DOI QR코드

DOI QR Code

Electromagnetic energy harvesting from structural vibrations during earthquakes

  • Shen, Wenai (School of Civil Engineering and Mechanics, Huazhong University of Science and Technology) ;
  • Zhu, Songye (Department of Civil and Environmental Engineering, The Hong Kong Polytechnic University) ;
  • Zhu, Hongping (School of Civil Engineering and Mechanics, Huazhong University of Science and Technology) ;
  • Xu, You-lin (Department of Civil and Environmental Engineering, The Hong Kong Polytechnic University)
  • Received : 2015.05.30
  • Accepted : 2015.08.20
  • Published : 2016.09.25

Abstract

Energy harvesting is an emerging technique that extracts energy from surrounding environments to power low-power devices. For example, it can potentially provide sustainable energy for wireless sensing networks (WSNs) or structural control systems in civil engineering applications. This paper presents a comprehensive study on harvesting energy from earthquake-induced structural vibrations, which is typically of low frequency, to power WSNs. A macroscale pendulum-type electromagnetic harvester (MPEH) is proposed, analyzed and experimentally validated. The presented predictive model describes output power dependence with mass, efficiency and the power spectral density of base acceleration, providing a simple tool to estimate harvested energy. A series of shaking table tests in which a single-storey steel frame model equipped with a MPEH has been carried out under earthquake excitations. Three types of energy harvesting circuits, namely, a resistor circuit, a standard energy harvesting circuit (SEHC) and a voltage-mode controlled buck-boost converter were used for comparative study. In ideal cases, i.e., resistor circuit cases, the maximum electric energy of 8.72 J was harvested with the efficiency of 35.3%. In practical cases, the maximum electric energy of 4.67 J was extracted via the buck-boost converter under the same conditions. The predictive model on output power and harvested energy has been validated by the test data.

