Elastomers and Composites

  • 제52권4호
  • /
  • Pages.309-316
  • /
  • 2017
  • /
  • 2092-9676(pISSN)
  • /
  • 2288-7725(eISSN)
한국고무학회 (The Rubber Society of Korea)
권호 표지
DOI QR코드

DOI QR Code

Analysis of Cavity Pressure and Dimension of Molded Part According to V/P Switchover Position in Injection Molding

  • Cho, Jung Hwan (Samyang Central R & D Center) ;
  • Kwon, Soon Yong (Samyang Central R & D Center) ;
  • Roh, Hyung Jin (Samyang Central R & D Center) ;
  • Cho, Sung Hwan (Samyang Central R & D Center) ;
  • Kim, Su Yeon (Department of Mechanical System Design Engineering, Seoul National University of Science and Technology) ;
  • Lyu, Min-Young (Department of Mechanical System Design Engineering, Seoul National University of Science and Technology)
  • 투고 : 2017.12.03
  • 심사 : 2017.12.14
  • 발행 : 2017.12.31
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

In injection molding, the quality of an injection molded product varies greatly depending on the molding conditions. Many researche studies have been conducted on the quality analysis of molded parts according to the molding conditions such as injection pressure, injection temperature, and packing pressure. However, there have not been many studies on the V/P switchover timing. It is known that when a large pressure is applied to a cavity in the packing phase, the cavity pressure is most affected by the packing pressure. In addition, depending on the position (timing) of the packing pressure, it can have a direct influence on quality based on the shrinkage and dimensions of the molded parts. In this study, the change in pressure profile in the cavity according to the V/P switchover position is confirmed. A CAE analysis program (Moldflow) was used to simulate and analyze two models using the PC and PBT materials. In order to compare these results with the actual injection molding results, injection molding was performed for each V/P switchover position, and the correlation between simulation and experiment, especially for the shrinkage of molded parts, was evaluated.

키워드

참고문헌

  1. M. Lee, H. Kim, and M.-Y. Lyu, "A Study on the Warpage of Glass Fiber Reinforced Plastics for Part Design and Operation Condition", The Polymer Society of Korea, 36, 555 (2012). https://doi.org/10.7317/pk.2012.36.5.555
  2. D. V. Rosato and M. G. Rosato, "Injection molding handbook", Springer Science & Business Media, New York, 2012.
  3. R. M. German, "Powder injection molding", Metal Powder Industries Federation, Princeton, 1990.
  4. N. Prabhu, J. Schultz, and S. G. Advani, "Role of Coupling Microscopic and Macroscopic Phenomena During the Semicrystalline Polymers", Polymer Eng. Sci., 41, 1871 (2001). https://doi.org/10.1002/pen.10884
  5. C. Shen, L. Wang, and Q. Li, "Optimization of injection molding process parameters using combination of artificial neural network and genetic algorithm method", Journal of Materials Processing Technology, 183, 412 (2007). https://doi.org/10.1016/j.jmatprotec.2006.10.036
  6. H. Oktem, T. Erzurumlu, and I. Uzman, "Application of Taguchi optimization technique in determining plastic injection molding process parameters for a thin-shell part", Materials & Design, 28, 1271 (2007). https://doi.org/10.1016/j.matdes.2005.12.013
  7. M. C. Huang and C. C. Tai, "The effective factors in the warpage problem of an injection-molded part with a thin shell feature", Journal of Materials Processing Technology, 110, 1 (2001). https://doi.org/10.1016/S0924-0136(00)00649-X
  8. M. S. Huang, "Cavity pressure based grey prediction of the filling-to-packing switchover point for injection molding", Journal of Materials Processing Technology, 183, 419 (2007). https://doi.org/10.1016/j.jmatprotec.2006.10.037
  9. A. Kramschuster, R. Cavitt, D. Ermer, Z. Chen, and L. S. Turng, "Quantitative study of shrinkage and warpage behavior for microcellular and conventional injection molding", Polymer Engineering & Science, 45, 1408 (2005). https://doi.org/10.1002/pen.20410
  10. Q. Guan, K. Shen, J. Ji, and J. Zhu, "Structure and properties of self-reinforced polyethylene prepared by oscillating packing injection molding under low pressure", Journal of Applied Polymer Science, 55, 1797 (1995). https://doi.org/10.1002/app.1995.070551310
  11. R. Pantani, I. Coccorullo, V. Speranza, and G. Titomanlio, "Morphology evolution during injection molding: effect of packing pressure", Polymer, 48, 2778 (2007). https://doi.org/10.1016/j.polymer.2007.03.007
  12. H. Yaguchi, H. Hojo, D. G. Lee, and E. G. Kim, "Measurement of planar orientation of fibers for reinforced thermoplastics using image processing", Int. Polym. Processing, 10, 262 (1995). https://doi.org/10.3139/217.950262
  13. K. M. B. Jansen, D. J. Van Dijk, and E. V. Burgers, "Experimental validation of shrinkage predictions for injection molded products", Int. Polym. Processing, 13, 99 (1998). https://doi.org/10.3139/217.980099
  14. M.-Y. Lyu, J. G. Choi, and Y. Pae, "Investigation of the Jetting Phenomena in Injection Molding for Various Injection Speeds, Resins and Mold Shapes", Transactions of Materials Processing, 12, 3 (2003). https://doi.org/10.5228/KSPP.2003.12.1.003
  15. D. Kazmer and P. Barkan, Multi-cavity pressure control in the filling and packing stages of the injection molding process. Polymer Engineering & Science, 37, 1865 (1997). https://doi.org/10.1002/pen.11837