DOI QR코드

DOI QR Code

External retrofit of beam-column joints in old fashioned RC structures

  • Adibi, Mahdi (School of Civil Engineering, College of Engineering, University of Tehran) ;
  • Marefat, Mohammad S. (School of Civil Engineering, College of Engineering, University of Tehran) ;
  • Arani, Kamyar Karbasi (School of Civil Engineering, College of Engineering, University of Tehran) ;
  • Zare, Hamid (School of Civil Engineering, College of Engineering, University of Tehran)
  • 투고 : 2016.06.04
  • 심사 : 2017.01.13
  • 발행 : 2017.02.25

초록

There has been increasing attention in many countries on seismic retrofit of old fashioned RC structures in recent years. In such buildings, the joints lack transverse reinforcement and suffer inadequate seismic dimensional requirements and the reinforcement is plain bar. The behavior of the joints is governed by sliding of steel bars and diagonal shear failure is less influential. Different methods to retrofit beam-column joints have been proposed in the literature such as wrapping the joint by FRP sheets, enlargement of the beam-column joint, and strengthening the joint by steel sheets. In this study, an enlargement technique that uses external prestressed cross ties with steel angles is examined. The technique has already been used for substructures reinforced by deformed bars and has advantages such as efficient enhancement of seismic capacity and lack of damage to the joint. Three reference specimens and two retrofitted units are tested under increasing lateral cyclic load in combination with two levels of axial load. The reference specimens showed relatively low shear strength of 0.150${\surd}$($f_c$) and 0.30${\surd}$($f_c$) for the exterior and interior joints, respectively. In addition, relatively brittle behavior was observed and large deformations extended into the panel zone of the joints. The retrofit method has increased ductility ratio of the interior beam-column joints by 63%, and energy dissipation capacity by 77%, relative to the control specimen; For external joints, these values were 11%, and 94%. The retrofit method has successfully relocated the plastic joints far from the column face. The retrofit method has improved shear strength of the joints by less than 10%.