Keywords

Acknowledgement

Supported by : National Natural Science Foundation of China

References

  1. Alavi, A.H., Hasni, H., Lajnef, N., Chatti, K. and Faridazar, F. (2016), "An intelligent structural damage detection approach based on self-powered wireless sensor data", Automat. Constr., 62, 24-44. https://doi.org/10.1016/j.autcon.2015.10.001
  2. Auge, L.J. (2003), "Structural magnetic induction dampers in buildings", Master thesis, Massachusetts Institute of Technology, USA.
  3. Cao, M. and Zuo, L. (2014), "Energy harvesting from building seismic isolation with multi-mode resonant shunt circuits", Proceedings of the ASME, San Antonio, TX, USA.
  4. Casciati, F. and Rossi, R. (2007), "A power harvester for wireless sensing applications", Struct. Control Health., 14(4), 649-659. https://doi.org/10.1002/stc.179
  5. Clough, R.W. and Penzien, J. (1993), Dynamics of structures, 2nd Ed., McGraw-Hill.
  6. Dissertation, California Institute of Technology, Pasadena, California, USA.
  7. Elvin, N.G., Lajnef, N. and Elvin, A.A. (2006), "Feasibility of structural monitoring with vibration powered sensors", Smart Mater. Struct., 15(4), 977-986. https://doi.org/10.1088/0964-1726/15/4/011
  8. GB. (2010), "Code for seismic design of buildings", GB50011-2010, Beijing, China.
  9. Harb, A. (2011), "Energy harvesting: State-of-the-art", Renew. Energ., 36(10), 2641-2654. https://doi.org/10.1016/j.renene.2010.06.014
  10. Jung, H.J., Jang, D.D., Lee, H.J., Lee, I.W. and Cho, S.W. (2010), "Feasibility test of adaptive passive control system using MR fluid damper with electromagnetic induction part", J. Eng. Mech. - ASCE, 136(2), 254-259. https://doi.org/10.1061/(ASCE)0733-9399(2010)136:2(254)
  11. Jung, H.J., Kim, I.H. and Jang, S.J. (2011), "An energy harvesting system using the wind-induced vibration of a stay cable for powering a wireless sensor node", Smart Mater. Struct., 20(7), 075001. https://doi.org/10.1088/0964-1726/20/7/075001
  12. Jung, H.J., Park, J. and Kim, I.H. (2012), "Investigation of applicability of electromagnetic energy harvesting system to inclined stay cable under wind load", IEEE T. Magn., 48(11), 3478-3481. https://doi.org/10.1109/TMAG.2012.2202889
  13. Kim, I.H., Jang, S.J. and Jung, H.J. (2013), "Performance enhancement of a rotational energy harvester utilizing wind-induced vibration of an inclined stay cable", Smart Mater. Struct., 22(7), 075004. https://doi.org/10.1088/0964-1726/22/7/075004
  14. Lajnef, N., Chakrabartty, S. and Elvin, N. (2008), "A Piezo-powered Floating-gate Sensor Array for Long-term Fatigue Monitoring in Biomechanical Implants", IEEE Trans. Biomed. Circuits Syst.,2(3)164-172. https://doi.org/10.1109/TBCAS.2008.2001473
  15. Langley, R. (2014), "A general mass law for broadband energy harvesting", J. Sound Vib., 333(3), 927-936. https://doi.org/10.1016/j.jsv.2013.09.036
  16. Lefeuvre, E., Audigier, D., Richard, C. and Guyomar, D. (2007), "Buck-boost converter for sensorless power optimization of piezoelectric energy harvester", IEEE T. Power Electr., 22(5), 2018-2025. https://doi.org/10.1109/TPEL.2007.904230
  17. Lefeuvre, E., Badel, A., Richard, C., Petit, L. and Guyomar, D. (2006), "A comparison between several vibration-powered piezoelectric generators for standalone systems", Sensor. Actuat. A: Phys., 126(2), 405-416. https://doi.org/10.1016/j.sna.2005.10.043
  18. Lei, Y., Tang, Y.L., Wang, J.X., Jiang, Y.Q. and Luo, Y. (2012), "Intelligent monitoring of multistory buildings under unknown earthquake excitation by a wireless sensor network", Int. J. Distrib. Sens. N., 2012, 914638.
  19. Liang, J.R. and Liao, W.H. (2009), "Piezoelectric energy harvesting and dissipation on structural damping", J. Intel. Mat. Syst. Str., 20(5), 515-527. https://doi.org/10.1177/1045389X08098194
  20. Lu, Q., Loong, C., Chang, C.C. and Dimitrakopoulos, E.G. (2014), "Scavenging vibration energy from seismically-isolated bridges using an electromagnetic harvester", Proceedings of the SPIE, 906101-1, San Diego, California, USA.
  21. Lynch, J.P. and Loh, K.J. (2006), "A Summary Review of Wireless Sensors and Sensor Networks for Structural Health Monitoring", Shock Vib. Digest, 38(2), 91-128. https://doi.org/10.1177/0583102406061499
  22. Mahlknecht, S. (2004), "Energy-self-sufficient wireless sensor networks for the home and building environment", Ph.D. Dissertation, Universitat von Pretoria, Wien.
  23. Mitcheson, P.D. (2005), "Analysis and Optimisation of Energy-Harvesting Micro-Generator Systems", Ph.D. Dissertation, Imperial College London, London.
