DOI QR코드

DOI QR Code

Wavelet analysis based damage localization in steel frames with bolted connections

  • Pnevmatikos, Nikos G. (Department of Civil Engineering, Surveying and Geoinformatics, Technological Educational Institute of Athens, Faculty of Technological Application) ;
  • Blachowski, Bartlomiej (Polish Academy of Sciences, Institute of Fundamental Technological Research) ;
  • Hatzigeorgiou, George D. (Hellenic Open University, School of Science and Technology) ;
  • Swiercz, Andrzej (Polish Academy of Sciences, Institute of Fundamental Technological Research)
  • 투고 : 2015.12.30
  • 심사 : 2016.09.21
  • 발행 : 2016.12.25

초록

This paper describes an application of wavelet analysis for damage detection of a steel frame structure with bolted connections. The wavelet coefficients of the acceleration response for the healthy and loosened connection structure were calculated at each measurement point. The difference of the wavelet coefficients of the response of the healthy and loosened connection structure is selected as an indicator of the damage. At each node of structure the norm of the difference of the wavelet coefficients matrix is then calculated. The point for which the norm has the higher value is a candidate for location of the damage. The above procedure was experimentally verified on a laboratory-scale 2-meter-long steel frame. The structure consists of 11 steel beams forming a four-bay frame, which is subjected to impact loads using a modal hammer. The accelerations are measured at 20 different locations on the frame, including joints and beam elements. Two states of the structure are considered: healthy and damaged one. The damage is introduced by means of loosening two out of three bolts at one of the frame connections. Calculating the norm of the difference of the wavelet coefficients matrix at each node the higher value was found to be at the same location where the bolts were loosened. The presented experiment showed the effectiveness of the wavelet approach to damage detection of frame structures assembled using bolted connections.