키워드

참고문헌

  1. ACI 374.1-05 (2005), Acceptance criteria for moment frames based on structural testing and commentary, Farmington Hills, Michigan, USA.
  2. ACI 374.2R-13 (2005), Guide for testing reinforced concrete structural elements under slowly applied simulated seismic loads, Farmington Hills, Michigan, USA.
  3. Altoontash, A. (2004), "Simulation and damage models for performance assessment of reinforced concrete beam-column joints", Stanford University, Ph.D. Thesis.
  4. ATC (1989), "Handbook for Seismic Evaluation of Existing Buildings ATC-22", Applied Technology Council, Redwood City, California.
  5. Barker, J.A. (1979), Reinforced Concrete Detailing, Oxford University press, 2nd Edition, London.
  6. Bedirhanoglu, I., Alper Ilki, Santiago Pujol and Nahit Kumbasar (2010), "Behavior of deficient joints with plain bars and lowstrength concrete", ACI Struct. J., 107(3), 300.
  7. Braga, F., Gigliotti, R. and Laterza, M. (2009), "R/C existing structures with smooth reinforcing bars: Experimental behaviour of beam-column joints subject to cyclic lateral loads", Open Constr. Build. Technol. J., 3, 52-67. https://doi.org/10.2174/1874836800903010052
  8. Braga, F., Gigliotti, R., Laterza, M., D'Amato, M. and Kunnath, S. (2012), "Modified steel bar model incorporating bond-slip for seismic assessment of concrete structures", J. Struct. Eng., 138(11), 1342-1350. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000587
  9. Calvi, G.M., Magenes, G. and Pampanin, S. (2002), "Relevance of beam-column joint damage and collapse in RC frame assessment", J. Earthq. Eng., 6(1), 75-100. https://doi.org/10.1080/13632460209350411
  10. Cosenza, E., Manfredi, G. and Ramasco, R. (1993), "The use of damage functional in earthquake engineering, a comparison between different methods", Earthq. Eng. Struct. Dyn. J., 22(10), 855-868. https://doi.org/10.1002/eqe.4290221003
  11. D'Amato, Braga, F., Gigliotti, R., Kunnath, S. and Laterza, M. (2012), "Validation of a Modified Steel Bar Model Incorporating Bond-Slip for Seismic Assessment of Concrete Structures", J. Struct. Eng., 138(11), 1351-1360. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000588
  12. Dimitrios, A. and Tsonos, G. (2010), "Performance enhancement of R/C building columns and beamcolumn joints through shotcrete jacketing", Eng. Struct. J., 32(3), 726-740. https://doi.org/10.1016/j.engstruct.2009.12.001
  13. Din 1045 (1959), Bestimmungen fur die Ausfuhrung von Bauwerken aus Stahlbeton, Deutscher Ausschuss fur Stahlbeton, Berlin, Koln, Germany.
  14. Duhman, C.W. (1953), The Theory and Practice of Reinforced Concrete, McGraw-Hill Book co.
  15. Edvard, N.J. and Tanner, J.L. (1996), Theory and problems of Reinforced Concrete Design, Schaum Publishing co., USA
  16. Guerrin, A. (1959), Traite De Beton Arme, Dunod, Paris.
  17. Hakuto, S., Park, R. and Tanaka, H. (1999), "Effect of deterioration of bond of beam bars passing through interior beam-column joints on flexural strength and ductility", ACI Struct. J., 96(5), 858-864.
  18. Hakuto, S., Park, R. and Tanaka, H. (2000), "Seismic Load Tests on Interior and Exterior beam-column Joints with Substandard Reinforcing Details", ACI Struct. J., 97(1), 11-25.
  19. Karayannis, C.G., Chalioris, C.E. and Sirkelis, G.M. (2008), "Local retrofit of exterior RC beam-column joints using thin RC jackets", J. Earthq. Eng. Struct. Dyn., 37(5), 727-746. https://doi.org/10.1002/eqe.783
  20. Liu, A. and Park, R. (2000), "Seismic behavior of existing moment-resisting frames with plain round reinforcing bars designed to pre-1970s codes", Proceeding of 12th world conference on earthquake engineering, Auckland, New Zealand, February.
  21. Liu, A. and Park, R. (2001), "Seismic behaviour and retrofit of pre 1970's as built exterior beam-column joint reinforced by plain bars", Bull. NZ. Soc. Earthq. Eng., 34(1), 68-81.
  22. Manfredi, G., Verderame, G.M. and Lignola, G.P. (2008), "A F.E.M. model for the evaluation of the seismic behavior of interior joints in reinforced concrete frames", Proceedings of the 14th World Conference on Earthquake Engineering, Bejing, China, October.
  23. Marthong, C., Deb, S.K. and Dutta, A. (2016), "Experimental fragility functions for exterior deficient RC beamcolumn connections before and after rehabilitation", Earthq. Struct., 10(6), 1291-1314. https://doi.org/10.12989/eas.2016.10.6.1291
  24. Marthong, C., Dutta, A. and Deb, S.K. (2013), "Seismic rehabilitation of RC exterior beam-column connections using epoxy resin injection", J. Earthq. Eng., 17(3), 378-398. https://doi.org/10.1080/13632469.2012.738284
  25. Masi, A., Santarsiero, G., Verderame, G., Russo, G., Martinelli, E., Pauletta, M. and Cortesia, A. (2009), "Capacity models of beam-column joints: provisions of european and italian seismic codes and possible improvements", Conference: Reluis Italian National Research Project, Italy, April.
  26. Pampanin, S., Calvi, G.M. and Moratti, M. (2002), "Seismic behaviour of R.C. beam-column joints designed for gravity loads", Proceeding of 12th European Conference on Earthquake Engineering, London, UK, September.
  27. Pampanin, S., Christopoulos, C. and Chen, T.H. (2006), "Development and validation of a metallic haunch seismic retrofit system for existing under-designed RC frame buildings", Earthq. Eng. Struct. Dyn., 35(14), 1739-1766. https://doi.org/10.1002/eqe.600
  28. Parate, K. and Ratnesh Kumar (2016), "Investigation of shear strength models for exterior RC beam-column joint", Earthq. Struct., 58(3), 475-514
  29. Park, R. (1989), "Evaluation of ductility of structures and structural assemblages from laboratory testing", Bull. NZ. Soc. Earthq. Eng., 22(3), 155-166.
  30. Park, R. (2002), "A Summary of results of simulated seismic load tests on RC beam-column joints, beams and columns with substandard reinforcing details", J. Earthq. Eng., 6(2), 147-174. https://doi.org/10.1080/13632460209350413
  31. Park, R., Billings, I.J., Clifton, G.C., Cousins, W.J., Filiatrault, A., Jennings, D.N., Jones, L.C.P., Perrin, N.D., Rooney, S.L., Sinclair, J., Spurr, D.D., Tanaka, H. and Walker, G. (1995), "The Hyogo-ken Nanbu Earthquake (The Great Hanshin Earthquake) of 17 January 1995", Report of the NZNSEE Reconnaissance Team, Bull. NZ. Natl. Soc. Earthq. Eng., 28(1), 1-98.
  32. Park, Y. and Ang, A. (1985), "Mechanistic seismic damage model for reinforced-concrete", Struct. Eng. J., ASCE, 111(4), 722-739. https://doi.org/10.1061/(ASCE)0733-9445(1985)111:4(722)
  33. Paulay, T. and Priestley, M.J.N. (1992), Seismic design of reinforced concrete and masonry buildings, John Wiley & Sons, Inc, New York, NY, USA.
  34. Pernot, P. (1954), Le Beton Arme, J. B. Balliere et Fils, Editeurs, Paris.
  35. Pimanmas, A. and Chaimahawan, P. (2010), "Shear strength of beamcolumn joint with enlarged joint area", Eng. Struct. J., 32(9), 2529-2545. https://doi.org/10.1016/j.engstruct.2010.04.021
  36. Priestley, M.J.N. and Park, R. (1987) "Strength and ductility of concrete bridge columns under seismic loading", ACI Struct. J., 84(1), 61-76.
  37. Rohma, C., Novak, B., Sasmal, S., Karusala, R. and Srinivas, V. (2012), "Behaviour of fibre reinforced beam-column subassemblages under reversed cyclic loading", Constr. Build. Mater. J., 36, 319-329 https://doi.org/10.1016/j.conbuildmat.2012.04.114
  38. Russo, G. and Margherita Pauletta (2012), "Seismic behavior of exterior beam-column connections with plain bars and effects of upgrade", ACI Struct. J., 109(2), 225
  39. Sezen, H., Elwood, K.J., Whittaker, A.S., Mosalam, K.M., Wallace, J.W. and Stanton, J.F. (2000), "Structural Engineering Reconnaissance of the August 17, 1999 Kocaeli (Izmit), Turkey Earthquake", Technical Rep. No., PEER 2000, 9.
  40. Sezen, H., Whittaker, A.S., Elwood, K.J. and Mosalam, K.M. (2003), "Performance of reinforced concrete buildings during the August 17, 1999 Kocaeli, Turkey earthquake, and seismic design and construction practice in Turkey", Eng. Struct. J., 25(1), 103-114. https://doi.org/10.1016/S0141-0296(02)00121-9
  41. Shafaei, J., Hosseini, A. and Marefat, M. (2014a), "Seismic retrofit of exterior RC beam-column joints by joint enlargement using prestressed steel angles", Eng. Struct. J., 81, 265-288. https://doi.org/10.1016/j.engstruct.2014.10.006
  42. Shafaei, J., Zareian, M., Hosseini, A. and Marefat, M. (2014b), "Effects of joint flexibility on lateral response of reinforced concrete frames", Eng. Struct. J., 81, 412-431. https://doi.org/10.1016/j.engstruct.2014.09.046
  43. Shigeru, H. (1995), Retrofitting of reinforced concrete moment Resisting Frames. research report Dept. Civil. Engineering, Univ. of Canterbury, NZ (supervised by R. Park and H. Tanaka) ISSN 0110-3326.
  44. Soleimani, D., Popov, E.P. and Bertero, V.V. (1979), "Hysteretic beahavior of reinforced concrete beamcolumn subassemblages", ACI J., 76(11), 1179-1195.

