of 308L Stainless Steel," Applied Surface Science, Vol. 340, pp. 143-150. https://doi.org/10.1016/j.apsusc.2015.02.171
  8. Smolenska, H., 2008, "Oxidation and Exhaust Gas Corrosion Resistance of The Cobalt base Clad Layers," Journal of Achievements in Materials and Manufacturing Engineering, Vol. 31, No. 2, pp. 364-372.
  9. Birol, Y., 2010, "Thermal Fatigue Testing of Stellite 6-coated Hot Work Tool Steel," Materials Science and Engineering A, Vol. 527, pp. 364-372.
  10. Kang, W. J., 2007, "A Study on Surface Transformation Hardening Process for Carbon Steel by Laser Heat Source," Master Degree Thesis at the Korea Maritime and Ocean University, Korea, pp. 74-75.