Journal of Advanced Marine Engineering and Technology

The Korean Society of Marine Engineering (한국마린엔지니어링학회)
권호 표지
DOI QR코드

DOI QR Code

A forging die design to improve the flower shape of flange bolt

플랜지 볼트의 플라워 형상 결함 개선을 위한 단조 금형설계

  • Kim, Kwan-Woo (Department of Mechanical Engineering, Chungbuk National University) ;
  • Lee, Geun-Tae (Department of Precision Mechanical Engineering, Chungbuk National University) ;
  • Cho, Hae-Young (Department of Mechanical Engineering, Chungbuk National University)
  • Received : 2015.12.08
  • Accepted : 2016.04.29
  • Published : 2016.05.31
Download PDF
⟨ Previous Next ⟩

Abstract

Flange bolt has a circular flange under the head that acts like a washer to distribute the clamping load over a large area. Flange bolt has usually been manufactured by cold forging. Flower shape defect occurs in the flange forging stage. This defect causes lack of dimensional accuracy and low quality. So it is needed to improve these forging defects. In this study, die design method for flower shape defect of flange bolt was suggested. In order to improve flower shape defect, inner diameter of the addition die in conventional forging process was modified. The forging process with applied modified die was simulated by commercial FEM code DEFORM-3D. The simulated results for modified die were confirmed by experimental trials with the same condition.

플랜지 볼트는 체결하중을 분산시키기 위한 와셔와 같은 역할을 하는 플랜지를 가지고 있으며, 주로 냉간단조로 성형된다. 플랜지의 단조 시 꽃무늬 모양의 결함이 발생할 수 있다. 이 결함은 치수 정밀도 및 품질 저하 등의 문제점을 야기할 수 있어 이에 대한 개선이 요구된다. 본 논문에서는 플랜지 볼트의 플라워 형상 결함을 개선하기 위한 금형 설계방법을 제안하고자 하였다. 이를 위해 기존의 단조 공정에서 앞판의 내경을 변수로 금형을 수정하였다. 수정된 금형을 적용한 단조 공정은 상용 유한요소해석 코드인 DEFORM-3D를 이용하여 시뮬레이션 하였고, 해석결과를 기준으로 단조 실험을 하여 결과의 신뢰성을 검증하였다.

Keywords

References

  1. K. H. Kim, D. B. Kim, I. H. Lee, and H. Y. Cho, "Prediction of dimensional accuracy of flange bolt in cold forging using finite element Mmthod," Journal of Industrial Science and Technology Institute, vol. 28, no. 2, pp. 55-61, 2014 (in Korean).
  2. T. H. Kim, B. M. Kim, and J. C. Choi, "Methodology of tool analysis to improve the accuracy of cold forged parts," Journal of the Korean Society for Precision Engineering, vol. 12, no. 1, pp. 29-37, 1995 (in Korean).
  3. U. J. Jung, J. J. Lee, and G. J. Park, "A preliminary study on the optimal shape design of the axisymmetric forging component using equivalent static loads," Transactions of the Korean Society of mechanical engineers A, vol. 35, no. 1, pp. 1-10, 2011 (in Korean). https://doi.org/10.3795/KSME-A.2011.35.1.001
  4. S. J. Jang, M. C. Lee, S. H. Shim, Y. H. Son, D. J. Yoon, and M. S. Joun, "Finite element analysis of manufacturing process of a 12 point flange head bolt with emphasis on thread rolling process," Transactions of Materials Processing, vol. 19, no. 4, pp. 248-252, 2010 (in Korean). https://doi.org/10.5228/KSPP.2010.19.4.248
  5. J. W. Kim, S. W. Chae, S. S. Han, and Y. H. Son, "Manufacturing process design of aluminum alloy bolt," Journal of the Korean Society for Precision Engineering, vol. 27, no. 5, pp. 63-68, 2015 (in Korean).
  6. D. C. Ko, W. H. Hwang, S. K. Lee, and B. M. Kim, "A study on the method of residual stress relaxation during wire drawing and evaluation of residual stress using nano indentation test," Journal of the Korean Society of Precision Engineering, vol. 23 no. 5, pp. 162-169, 2006 (in Korean).