피인용 문헌

  1. An efficient fiber beam-column element considering flexure–shear interaction and anchorage bond-slip effect for cyclic analysis of RC structures vol.16, pp.11, 2018, https://doi.org/10.1007/s10518-018-0392-y
  2. Nonlinear modeling of cyclic response of RC beam–column joints reinforced by plain bars vol.16, pp.11, 2018, https://doi.org/10.1007/s10518-018-0399-4
  3. Effect of soil-structure interaction on seismic damage of mid-rise reinforced concrete structures retrofitted by FRP composites vol.15, pp.3, 2017, https://doi.org/10.12989/eas.2018.15.3.307
  4. Non-invasive steel haunch upgradation strategy for seismically deficient reinforced concrete exterior beam-column sub-assemblages vol.28, pp.6, 2017, https://doi.org/10.12989/scs.2018.28.6.719
  5. Experimental evaluation of external beam-column joints reinforced by deformed and plain bar vol.18, pp.1, 2020, https://doi.org/10.12989/eas.2020.18.1.113
  6. Novel steel bracket and haunch hybrid system for post-earthquake retrofit of damaged exterior beam-column sub-assemblages vol.73, pp.3, 2017, https://doi.org/10.12989/sem.2020.73.3.239
  7. Seismic strengthening of deficient RC frames using self-centering friction haunches vol.248, pp.None, 2017, https://doi.org/10.1016/j.engstruct.2021.113261