  24. Mitcheson, P.D., Green, T.C., Yeatman, E.M. and Holmes, A.S. (2004), "Architectures for vibration-driven micropower generators", J. Microelectromech. S., 13(3), 429-440. https://doi.org/10.1109/JMEMS.2004.830151
  25. Park, G., Rosing, T., Todd, M.D., Farrar, C.R. and Hodgkiss, W. (2008), "Energy harvesting for structural health monitoring sensor networks", J. Infrastruct. Syst., 14(1), 64-79. https://doi.org/10.1061/(ASCE)1076-0342(2008)14:1(64)
  26. Ramadan, K.S., Sameoto, D. and Evoy, S. (2014), "A review of piezoelectric polymers as functional materials for electromechanical transducers", Smart Mater. Struct., 23(3), 033001. https://doi.org/10.1088/0964-1726/23/3/033001
  27. Rhimi, M. and Lajnef, N. (2012), "Tunable energy harvesting from ambient vibrations in civil structures", J. Energ. Eng., 138(4), 185-193. https://doi.org/10.1061/(ASCE)EY.1943-7897.0000077
  28. Rice, J.A. and Spencer, B.F. (2008), "Structural health monitoring sensor development for the Imote2 platform", Proceedings of the SPIE, San Diego, California, USA.
  29. Roundy, S., Wright, P.K. and Rabaey, J. (2003), "A study of low level vibrations as a power source for wireless sensor nodes" Comput. Commun., 26(11), 1131-1144. https://doi.org/10.1016/S0140-3664(02)00248-7
  30. Sapinski, B. (2011), "Experimental study of a self-powered and sensing MR-damper-based vibration control system", Smart Mater. Struct., 20(10), 105007. https://doi.org/10.1088/0964-1726/20/10/105007
  31. Sazonov, E., Li, H., Curry, D. and Pillay, P. (2009), "Self-powered sensors for monitoring of highway bridges", IEEE Sens. J., 9(11), 1422-1429. https://doi.org/10.1109/JSEN.2009.2019333
  32. Scruggs, J.T. (1999), "Active, regenerative control of civil structures", Master Thesis, Virginia Polytechnic Institute and State University, Blacksburg, Virginia, USA.
  33. Scruggs, J.T. (2004), "Structural control using regenerative force actuation networks", Ph.D. Dissertation, California Institute of Technology, Pasadena, California, USA.
  34. Scruggs, J.T. and Iwan, W. (2005), "Structural control with regenerative force actuation networks", Struct. Control Health., 12(1), 25-45. https://doi.org/10.1002/stc.50
  35. Shen, W. (2014), "Electromagnetic damping and energy harvesting devices in civil structures", Ph.D. Dissertation, The Hong Kong Polytechnic University, Hong Kong.
  36. Shen, W. and Zhu, S. (2015), "Harvesting energy via electromagnetic damper: Application to bridge stay cables", J. Intel. Mat. Syst. Str., 26(1), 3-19. https://doi.org/10.1177/1045389X13519003
  37. Shen, W.A., Lei, Y., Hu, L. and Wang, Y. (2012), "Feasibility of output-only modal identification using wireless sensor network: A quantitative field experimental study", Int. J. Distrib. Sens. N., 2012:560161.
  38. Shen, W.A., Zhu, S. and Xu, Y.L. (2012), "An experimental study on self-powered vibration control and monitoring system using electromagnetic TMD and wireless sensors", Sensor. Actuat. A: Phys., 180(2012), 166-176. https://doi.org/10.1016/j.sna.2012.04.011
  39. Soong, T.T. and Grigoriu, M. (1993), "Random vibration of mechanical and structural systems", PTR Prentice Hall.
  40. Spencer, B.F., Cho, S. and Sim, S.H. (2011), "Wireless monitoring of civil infrastructure comes of age", Struct. Mag., 12-16.
  41. Torfs, T., Sterken, T., Brebels, S., Santana, J., van den Hoven, R., Spiering, V., Bertsch, N., Trapani D. and Zonta, D. (2013), "Low power wireless sensor network for building monitoring", IEEE Sens. J., 13(3), 909-915. https://doi.org/10.1109/JSEN.2012.2218680
  42. Van Noorden, R. (2012), "New year, new science", Nature, 481(7379), 12. https://doi.org/10.1038/481012a
  43. Vullers, R., Schaijk, R., Visser, H., Penders, J. and Hoof, C. (2010), "Energy harvesting for autonomous wireless sensor networks", IEEE Solid-St. Circ. Mag., 2(2), 29-38. https://doi.org/10.1109/MSSC.2010.936667
  44. Wang, Z., Chen Z.Q. and Spencer, B.F. (2009), "Self-powered and sensing control system based on MR damper: presentation and application", Proceedings of the SPIE Smart Structures/NDE, 729240.
  45. Williams, C.B. and Yates, R.B. (1996), "Analysis of a micro-electric generator for microsystems", Sensor. Actuat. A: Phys., 52(1-3), 8-11. https://doi.org/10.1016/0924-4247(96)80118-X
  46. Yang, C.Y. (1986), "Random Vibration of Structures", John Wiley & Sons, New York.
  47. Zhu, S., Shen, W.A. and Xu, Y.L. (2012), "Linear electromagnetic devices for vibration damping and energy harvesting: Modeling and testing", Eng. Struct., 34, 198-212. https://doi.org/10.1016/j.engstruct.2011.09.024