키워드

참고문헌

  1. Alonso, R., Noori, M., Saadat, S., Masuda, A. and Hou, Z. (2004), "Effects of excitation frequency on detection accuracy of orthogonal wavelet decomposition for structural health monitoring", Earthq. Eng. Eng. Vib., 3(1), 101-106. https://doi.org/10.1007/BF02668855
  2. Blachowski, B. and Gutkowski, W. (2010), "Revised assumptions for monitoring and control of 3D lattice structures", Proceedings of the 11th Pan-American Congress of Applied Mechanics PACAM XI, Foz do Iguassu, Brasil, January.
  3. Blachowski, B., Swiercz, A. and Pnevmatikos, N. (2015), "Experimental verification of damage location techniques for frame structures assembled using bolted connections", Proceedings of the COMPDYN 2015, 5th ECCOMAS Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering, (Eds., M. Papadrakakis, V. Papadopoulos, V. Plevris), Crete Island, Greece, May.
  4. Bukkapatnam, S., Nichols, J., Seaver, M., Trickey, S. and Hunter, M. (2005), "A wavelet-based, distortion energy approach to structural health monitoring", Struct. Health Monit., 4, 247-258. https://doi.org/10.1177/1475921705055246
  5. Caddemi, S. and Calio, I. (2014), "Exact reconstruction of multiple concentrated damages on beams", Acta Mechanica, 225(11), 3137-3156. https://doi.org/10.1007/s00707-014-1105-5
  6. Caddemi, S. and Morassi, A. (2013), "Multi-cracked Euler-Bernoulli beams: Mathematical modeling and exact solutions", Int. J. Solids Struct., 50(6), 944-956. https://doi.org/10.1016/j.ijsolstr.2012.11.018
  7. Casciati, F. and Casciati, S. (2006), "Structural health monitoring by Lyapunov exponents of non-linear time series", Struct. Control Health Monit., 13(1), 132-146. https://doi.org/10.1002/stc.141
  8. Chandrashekhar, M. and Ranjan, G. (2009), "Structural damage detection using modal curvature and fuzzy logic", Struct. Health Monit., 8 (2), 267-282. https://doi.org/10.1177/1475921708102088
  9. Chatzi, E.N., Smyth, A.W. and Masri, S.F. (2010), "Experimental application of on-line parametric identification for non-linear hysteretic systems with model uncertainty", Struct. Saf., 32(5), 326-337. https://doi.org/10.1016/j.strusafe.2010.03.008
  10. Ciambella, J., Vestroni, F. and Vidoli, S. (2011), "Damage observability, localization and assessment based on eigenfrequencies and eigenvectors curvatures", Smart Struct. Syst., 8(2), 191-204. https://doi.org/10.12989/sss.2011.8.2.191
  11. De Roeck, G. and Reynders, E. (2009), "Exploring the limits and extending the borders of structural health monitoring", Proceedings Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering, COMPDYN, ECCOMAS, (Eds., M. Papadrakakis, N.D. Lagaros and M. Fragiadakis), Rhodes, Greece.
  12. Dertimanis, V. and Chatzi, E. (2014), "A hybrid evolution strategy approach to the structural identification problem via state-space models", Proceedings of the Conferences 6th World Conference on Structural Control and Monitoring (6WCSCM), ISBN 978-84-942844-5-8, Barcelona, Spain.
  13. Fan, W. and Qiao, P. (2011), "Vibration-based damage identification methods: A reviewand comparative study", Struct. Health Monit., 10(1), 83-111. https://doi.org/10.1177/1475921710365419
  14. Fan, Z., Feng, X. and Zhou, J. (2013), "A novel transmissibility concept based on wavelet transform for structural damage detection", Smart Struct. Syst., 12(3), 291-308. https://doi.org/10.12989/sss.2013.12.3_4.291
  15. Friswell, M.I. and Mottershead, J.E. (1995), Finite Element Model Updating in Structural Dynamics, Kluwer Academic Publishers Group.
  16. Goggins, J., Broderick, B., Basu, B. and Elghazouli, A. (2007), "Investigation of the seismic response of braced frames using wavelet analysis", Struct. Control Health Monit., 14(4), 627-648. https://doi.org/10.1002/stc.180
  17. He, W.Y. and Zhu, S. (2015), "Adaptive-scale damage detection strategy for plate structures based on wavelet finite element model", Struct. Eng. Mech., 54(2), 239-256. https://doi.org/10.12989/sem.2015.54.2.239
  18. Hera, A. and Hou, Z. (2004), "Application of wavelet approach for ASCE structural health monitoring benchmark studies", J. Eng. Mech. - ASCE, 130(1), 96-104. https://doi.org/10.1061/(ASCE)0733-9399(2004)130:1(96)
  19. Hou, Z., Noori, M. and Arnand, St. (2000), "Wavelet-based approach for structural damage detection", J. Eng. Mech. - ASCE, 126(7), 677-683. https://doi.org/10.1061/(ASCE)0733-9399(2000)126:7(677)
  20. Humar, J., Bagchi, A. and Xu, H.P. (2006), "Performance of vibration-based techniques for the identification of structural damage", Struct. Health Monit., 5(3), 215-241. https://doi.org/10.1177/1475921706067738
  21. Khatam, H., Golafshani, A.A., Beheshti-Aval, S.B. and Noori, M. (2007), "Harmonic class loading for damage identification in beams using wavelet analysis", Struct. Health Monit., 6(1), 67-80. https://doi.org/10.1177/1475921707072064
  22. Kim, H. and Melehem, H. (2004), "Damage detection of structures by wavelet analysis", Eng. Struct., 26(3), 347-362. https://doi.org/10.1016/j.engstruct.2003.10.008
  23. Kirmser, P.G. (1944), "The effect of discontinuities of the natural frequency of beams", Proceedings of the American Society for Testing Materials, Philadelphia, PA.
