DOI QR코드

DOI QR Code

Fatigue behavior of mechanical structures welded with different filler metal

  • Alioua, Abdelkader (Department of Mechanical Engineering, Laboratory LMSR, University Djilali Liabes Sidi Bel Abbes) ;
  • Bouchouicha, Benattou (Department of Mechanical Engineering, Laboratory LMSR, University Djilali Liabes Sidi Bel Abbes) ;
  • Zemri, Mokhtar (Department of Mechanical Engineering, Laboratory LMSR, University Djilali Liabes Sidi Bel Abbes) ;
  • IMAD, Abdellatif (Laboratory of Mechanics of Lille)
  • 투고 : 2017.05.16
  • 심사 : 2017.09.18
  • 발행 : 2017.09.25

초록

This paper describes an investigation on the effect of using three different filler metals on fatigue behavior of mechanical structures welded. The welding is carried out on the steel A510AP used for the manufacture of gas cisterns and pipes. The welding process used is manual welding with coated electrodes and automatic arc welding. Compact tension CT50 specimen has been used. The three zones of welded joint; filler metal FM, heat affected zone HAZ and base metal BM have been investigated. The results show that the crack growth rate CGR is decreasing respectively in BM, FM and HAZ; however, this variation decreases when stress intensity factor SIF increases. For low values of SIF, the CGR is inferior in the over-matched filler metal of which the value of mismatch M is near unity, but for high values of M the CGR is superior, and the effect of the over-matching on CGR becomes negative. No deviation of the crack growth path has been noticed.

키워드

참고문헌

  1. Akita, M., Nakajima, M., Tokaji, K. and Shimizu T. (2006), "Fatigue crack propagation of 444 stainless steel welded joints in air and in 3% NaCl aqueous solution", Mater. Des., 27(2), 92-99. https://doi.org/10.1016/j.matdes.2004.10.004
  2. Bozic, Z.B.Z., Schmauder, S. and Mlikota, M. (2013), "Fatigue crack growth modelling in welded stiffened panels under cyclic tension", Proceeding of the 13th International Conference on Fracture, Beijing, China, June, paper M15-018.
  3. Burzic, M., Prokic-Cvetkovic, R., Popovic, O. and Burzic, Z. (2014), "Effect of structural heterogeneity on the fracture mechanics parameters of welded joints of A. 387 steel", Sci. Tech. Rev., 64(4), 39-44.
  4. Haušild, P., Berdin, C. and Bompard, P. (2005), "Prediction of cleavage fracture for a low-alloy steel in the ductile-to-brittle transition temperature range", Sci. Eng. A, 391(1-2), 188-197. https://doi.org/10.1016/j.msea.2004.08.067
  5. Inal, K., M'cirdi, L., Lebrun, J.L. and Barbier, G. (2000), "Mechanical behaviour analysis of phase interaction in a rolled and a cast duplex stainless steels, proceedings of the sixth international conference on Duplex stainless steels", Venise, 173-182.
  6. Itatani, M., Fukakura, J., Asano, M., Kikuchi, M. and Chujo, N. (1994), "Fatigue crack growth behavior of weld heat-affected zone of type 304 stainless steel in high temperature water", Nuclear Eng. Des., 153(1), Pages 27-34. https://doi.org/10.1016/0029-5493(94)90018-3
  7. Khurshid, M., Barsoum, Z. and Mumtaz, N.A. (2012), "Ultimate strength and failure modes for fillet welds in high strength steels", Mater. Des., 40, 36-42. https://doi.org/10.1016/j.matdes.2012.03.048
  8. Lei, Y.P., Shi, Y.W., Murakawa, H. and Luo, Y. (1998), "The effect of mechanical heterogeneity and limit load of a weld joint with longitudinal weld crack on the J-integral and failure assessment curve", Int. J. Press. Vessels Pip., 75(8), 625-632. https://doi.org/10.1016/S0308-0161(98)00067-2
  9. Magudeeswaran, G., Balasubramanian, V. and Reddy, G.M. (2014), "Effect of welding processes and consumables on fatigue crack growth behaviour of armour grade quenched and tempered steel joints", Defence Technol., 10(1), 47-59. https://doi.org/10.1016/j.dt.2014.01.005
  10. Nathan, S.R., Balasubramanian, V., Malarvizhi, S. and Rao, A.G. (2015), "Effect of welding processes on mechanical and microstructural characteristics of high strength low alloy naval grade steel joints", Defence Technol., 11(3), 308-317. https://doi.org/10.1016/j.dt.2015.06.001
  11. Negre, P., Steglich, D. and Brocks, W. (2004), "Crack extension in aluminium welds: a numerical approach using the Gurson-Tvergaard-Needleman model", Eng. Fract. Mech., 71(16-17), 2365-2383. https://doi.org/10.1016/j.engfracmech.2004.01.007
  12. Paris, P. and Erdogan, F. (1963), "A critical analysis of crack propagation laws", ASME J. Basic Eng. 85(4), 528-533. https://doi.org/10.1115/1.3656900
  13. Paris, P.C., Gomez, M.P. and Anderson, W.E. (1961), "A rational analytic theory of fatigue", Trend Eng, 13(1), 9-14.
  14. Pickard, A.C., Ritchie, R.O. and Knott, J.F. (1975), "Fatigue crack propagation in a type 316 stainless steel weldment", Metals Technol, 2(1), 253-263. https://doi.org/10.1179/030716975803277519
  15. Ravi, S., Balasubramanian, V., Babu, S. and Nasser, S.N. (2004a), "Assessment of some factors influencing the fatigue life of strength mis-matched HSLA steel weldments", Mater. Des., 25(2), 125-135. https://doi.org/10.1016/j.matdes.2003.09.016
  16. Ravi, S., Balasubramanian, V. and Nasser, S.N. (2004b), "Effect of mis-match ratio (MMR) on fatigue crack growth behaviour of HSLA steel welds", Eng. Failure Anal., 11(3), 413-428 https://doi.org/10.1016/j.engfailanal.2003.05.013
  17. Salleh, M.N.M., Ishak, M., Shah, L.H. and Idris, S.R.A. (2016), M "The effect of ER4043 and ER5356 filler metal on welded Al 7075 by metal inert gas welding", Faculty of Mechanical Engineering WIT Transactions on The Built Environment, 166, p. 213.
  18. Stacey, A. and Webster, G.A. (1988), "Influence of residual stress on fatigue crack growth in thick-walled cylinders", ASTM STP, 1004, 107-121.
  19. Zhang, H., Zhang, Y., Li, L. and Ma, X. (2002), "Influence of weld mis-matching on fatigue crack growth behaviors of electron beam welded joints", Mater. Sci. Eng. A, 334(1-2), 141-146. https://doi.org/10.1016/S0921-5093(01)01785-3