Cited by

  1. Shunt Damping Vibration Control Technology: A Review vol.7, pp.5, 2017, https://doi.org/10.3390/app7050494
  2. Analysis of piezoelectric energy harvester under modulated and filtered white Gaussian noise vol.104, 2018, https://doi.org/10.1016/j.ymssp.2017.10.031
  3. Vibration Control Design for a Plate Structure with Electrorheological ATVA Using Interval Type-2 Fuzzy System vol.7, pp.7, 2017, https://doi.org/10.3390/app7070707
  4. Energy regenerative tuned mass dampers in high-rise buildings vol.25, pp.2, 2018, https://doi.org/10.1002/stc.2072
  5. Innovative technologies in manufacturing, mechanics and smart civil infrastructure 2017, https://doi.org/10.1080/19475411.2017.1376359
  6. Improving low-frequency piezoelectric energy harvesting performance with novel X-structured harvesters vol.94, pp.2, 2018, https://doi.org/10.1007/s11071-018-4432-6
  7. Unify Energy Harvesting and Vibration Control Functions in Randomly Excited Structures with Electromagnetic Devices vol.145, pp.1, 2019, https://doi.org/10.1061/(ASCE)EM.1943-7889.0001548
  8. A dual electromagnetic array with intrinsic frequency up-conversion for broadband vibrational energy harvesting vol.114, pp.5, 2019, https://doi.org/10.1063/1.5083910
  9. The tuned mass-damper-inerter for harmonic vibrations suppression, attached mass reduction, and energy harvesting vol.19, pp.6, 2017, https://doi.org/10.12989/sss.2017.19.6.665
  10. Self-powered hybrid electromagnetic damper for cable vibration mitigation vol.20, pp.3, 2017, https://doi.org/10.12989/sss.2017.20.3.285
  11. An intelligent fuzzy theory for ocean structure system analysis vol.9, pp.2, 2016, https://doi.org/10.12989/ose.2019.9.2.179
  12. Seismic Control of SDOF Systems with Nonlinear Eddy Current Dampers vol.9, pp.16, 2019, https://doi.org/10.3390/app9163427
  13. All-passive nonlinear electromagnetic metastructure for simultaneous energy harvesting and earthquake mitigation vol.129, pp.5, 2020, https://doi.org/10.1209/0295-5075/129/58004
  14. Intelligent fuzzy algorithm for nonlinear discrete-time systems vol.42, pp.7, 2016, https://doi.org/10.1177/0142331219891383
  15. LMI based criterion for reinforced concrete frame structures vol.9, pp.4, 2020, https://doi.org/10.12989/acc.2020.9.4.407
  16. A low-cost and efficient d33-mode piezoelectric tuned mass damper with simultaneously optimized electrical and mechanical tuning vol.32, pp.6, 2016, https://doi.org/10.1177/1045389x20966056
  17. Experimental investigation of T-shaped piezoelectric energy harvester activating coupled transverse and shear mode vol.577, pp.1, 2016, https://doi.org/10.1080/00150193.2021.1916347
  18. Nonlinear vibration energy harvesting and vibration suppression technologies: Designs, analysis, and applications vol.8, pp.3, 2016, https://doi.org/10.1063/5.0051432