  24. Krawczuk, M., Palacz, M. and Ostachowicz, W. (2004), "Wave propagation in plate structures for crack detection", Finite Elem. Anal. Des., 40(9-10), 991-1004. https://doi.org/10.1016/j.finel.2003.03.001
  25. Law, S.S., Zhu, X.Q., Tian, Y.J., Li, X.Y. and Wu, S.Q. (2013), "Statistical damage classification method based on wavelet packet analysis", Struct. Eng. Mech., 46 (4), 459-486 https://doi.org/10.12989/sem.2013.46.4.459
  26. Lima, M.M., Amiri, G.G. and Bagheri, A. (2012), "Wavelet-based method for damage detection of non-linear structures", J. Civil Eng.Urbanism, 2(4), 149-153.
  27. Liu, J.L., Wang, Z.C., Ren, W.X. and Li, X.X. (2015), "Structural time-varying damage detection using synchrosqueezing wavelet transform", Smart Struct. Syst., 15(1), 119-133. https://doi.org/10.12989/sss.2015.15.1.119
  28. Masri, S.F., Nakamura, M., Chassiakos, A.G. and Caughey, T.K. (1996), "Neural network approach to detection of changes in structural parameters", J. Eng. Mech. - ASCE, 122 (4), 350-360. https://doi.org/10.1061/(ASCE)0733-9399(1996)122:4(350)
  29. Mehrjoo, M., Khaji, N., Moharrami, H. and Bahreininejad, A. (2008), "Damage detection of truss bridge joints using Artificial Neural Networks", Expert Syst. Appl., 35(3), 1122-1131. https://doi.org/10.1016/j.eswa.2007.08.008
  30. Nagarajaiah, S. and Basu, B. (2009), "Output only modal identification and structural damage detection using time frequency & wavelet techniques", Earthq. Eng. Eng, Vib., 8(4), 583-605. https://doi.org/10.1007/s11803-009-9120-6
  31. Newland, D.E. (1993), An Introduction to Random Vibrations, Spectral and Wavelet Analysis. Longman, New York.
  32. Noh, H.Y., Nair, K., Lignos, D.G. and Kiremidjian, A.S. (2011), "Use of wavelet-based damage-sensitive features for structural damage diagnosis using strong motion data", J. Struct. Eng. - ASCE, 137(10), 1215-1228. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000385
  33. Noh. H.Y., Lignos, D.G., Nair, K. and Kiremidjian, A.S. (2012), "Development of fragility functions as a damage classification method for steel moment-resisting frames using a wavelet-based damage sensitive feature", Earthq. Eng. Struct. D., 41(4), 681-696. https://doi.org/10.1002/eqe.1151
  34. Papadimitriou, C. and Ntotsios, E. (2009), "Structural model updating using vibration measurements", Proceedings of the Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering, ECCOMAS, COMPDYN, (Eds., M. Papadrakakis, N.D. Lagaros, M. Fragiadakis), Rhodes, Greece.
  35. Razi, P., Esmaeel, R.A. and Taheri, F. (2013), "Improvement of a vibration-based damage detection approach for health monitoring of bolted flange joints in pipelines", Struct. Health Monit., 12(3), 207-224. https://doi.org/10.1177/1475921713479641
  36. Rucka, M. and Wilde, K. (2010), "Neuro-wavelet damage detection technique in beam, plate and shell structures with experimental validation", J . Theoretical Appl. Mech., 48(3), 579-604.
  37. Sakellariou, J. and Fassois, S. (2006), "Stochastic output error vibration-based damage detection and assessment in structures under earthquake excitation", J. Sound Vib., 127(3), 1048-1067.
  38. Soyoz, S. and Feng, M. (2007), "Instantaneous damage detection of bridge structures and experimental verification", Struct. Control Health Monit., 15(7),958-973. https://doi.org/10.1002/stc.229
  39. Staszewski, W.J. (1998), "Structural and mechanical damage detection using wavelets", J. Shock Vib. Digest, 30(6), 457-472. https://doi.org/10.1177/058310249803000602
  40. Swiercz, A., Kolakowski, P. and Holnicki-Szulc J. (2007), "Structural damage identification using low frequency non-resonance harmonic excitation", Key Eng. Mater., 34(7), 427-432.
  41. Taha, R., Noureldin, M., Lucero, A. and Baca, T. (2006), "Wavelet transform for structural health monitoring:a compendium of uses and features", Struct. Health Monit., 5 (3), 267-295. https://doi.org/10.1177/1475921706067741
  42. Vanik, M.W. and Beck, J.L. (1997), "A Bayesian probabilistic approach to structural health monitoring", Proceedings of the International Workshop on Structural Health Monitoring: Current Status and Perspectives, Stanford University, Stanford, CA.
  43. Wang, C., Ren, W.X., Wang, Z.C. and Zhu, H.P. (2014), "Time-varying physical parameter identification of shear type structures based on discrete wavelet transform", Smart Struct. Syst., 14(5), 831-845. https://doi.org/10.12989/sss.2014.14.5.831
  44. Wu, X, Ghabossi, J. and Garrett, J.H. (1992), "Use of neural networks in detection of structural damage", Comput. Struct., 42(4), 649-659. https://doi.org/10.1016/0045-7949(92)90132-J
  45. Yang, J., Xia, Y. and Loh, C. (2014), "Damage identification of bolt connections in a steel frame", J. Struct.Eng -ASCE, 140(3), 04013064. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000831
  46. Yun, G.J., Ogorzalek, K.A. Dyke, S.J. and Song, W. (2009), "A two-stage damage detection approach based on subset selection and genetic algorithms", Smart Struct. Syst., 5(1), 1-21. https://doi.org/10.12989/sss.2009.5.1.001

