DOI QR코드

DOI QR Code

차체의 종류별 로어암 형상의 변화에 따른 내구성 향상에 관한 연구

Durability Improvement due to the Change of Lower Arm by the Class of Automotive Body

  • 한문식 (계명대학교 기계자동차공학과) ;
  • 조재웅 (공주대학교 기계자동차공학부)
  • Han, Moonsik (Department of Mechanical and Automotive Engineering, Keimyung UNIV.) ;
  • Cho, Jaeung (Division of Mechanical and Automotive Engineering, Kongju National UNIV.)
  • 투고 : 2017.08.18
  • 심사 : 2017.09.30
  • 발행 : 2017.12.31

초록

This study analyzed automobile lower arm assembly structure and fatigue to identify configuration changes to enhance structural safety. Parts connected to the car body were fixed and 500 N load was applied at the lower arm head. Maximum equivalent stress and maximum total deformation were minimized for model 1 ( MPa and 0.10315 mm, respectively). Fatigue analysis using extreme SAE bracket history fatigue loads showed model 1 also improved fatigue life ($3.3693{\times}10^5cycles$). This study provides important inputs to improve lower arm durability by modifying the arm configuration.

키워드

참고문헌

  1. Cho, J. U., "Study on Convergence Technique through Structural Analysis on the Axle of Railway Vehicle," Journal of the Korea Convergence Society, Vol. 6, No. 1, pp. 93-101, 2015. https://doi.org/10.15207/JKCS.2015.6.1.093
  2. Cho, J. U., Han, M. S., "Structural Safety Analysis of Car Body," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 7, No. 3, pp. 12-16, 2008.
  3. Lee, J. H., Cho, J. U., "Study on the Convergent Life Evaluation due to the Bumper Configuration of Multipurpose Vehicle," Journal of the Korea Convergence Society, Vol. 6, No. 5, pp. 85-90, 2015. https://doi.org/10.15207/JKCS.2015.6.5.085
  4. Cho, J. U., Min, B. S., Han, M. S., "Basic Study on Impact Analysis of Automobile," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 8, No. 1, pp. 64-70, 2009.
  5. Choi, B. I., Kang, S. J., "Stiffness and Fatigue Strength Analysis of Fuel Cell Vehicle Body Frame," Transaction of the Korean Society of Automotive Engineers, Vol. 19. No. 4, pp. 47-53, 2011.
  6. Lee, J. H., Cho, J. U., "Study on Convergence Technique through Structural Analysis due to The Configuration of Door Hinge," Journal of the Korea Convergence Society, Vol. 6, No. 3, pp. 59-64, 2015. https://doi.org/10.15207/JKCS.2015.6.3.059
  7. Cho, J. U., Han, M. S., "Structural and Fatigue Analysis on Shock Absorber Mount of Automobile," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 11, No. 1, pp. 125-133, 2012.
  8. Lee, K. T., Jun, Y. D. and Choi, D. S., "Evaluation of Vehicle Body Stiffness by Measuring Local Vibration," Transaction of the Korean Society of Automotive Engineers, Vol. 21, No. 6, pp. 195-200, 2013. https://doi.org/10.7467/KSAE.2013.21.6.195
  9. Cho, J. U., Han, M. S., "A Study on Durability of Under Bar at Car through Structural and Fatigue Analysis," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 14, No. 2, pp. 44-50, 2015. https://doi.org/10.14775/ksmpe.2015.14.2.044
  10. Lee, J. H., Cho, J. U., "Convergence Technique Study of Model Tie Rod End by Configuration through Simulation Analysis," Journal of the Korea Convergence Society, Vol. 7, No. 1, pp. 161-166, 2016. https://doi.org/10.15207/JKCS.2016.7.1.161
  11. Ryu, J. M., Park, K. C., Kang, T. W., "A Study on the Structural Design for Safety Improvement of the Winch Mount of an Armored Recovery Vehicle," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 16, No. 1, pp. 58-62, 2017. https://doi.org/10.14775/ksmpe.2016.16.1.058
  12. Kang, H. J., Kim, B. H., Kim, H. J., Seo, J. H., "Structural Weld Strength Analysis on Door Hinge of Field Artillery Ammunition Support Vehicle," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 15, No. 3, pp. 58-65, 2016. https://doi.org/10.14775/ksmpe.2016.15.3.058