피인용 문헌

  1. Long-Term In-Service Monitoring and Performance Assessment of the Main Cables of Long-Span Suspension Bridges vol.17, pp.6, 2017, https://doi.org/10.3390/s17061414
  2. An assessment framework for sensor-based detection of critical structural conditions with consideration of load uncertainty vol.12, 2017, https://doi.org/10.1016/j.istruc.2017.06.001
  3. Looseness localization for bolted joints using Bayesian operational modal analysis and modal strain energy vol.10, pp.11, 2018, https://doi.org/10.1177/1687814018808698
  4. Application of the Random Decrement Technique in Damage Detection under Moving Load vol.8, pp.5, 2018, https://doi.org/10.3390/app8050753
  5. Condition Prediction of Existing Concrete Bridges as a Combination of Visual Inspection and Analytical Models of Deterioration vol.9, pp.1, 2019, https://doi.org/10.3390/app9010148
  6. Optimal Placement of Virtual Masses for Structural Damage Identification vol.19, pp.2, 2019, https://doi.org/10.3390/s19020340
  7. A hybrid structural health monitoring technique for detection of subtle structural damage vol.22, pp.5, 2016, https://doi.org/10.12989/sss.2018.22.5.587
  8. Deep Learning-Based Damage, Load and Support Identification for a Composite Pipeline by Extracting Modal Macro Strains from Dynamic Excitations vol.8, pp.12, 2016, https://doi.org/10.3390/app8122564
  9. A Novelty Detection Approach for Tendons of Prestressed Concrete Bridges Based on a Convolutional Autoencoder and Acceleration Data vol.19, pp.7, 2016, https://doi.org/10.3390/s19071633
  10. Bayesian Prediction of Pre-Stressed Concrete Bridge Deflection Using Finite Element Analysis vol.19, pp.22, 2016, https://doi.org/10.3390/s19224956
  11. The Teager-Kaiser Energy Cepstral Coefficients as an Effective Structural Health Monitoring Tool vol.9, pp.23, 2019, https://doi.org/10.3390/app9235064
  12. Damage Detection in Plates with the Use of Laser-Measured Mode Shapes vol.2020, pp.None, 2016, https://doi.org/10.1155/2020/8858126
  13. Determination of Monitoring Parameters for Fatigue Behavior of Steel-Concrete Composite Bridge Girders with Welded Full Depth Transverse Stiffeners vol.12, pp.1, 2016, https://doi.org/10.3390/su12010283
  14. Detection of Bolt Looseness Based on Average Autocorrelation Function vol.2021, pp.None, 2016, https://doi.org/10.1155/2021/6662686
  15. Indoor Wavelet OFDM VLC-MIMO System: Performance Evaluation vol.13, pp.2, 2016, https://doi.org/10.3390/sym13020270
  16. Field experiment on a PSC-I bridge for convolutional autoencoder-based damage detection vol.20, pp.4, 2016, https://doi.org/10.1177/1475921720926267